Re: Kan 9612+ help #llinbpq

Sparks KK4IB

开云体育

Jim, Did you set the TNC into KISS mode? BPQ-32 does all the processing work.

sparks

On Jul 5, 2022, at 3:50 PM, Lee Bengston <kilo5dat@...> wrote:

I have a 9612+, and Ken's advice sounds good. When using the 1200b port, settings for software such as BPQ are usually the same that would apply to a KPC3+.? Channel=A should work fine. Also 9600 is probably best for the speed.

The TNCPORT section applies to the TNC Emulator feature, so applying the same serial port there may be causing a problem, but I'm not sure about that.

73,

Lee K5DAT?

On Tue, Jul 5, 2022, 2:16 PM Ken, W9GM <ken@...> wrote:

Hi Jim,
?
Remove the TNC Port section, and make sure you don’t just need an A or B for CHANNEL.? I know KAMs only need A or B,
but not familiar with the 9612.
?
If you had the speed at 4800 when you put the TNC is KISS, that should be good, but 9600 is more common.? I think older TNC’s
may on be good for 4800.
?
Give this a try.
?
73, Ken
W9GM
?
?
From: [email protected] [mailto:[email protected]] On Behalf Of Jim - KI0BK via
Sent: Tuesday, July 5, 2022 12:42 PM
To: [email protected]
Subject: [bpq32] Kan 9612+ help #llinbpq
?
a newbie here looking for help getting my first packet station running, I'm use linbpq on a rbpi3+, trying to get it to talk to my Kantronics
KPC9612+ TNC but not having any luck. I have a USB/RS232 dongle that shows up as ttyUSB0 and I can use terminal ok to talk to the
TNC when it is in normal command mode, but after switching it to kiss mode and trying to connect using bpq terminal, i get invalidstream
from the TNC. Hoping someone has this working and can help me figure out what I have done wrong.
here is a portion of my config file I think is involved:
TNCPORT????????????????????????????????????????? ; Host Port
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial connection (created by BPQ)
?? TYPE=KANT???????????????????????????????????? ; TNC2,KANT,SCS,DED
?? APPLNUM=32??????????????????????????????????? ; Last Application
?? APPLFLAGS=6?????????????????????????????????? ; Display Connected Message
ENDPORT

;? Port 1?
PORT
?? PORTNUM=1???????????????????????????????????? ; Port number
?? ID=145.090 MHz 1200 bps?????????????????????? ; PORTS command text
?? TYPE=ASYNC??????????????????????????????????? ; RS232 connection
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial port
?? FULLDUP=0???????????????????????????????????? ;
?? SPEED=4800??????????????????????????????????? ; Serial port speed
?? PROTOCOL=KISS???????????????????????????????? ; KISS protocol
?? ;KISSOPTIONS=POLLED,ACKMODE,NOPARAMS??????????????????? ; KISS options for TNC
?? CHANNEL=1A??????????????????????????????????? ; TNC channel
?? MAXFRAME=2??????????????????????????????????? ; Max outstanding frames
?? FRACK=7000??????????????????????????????????? ; Level 2 timeout (ms)
?? RESPTIME=1000???????????????????????????????? ; Level 2 delayed ACK (ms)
?? RETRIES=10??????????????????????????????????? ; Level 2 max retries
?? PACLEN=128??????????????????????????????????? ; Max packet length (bytes)
?? TXDELAY=500?????????????????????????????????? ; Transmit keyup delay (ms)
?? SLOTTIME=100????????????????????????????????? ; CMSA interval timer (ms)
?? PERSIST=64??????????????????????????????????? ; Persistence (256/(# transmissions-1)

Hope some one can help.
73
Jim KI0BK

Re: Kan 9612+ help #llinbpq

#35455

I have a 9612+, and Ken's advice sounds good. When using the 1200b port, settings for software such as BPQ are usually the same that would apply to a KPC3+.? Channel=A should work fine. Also 9600 is probably best for the speed.

The TNCPORT section applies to the TNC Emulator feature, so applying the same serial port there may be causing a problem, but I'm not sure about that.

73,

Lee K5DAT?

Show quoted text

On Tue, Jul 5, 2022, 2:16 PM Ken, W9GM <ken@...> wrote:

Hi Jim,
?
Remove the TNC Port section, and make sure you don’t just need an A or B for CHANNEL.? I know KAMs only need A or B,
but not familiar with the 9612.
?
If you had the speed at 4800 when you put the TNC is KISS, that should be good, but 9600 is more common.? I think older TNC’s
may on be good for 4800.
?
Give this a try.
?
73, Ken
W9GM
?
?
From: [email protected] [mailto:[email protected]] On Behalf Of Jim - KI0BK via
Sent: Tuesday, July 5, 2022 12:42 PM
To: [email protected]
Subject: [bpq32] Kan 9612+ help #llinbpq
?
a newbie here looking for help getting my first packet station running, I'm use linbpq on a rbpi3+, trying to get it to talk to my Kantronics
KPC9612+ TNC but not having any luck. I have a USB/RS232 dongle that shows up as ttyUSB0 and I can use terminal ok to talk to the
TNC when it is in normal command mode, but after switching it to kiss mode and trying to connect using bpq terminal, i get invalidstream
from the TNC. Hoping someone has this working and can help me figure out what I have done wrong.
here is a portion of my config file I think is involved:
TNCPORT????????????????????????????????????????? ; Host Port
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial connection (created by BPQ)
?? TYPE=KANT???????????????????????????????????? ; TNC2,KANT,SCS,DED
?? APPLNUM=32??????????????????????????????????? ; Last Application
?? APPLFLAGS=6?????????????????????????????????? ; Display Connected Message
ENDPORT

;? Port 1?
PORT
?? PORTNUM=1???????????????????????????????????? ; Port number
?? ID=145.090 MHz 1200 bps?????????????????????? ; PORTS command text
?? TYPE=ASYNC??????????????????????????????????? ; RS232 connection
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial port
?? FULLDUP=0???????????????????????????????????? ;
?? SPEED=4800??????????????????????????????????? ; Serial port speed
?? PROTOCOL=KISS???????????????????????????????? ; KISS protocol
?? ;KISSOPTIONS=POLLED,ACKMODE,NOPARAMS??????????????????? ; KISS options for TNC
?? CHANNEL=1A??????????????????????????????????? ; TNC channel
?? MAXFRAME=2??????????????????????????????????? ; Max outstanding frames
?? FRACK=7000??????????????????????????????????? ; Level 2 timeout (ms)
?? RESPTIME=1000???????????????????????????????? ; Level 2 delayed ACK (ms)
?? RETRIES=10??????????????????????????????????? ; Level 2 max retries
?? PACLEN=128??????????????????????????????????? ; Max packet length (bytes)
?? TXDELAY=500?????????????????????????????????? ; Transmit keyup delay (ms)
?? SLOTTIME=100????????????????????????????????? ; CMSA interval timer (ms)
?? PERSIST=64??????????????????????????????????? ; Persistence (256/(# transmissions-1)

Hope some one can help.
73
Jim KI0BK

Re: Kan 9612+ help #llinbpq

#35454

开云体育

Hi Jim,

?

Remove the TNC Port section, and make sure you don’t just need an A or B for CHANNEL.? I know KAMs only need A or B,

but not familiar with the 9612.

?

If you had the speed at 4800 when you put the TNC is KISS, that should be good, but 9600 is more common.? I think older TNC’s

may on be good for 4800.

?

Give this a try.

?

73, Ken

W9GM

?

Show quoted text

From: [email protected] [mailto:[email protected]] On Behalf Of Jim - KI0BK via groups.io
Sent: Tuesday, July 5, 2022 12:42 PM
To: [email protected]
Subject: [bpq32] Kan 9612+ help #llinbpq

?

a newbie here looking for help getting my first packet station running, I'm use linbpq on a rbpi3+, trying to get it to talk to my Kantronics
KPC9612+ TNC but not having any luck. I have a USB/RS232 dongle that shows up as ttyUSB0 and I can use terminal ok to talk to the
TNC when it is in normal command mode, but after switching it to kiss mode and trying to connect using bpq terminal, i get invalidstream
from the TNC. Hoping someone has this working and can help me figure out what I have done wrong.
here is a portion of my config file I think is involved:
TNCPORT????????????????????????????????????????? ; Host Port
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial connection (created by BPQ)
?? TYPE=KANT???????????????????????????????????? ; TNC2,KANT,SCS,DED
?? APPLNUM=32??????????????????????????????????? ; Last Application
?? APPLFLAGS=6?????????????????????????????????? ; Display Connected Message
ENDPORT

;? Port 1?
PORT
?? PORTNUM=1???????????????????????????????????? ; Port number
?? ID=145.090 MHz 1200 bps?????????????????????? ; PORTS command text
?? TYPE=ASYNC??????????????????????????????????? ; RS232 connection
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial port
?? FULLDUP=0???????????????????????????????????? ;
?? SPEED=4800??????????????????????????????????? ; Serial port speed
?? PROTOCOL=KISS???????????????????????????????? ; KISS protocol
?? ;KISSOPTIONS=POLLED,ACKMODE,NOPARAMS??????????????????? ; KISS options for TNC
?? CHANNEL=1A??????????????????????????????????? ; TNC channel
?? MAXFRAME=2??????????????????????????????????? ; Max outstanding frames
?? FRACK=7000??????????????????????????????????? ; Level 2 timeout (ms)
?? RESPTIME=1000???????????????????????????????? ; Level 2 delayed ACK (ms)
?? RETRIES=10??????????????????????????????????? ; Level 2 max retries
?? PACLEN=128??????????????????????????????????? ; Max packet length (bytes)
?? TXDELAY=500?????????????????????????????????? ; Transmit keyup delay (ms)
?? SLOTTIME=100????????????????????????????????? ; CMSA interval timer (ms)
?? PERSIST=64??????????????????????????????????? ; Persistence (256/(# transmissions-1)

Hope some one can help.
73
Jim KI0BK

Kan 9612+ help #llinbpq

#35453

a newbie here looking for help getting my first packet station running, I'm use linbpq on a rbpi3+, trying to get it to talk to my Kantronics
KPC9612+ TNC but not having any luck. I have a USB/RS232 dongle that shows up as ttyUSB0 and I can use terminal ok to talk to the
TNC when it is in normal command mode, but after switching it to kiss mode and trying to connect using bpq terminal, i get invalidstream
from the TNC. Hoping someone has this working and can help me figure out what I have done wrong.
here is a portion of my config file I think is involved:
TNCPORT????????????????????????????????????????? ; Host Port
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial connection (created by BPQ)
?? TYPE=KANT???????????????????????????????????? ; TNC2,KANT,SCS,DED
?? APPLNUM=32??????????????????????????????????? ; Last Application
?? APPLFLAGS=6?????????????????????????????????? ; Display Connected Message
ENDPORT

;? Port 1?
PORT
?? PORTNUM=1???????????????????????????????????? ; Port number
?? ID=145.090 MHz 1200 bps?????????????????????? ; PORTS command text
?? TYPE=ASYNC??????????????????????????????????? ; RS232 connection
?? COMPORT=/dev/ttyUSB0????????????????????????? ; Serial port
?? FULLDUP=0???????????????????????????????????? ;
?? SPEED=4800??????????????????????????????????? ; Serial port speed
?? PROTOCOL=KISS???????????????????????????????? ; KISS protocol
?? ;KISSOPTIONS=POLLED,ACKMODE,NOPARAMS??????????????????? ; KISS options for TNC
?? CHANNEL=1A??????????????????????????????????? ; TNC channel
?? MAXFRAME=2??????????????????????????????????? ; Max outstanding frames
?? FRACK=7000??????????????????????????????????? ; Level 2 timeout (ms)
?? RESPTIME=1000???????????????????????????????? ; Level 2 delayed ACK (ms)
?? RETRIES=10??????????????????????????????????? ; Level 2 max retries
?? PACLEN=128??????????????????????????????????? ; Max packet length (bytes)
?? TXDELAY=500?????????????????????????????????? ; Transmit keyup delay (ms)
?? SLOTTIME=100????????????????????????????????? ; CMSA interval timer (ms)
?? PERSIST=64??????????????????????????????????? ; Persistence (256/(# transmissions-1)

Hope some one can help.
73
Jim KI0BK

Re: QtTermTCP crashing

#35452

I guess that's progress!

Thanks
John

Show quoted text

On 05/07/2022 15:52, Sholto Fisher wrote:
* can't

On 7/5/2022 9:51 AM, Sholto Fisher wrote:
John,

I can get this version to crash either.

Sholto

On 7/5/2022 9:03 AM, John G8BPQ wrote:
There is something odd going on here. I can't get it to fail myself, but another station was having the same problem. He tried running a debug version for me, but it didn't crash. So can you try that version?

Thanks,
John

On 03/07/2022 16:56, Sholto Fisher wrote:
John,

It's when someone makes a connection that's handled by this in the bpq config.

APPLICATION 3,TALK,att 3 127.0.0.1 8015,K7TMG,,255

A new terminal window appears in QTtermTCP and sometimes it will crash immediately, sometimes I can chat for a while and upon closing the terminal window QtTermTCP will crash.

Sholto

On 7/3/2022 12:52 AM, John G8BPQ wrote:
Sholto,

Which popup window are you referring to?

73,
John

On 02/07/2022 21:21, Sholto Fisher wrote:
John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Re: QtTermTCP crashing

#35451

* can't

Show quoted text

On 7/5/2022 9:51 AM, Sholto Fisher wrote:
John,
I can get this version to crash either.
Sholto
On 7/5/2022 9:03 AM, John G8BPQ wrote:
There is something odd going on here. I can't get it to fail myself, but another station was having the same problem. He tried running a debug version for me, but it didn't crash. So can you try that version?



Thanks,
John

On 03/07/2022 16:56, Sholto Fisher wrote:
John,

It's when someone makes a connection that's handled by this in the bpq config.

APPLICATION 3,TALK,att 3 127.0.0.1 8015,K7TMG,,255

A new terminal window appears in QTtermTCP and sometimes it will crash immediately, sometimes I can chat for a while and upon closing the terminal window QtTermTCP will crash.

Sholto

On 7/3/2022 12:52 AM, John G8BPQ wrote:
Sholto,

Which popup window are you referring to?

73,
John


On 02/07/2022 21:21, Sholto Fisher wrote:
John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Re: QtTermTCP crashing

#35450

John,

I can get this version to crash either.

Sholto

Show quoted text

On 7/5/2022 9:03 AM, John G8BPQ wrote:
There is something odd going on here. I can't get it to fail myself, but another station was having the same problem. He tried running a debug version for me, but it didn't crash. So can you try that version?

Thanks,
John
On 03/07/2022 16:56, Sholto Fisher wrote:
John,

It's when someone makes a connection that's handled by this in the bpq config.

APPLICATION 3,TALK,att 3 127.0.0.1 8015,K7TMG,,255

A new terminal window appears in QTtermTCP and sometimes it will crash immediately, sometimes I can chat for a while and upon closing the terminal window QtTermTCP will crash.

Sholto

On 7/3/2022 12:52 AM, John G8BPQ wrote:
Sholto,

Which popup window are you referring to?

73,
John


On 02/07/2022 21:21, Sholto Fisher wrote:
John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Re: QtTermTCP crashing

#35449

There is something odd going on here. I can't get it to fail myself, but another station was having the same problem. He tried running a debug version for me, but it didn't crash. So can you try that version?

Thanks,
John

Show quoted text

On 03/07/2022 16:56, Sholto Fisher wrote:
John,

It's when someone makes a connection that's handled by this in the bpq config.

APPLICATION 3,TALK,att 3 127.0.0.1 8015,K7TMG,,255

A new terminal window appears in QTtermTCP and sometimes it will crash immediately, sometimes I can chat for a while and upon closing the terminal window QtTermTCP will crash.

Sholto

On 7/3/2022 12:52 AM, John G8BPQ wrote:
Sholto,

Which popup window are you referring to?

73,
John

On 02/07/2022 21:21, Sholto Fisher wrote:
John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Re: forwarding partners

#35448

Same here. HF or AXUDP?

73, Todd N7TRY

Show quoted text

On Mon, Jul 4, 2022 at 11:39 AM Jerry Kutche <n9lya@...> wrote:

Hello.
?What mode?
Hf or axudp? ..
73 jerry n9lya

-------- Original message --------
From: guy lemke <guy@...>
Date: 7/4/22 1:20 PM (GMT-05:00)
To: [email protected]
Subject: [bpq32] forwarding partners

looking for forwarding partners for both my bbs (KD6MTU) and the WARREA club bbs (KE6CHO) ...?

Guy kd6mtu

Re: forwarding partners

#35447

开云体育

Hello.

?What mode?

Hf or axudp? ..

73 jerry n9lya

Show quoted text

-------- Original message --------

From: guy lemke <guy@...>

Date: 7/4/22 1:20 PM (GMT-05:00)

To: [email protected]

Subject: [bpq32] forwarding partners

looking for forwarding partners for both my bbs (KD6MTU) and the WARREA club bbs (KE6CHO) ...?

Guy kd6mtu

Re: forwarding partners

#35446

sorry forgot to put contact info

kd6mtu@...

forwarding partners

#35445

looking for forwarding partners for both my bbs (KD6MTU) and the WARREA club bbs (KE6CHO) ...?

Guy kd6mtu

Re: QtTermTCP crashing

Richard Hendricks - KE0GB

#35444

Sholto:

I use APPLICATION 32 instead of 3, and don't have any issues.? You might want to give that a try.

73 - Rick

Re: QtTermTCP crashing

#35443

John,

It's when someone makes a connection that's handled by this in the bpq config.

APPLICATION 3,TALK,att 3 127.0.0.1 8015,K7TMG,,255

A new terminal window appears in QTtermTCP and sometimes it will crash immediately, sometimes I can chat for a while and upon closing the terminal window QtTermTCP will crash.

Sholto

Show quoted text

On 7/3/2022 12:52 AM, John G8BPQ wrote:
Sholto,
Which popup window are you referring to?
73,
John
On 02/07/2022 21:21, Sholto Fisher wrote:
John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Change the APRS object symbol with the OBJECT PATH argument.

#35442

Hi,

I have?this configuration inside the OBJECT PATH argument:

OBJECT PATH=APRS,WIDE1-1 PORT=1,IS INTERVAL=20 TEXT=CT1FGS-3*111111z3845.79N/00912.06WPacket BBS CT1FGS-2. Telnet

APRS displays a Police Car (/p) symbol with this APRS object format, even i didn't define any symbol.

How can I define the? symbol for each object i add,?inside the bpq32.cfg??

Thank you,
73 de Nuno
CT1FGS

Re: QtTermTCP crashing

#35441

Sholto,

Which popup window are you referring to?

73,
John

Show quoted text

On 02/07/2022 21:21, Sholto Fisher wrote:
John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Re: Filtering node table

#35440

N *BP* already works, as does ??bp*:

n *bp*

POGO4:G8BPQ-9} Nodes

BPQBBS:G8BPQ-3 BPQCHT:GM8BPQ-4 BPQDX:G8BPQ-11 CASLGR:VA7RBP-7

NOTCHT:G8BPQ-4 POGO:GM8BPQ-9 RBPBBS:VA7RBP-2

?

n ??bp*

POGO4:G8BPQ-9} Nodes

BPQBBS:G8BPQ-3 BPQDX:G8BPQ-11 NOTCHT:G8BPQ-4

The next version will search both aliases and calls. The C in the command selects the sort order of the display (sort by call instead of the default sort by alias)

73,
John

On Thu, Jun 30, 2022 at 08:20 AM, Julian wrote:

Show quoted text

Hi agn John. It would be great if you could enhance that search to either side of the string, N C *BPQ, N C *BP* etc. Also on aliases, possibly a N A *XYZ etc etc.?
Thnx.
Regards, J, M 0 IPU, YO 3 FCA.?

QtTermTCP crashing

#35439

John,

I use the tcp port listener in QtTermTCP and had no issues with the old 0.0.0.48 version but 53c and 54 both will randomly crash if a connection is made, sometimes upon opening, sometimes on closing the popup window.

This is on Windows 10. I'm using the MDI interface.

Sholto
K7TMG

Re: BPQ32 IP Gateway to a PiLinBPQ System

#35438

44.135.101.1 is the IPGateway on VE3KPG running BPQ32
44.135.101.2 is VA3HIP running PiLinBPQ

I am unable to ping 44.135.101.2 as well. In fact, I cannot ping any addresses other than 44.135.101.1, but NAT and IPR does seem to be working.

nat

PETERB:VE3KPG-2}?

44.135.101.2 to 192.168.1.9

44.135.101.1 to 192.168.1.10

?

ping 44.135.101.1

PETERB:VE3KPG-2}?

OK

Ping Response from 44.135.101.1

?

ping 44.135.101.2

PETERB:VE3KPG-2}?

OK

?

ping 44.131.56.2

PETERB:VE3KPG-2}?

OK

?

ping 44.92.35.1

PETERB:VE3KPG-2}?

OK

?

ipr

PETERB:VE3KPG-2} 765 Entries

44.0.0.0/9 0 T 0 0 encap 169.228.34.84

44.0.0.1/32 0 T 1 3355 encap 169.228.34.84

44.2.0.2/32 0 T 1 3355 encap 98.20.210.138..........etc..

This is what I have for my IPGateway on VE3KPG;

IPGATEWAY

Adapter \Device\NPF_{EA2D9183-0C8D-4AB0-BD03-AEA6D347354B}? ? ? ? ; See Below Description

44ENCAP 192.168.1.250? ? ? ? ? ? ? ? ? ? ? ; This is a Un-used but inside of routers DHCP (Must be added to routers DMZ)

IPAddr 44.135.101.1? ? ? ? ? ? ? ? ? ? ? ? ? ? ?; Your 44 AMPR IP

IPNetMask 255.255.255.248? ? ? ? ? ? ? ? ; The 248 (last 3) depends on how many IP addresses you have, mine is 8 IP’S

IPPorts 1? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?; Port Numbers to be used, 2 is my AXIP 3 My Telnet port

NAT 44.135.101.2 192.168.1.9? ? ? ? ? ? ?;VA3HIP running PiLinBPQ

ROUTE 44.0.0.0/9 169.228.34.84 T? ? ?; This Line and following line is needed to access the AMPR Portal Web Site

ROUTE 44.128.0.0/10 169.228.34.84 T

**** ; End of Config

This what is setup on VA3HIP;

IPGATEWAY

IPAddr 44.135.101.2? ? ? ? ? ? ? ? ? ? ? ? ?; VA3HIP

IPNetMask 255.255.255.248? ? ? ? ? ? ; The 248 (last 3) depends on how many IP addresses you have, mine is 8 IP’S

IPPorts 1? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ; Port Numbers to be used, 2 is my AXIP 3 My Telnet port

**** ; End of Config

Should I be able to ping any IP address including 44 AMPRNet?

Re: BPQ32 IP Gateway to a PiLinBPQ System

#35437

开云体育

At the moment I can ping 44.135.101.1 over the IPIP tunnel, but not 44.135.101.2. What is 44.135.101.1?

LinBPQ will add a NAT entry from 44.135.101.2 to the IP address of the machine running LinBPQ.

To allow access from 44 net? to other machines on the same network you need to allocate another address in your 44.35.1.101 range to each and add NAT lines. For example I have

?NAT 44.131.56.2 192.168.1.35
?NAT 44.131.56.4 192.168.1.64
?NAT 44.131.56.5 192.168.1.118
?NAT 44.131.56.6 192.168.1.254

My IPADDR is 44.131.56.7 and the linbpq pi is 192.168.1.44, so I end up with

nat

POGO4:G8BPQ-9}

44.131.56.2 to 192.168.1.35

44.131.56.4 to 192.168.1.64

44.131.56.5 to 192.168.1.118

44.131.56.6 to 192.168.1.254

44.131.56.7 to 192.168.1.44 via TAP

ping 44.131.56.4

POGO4:G8BPQ-9}

OK

Ping Response from 44.131.56.4

73,

John

On 01/07/2022 22:47, Harmen Minnema wrote:

Show quoted text

Will? adding the NAT 44.135.101.2? 192.168.9 line into IP Gateway settings on my BPQ32 system allow outside connections to a PiLinBPQ system on the same network?

Also added the following to IPGatway Settings in PiLinBPQ system;
IPAddr 44.135.101.2
IPNetmast 255.255.255.248
IPPorts 1

If so, are there IP Gateway settings required for the PiLinBPQ system?? Haven't been able to get it to work....

Thanks,
Harmen VE3EMA