Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
- Bpq32
- Messages
Search
|
Re: Need Advice: MAP through an Internet T-Mobile, Verizon, etc. "can"
Thank you to Lee and Mark for taking the time to respond.?
Once I digest the info and work on it and get back to you with my results.
73 de Chris
ww2bsa
|
|
Re: Need Advice: MAP through an Internet T-Mobile, Verizon, etc. "can"
On Fri, Feb 28, 2025 at 12:12?PM Mark Taylor via <mtaylor=[email protected]> wrote:
Yes, those items match up with my response. Lee K5DAT
|
|
Re: Need Advice: MAP through an Internet T-Mobile, Verizon, etc. "can"
?
?
The TCP-MASTER goes on the node that you have no real control over. WW2BSA-5
TCP-MASTER goes in WW2BSA-5 and TCP-SLAVE goes in WW2BSA-7
?
You will nedd to port forward port 10200, protocol TCP at WW2BSA-7
?
--
73,
Mark, N5MDT
Montgomery, Texas
?
?
? |
|
Re: RIGCONTROL format/options
On Thu, Feb 27, 2025 at 03:35 PM, Robert Cartier wrote:
I see when I set it to 5 you can see the mode switch every 5 seconds between usb and USB-D If you are not scanning you can comment out the scan lines.? Then manually set your radio to the frequency and mode desired.? It will never change.
?
As long as you are scanning it will switch between data and not.
?
And John mentioned PTT_SETS_INPUT.? On my install I need that because I have both Pactor and Vara ports.? Do you have any hardware TNC ports?? If not you should be able to use PTT CAT or PTT CI-V instead and it may minimize or eliminate switching between modes like that.? In the end, whatever works for you...
?
--
73,
Mark, N5MDT
Montgomery, Texas
?
?
? |
|
Re: Route Sorting
开云体育
Nice tool. Nice work. I'll be interested to have a copy if avail for distribution. Thanks, Jean On 2025-02-28 05:43, Ray Adkins via
groups.io wrote:
|
|
Re: Route Sorting
I like it, it will let me know which links are having issues an can better keep track. On Sat, Feb 15, 2025, 9:01 AM John G8BPQ via <john.wiseman=[email protected]> wrote:
|
|
Re: RIGCONTROL format/options
开云体育You can send RADIO commands from the node or a BBS forwarding script.Can't you just leave the radio in USB-D? 73, John On 27/02/2025 21:35, Robert Cartier via
groups.io wrote:
thanks but without the PTT_SETS_INPUT my radio stays in USB and not USB-D and I get no signal to the internal card of the 7300 |
|
Re: BPQ - VARA
The VARA TNC? only supports listening for up to 5 callsigns. I'm a bit surprised you got 6 to work. VARA displays the calls it is listening for on the title bar.
toggle quoted message
Show quoted text
73, John On 28/02/2025 03:26, John - wb4moz via groups.io wrote:
We are in the process of creating a new node which has a VARA port. This is working for outgoing connects and some incoming connects. We have a total of 11 applications, each using a different ssid of the node call. |
|
Looking for Chat and Node connection partner for BBS forwarding
Hi All...
I have a few partners that have helped me out, but would like to establish a few more in the south east gulf coast area. Looking to expand coverage towards Georgia. I'm still fairly new, but have learned a lot from some key players here in the BPQ chat here.
?
Thanks,
John - KD6CLO |
|
BPQ - VARA
We are in the process of creating a new node which has a VARA port. This is working for outgoing connects and some incoming connects. We have a total of 11 applications, each using a different ssid of the node call.
It appears that only the node call and the first 5 applications are made available to VARA for incoming connects. The node call is WX4MC-8 RMS is temporary using WX4MC-14 - this will change to -10 when the node replaces the existing WX4MC-10. Attempting an incoming connect to WX4MC-14 (Application 6) or any higher application is denied by VARA. So, are we missing something? Is the limit actually 6 and how are they determined? Does MYCALLS allow more that 6?? Trying this did not work the first time.. Thanks? John WB4MOZ APPLICATION 1,BBS,,WX4MC,MCBBS,220 APPLICATION 2,OF1,C K4WOF-1,WX4MC-1,OF1,160 APPLICATION 3,WELL3,C WB4MOZ-3,WX4MC-2,160 APPLICATION 4,PKT8,C K4PKT-8,WX4MC-4,160 APPLICATION 5,OT2,C W4OT-2,WX4MC-5,160 APPLICATION 6,RMS,C 7 CMS,WX4MC-14,RMS,194 APPLICATION 7,RMS1,C W4SPR-10,WX4MC-6,SPRRMS,194 APPLICATION 8,RMS2,C KEWOF-10,WX4MC-7,WOFRMS,190 APPLICATION 9,RMS3,C?WB4MOZ-10,WX4MC-9,MOZRMS,190 APPLICATION 11,CHAT,,WX4MC-11,MCCHT,190 APPLICATION 12,PBC,,WX4MC-12,PBCCHT,190 |
|
Re: Need Advice: MAP through an Internet T-Mobile, Verizon, etc. "can"
Hello Chris, Assuming the gateway is located at the home site, the maps would look like this:
MAP WW2BSA-7 X.X.X.X
TCP-Master 10200 B ? ? ; home
MAP WW2BSA-5 0.0.0.0
TCP-Slave 10200 B????? ; Arts Center X.X.X.X is the public IP address at the Arts Center, and you can use a DNS name if you wish. The TCP-Slave map does not use a specific IP address - uses 0.0.0.0 The router at the Arts Center needs to port forward the TCP port to the BPQ host. If you use TCP 10200 as the examples show above, then port forward TCP 10200 to BPQ. I assumed the gateway is at home based on your choice of which map is the master vs. slave below. The bottom line is the TCP-Master map is applied at the site that has the "Can". 73, Lee K5DAT On Thu, Feb 27, 2025 at 5:43?PM Chris Lance WW2BSA via <Ww2bsa=[email protected]> wrote:
|
|
Need Advice: MAP through an Internet T-Mobile, Verizon, etc. "can"
I'm experimenting with one of my BPQ32 nodes. I need advice on how to MAP through a T-Mobile Arcadyan KVD21 Gateway. For only $35/mo it's a great way to provide internet service at almost any location - especially remote node sites.
1st experiment: MAP from my existing -7 node at the Arts Center to my -5 node at my house. I’ve been able to identify the IP address for the can and have had some success using the following format. (x's being the IP addresses) on -5:??? MAP WW2BSA-7 xxxxxxxxxxxx TCP-Master But before I go into a lengthy? post with more details, I wanted to first see how other Sysops have configured their MAP statements with a T-mobile, Verizon, etc. internet “can” if they use one. 73 de Chris |
|
Re: RIGCONTROL format/options
开云体育Thanks
Robert Cartier
kd1jg@... |
|
Re: RIGCONTROL format/options
开云体育thanks but without the PTT_SETS_INPUT my radio stays in USB and not USB-D and I get no signal to the internal card of the 7300I found that I need the following to get my setup to work Also since I am not currently scanning is their a way to set the frequency and not have it poll the radio I see when I set it to 5 you can see the mode switch every 5 seconds between usb and USB-D Thanks PORT ?PORTNUM=2 ?ID=HF VARA ?DRIVER=VARA ?INTERLOCK=1 ?PORTCALL=NNA1AH-10 ?CONFIG ?ADDR 127.0.0.1 8300 PTT CI-V PATH C:\VARA\VARA.exe ?APPL BBS ?BW2300 RIGCONTROL ?COM4 19200 ICOM 7300 94 PTT_SETS_INPUT ?99,4.9130,USB,D,F1 ?;5,7.3825,USB,D,F1 ? ?**** ENDPORT Robert Cartier kd1jg@...
Robert Cartier
kd1jg@... |
|
Re: Adding a command in bpgq32.cfg for vara hf and ic-7300
On 2/27/25 10:02, Robert Cartier via groups.io wrote:
Well ?I have bpq talking to vara HF ?. But unlike winlink express thereI use hamlib: RADIO 2 HAMLIB 10.78.196.104:4532 00:00 99,3.5957,USB-D,F1,D 11:59 99,7.101,USB-D,F1,D 17:00 99,14.102,USB-D,F1,D 20:00 99,7.101,USB-D,F1,D **** 3s, Chuck |
|
Re: RIGCONTROL format/options
开云体育This only applies if you are running a sound card modem and a hardware TNC on the same radio. If you only use VARA or other sound card modes you just set Data mode modulation source to USB and leave it there.PTT_SETS_INPUT is used to switch modulation source between AUX and USB if you have a Pactor TNC attached to the AUX port. 73, John On 27/02/2025 18:29, Robert Cartier via
groups.io wrote:
I found that the 7300 needs a little more commands to control the mode like USB-D |
|
RIGCONTROL format/options
开云体育I found that the 7300 needs a little more commands to control the mode like USB-Dcan someone explain the different options available. ?like P123, R1.. I assume R1 is for the radio number but I have to find a document that goes into more detail then the info below Supported Radios: Kenwood TS590S/SG ICOM IC7100 ICOM IC7200 ICOM IC7300 ICOM IC7410 ICOM IC7600 Yaesu FT991/991A If you are running a Sound Card Modem using the internal soundcard and PACTOR (or other TNC Modes) using the AUX connector the input to the modulator has to be changed depending on which is transmitting. As the Soundcard TNC sends PTT ON and PTT OFF commands to the application, these can be used to switch the input source. To enable this add PTT_SETS_INPUT to the RIGCONTROL config, eg RIGCONTROL COM8 19200 ICOM IC7100 88 PTT_SETS_INPUT ?6,14.110,usb,F1,d,P123,R1 ?6,28.110,usb,F1,d,P123,R1 **** THanks in advance Robert Cartier
kd1jg@... |
Ray Adkins
N3MEL - Glenn
to navigate to use esc to dismiss