I don't know,? I will need some time to set up and test here.
On Friday, April 4, 2025 at 12:09:14 a.m. EDT, Kerem Kapkin via groups.io <kkapkin@...> wrote:
When I use the instructions on page 24, Examine Input Port, Press 5 12, read in12 78, instead I am getting blinking FF. Is this normal? Does this indicate in have an HW problem?
|
Re: Testing the piezo speaker
It can be activated through software, but I don't recall if the firmware made that available.?
On Monday, April 7, 2025 at 12:56:52 p.m. EDT, Mitch Smith via groups.io <kb3gkc@...> wrote:
Yes, it actually beeps on each key press. I just couldn't hear it.
Is there anything else I can do with it?
Mitch
|
Re: Testing the piezo speaker
Thanks Kerem, I’ll give that a try.?
Paul
It is louder if the Piezo speaker is not in contact with the chips below, and suspended in the air with the ground wires.
<IMG_8573.jpeg>
I have the same problem.? If I put my ear to it I can hear a faint beep.? Checked all the wiring and connections, everything looks right.
Paul
Yes, it actually beeps on each key press. I just couldn't hear it.
Is there anything else I can do with it?
Mitch
?
?
?
|
Re: Testing the piezo speaker
It is louder if the Piezo speaker is not in contact with the chips below, and suspended in the air with the ground wires.
I have the same problem.? If I put my ear to it I can hear a faint beep.? Checked all the wiring and connections, everything looks right.
Paul
On Apr 7, 2025 at 12:56?PM -0400, Mitch Smith via <kb3gkc= gmail.com@groups.io>, wrote:
Yes, it actually beeps on each key press. I just couldn't hear it.
Is there anything else I can do with it?
Mitch
|
Re: Testing the piezo speaker
I have the same problem. ?If I put my ear to it I can hear a faint beep. ?Checked all the wiring and connections, everything looks right.
Paul
On Apr 7, 2025 at 12:56?PM -0400, Mitch Smith via groups.io <kb3gkc@...>, wrote:
Yes, it actually beeps on each key press. I just couldn't hear it.
Is there anything else I can do with it?
Mitch
|
Re: Testing the piezo speaker
Yes, it actually beeps on each key press. I just couldn't hear it.
Is there anything else I can do with it?
Mitch
|
Re: Testing the piezo speaker
Each key press creates a beep as well as turns on the led. If you don’t hear a beep, I would check to see if the opto coupler is installed?correctly.
I finally added the piezo speaker to the Z80MC. It only took me 2 years!
What I'd like to know is how is the speaker accessed?
I half expected there to be a beep or something when the system booted up but I didn't hear anything.
Is there a way I can test the speaker?
Short assembly or basic program maybe?
I looked in the monitor code but I couldn't find anything other than the "beep" LED.
Thanks for the help.
Mitch
|
Testing the piezo speaker
I finally added the piezo speaker to the Z80MC. It only took me 2 years!
What I'd like to know is how is the speaker accessed?
I half expected there to be a beep or something when the system booted up but I didn't hear anything.
Is there a way I can test the speaker?
Short assembly or basic program maybe?
I looked in the monitor code but I couldn't find anything other than the "beep" LED.
Thanks for the help.
Mitch
|
Re: Strange behavior of #8 button
I just did the same thing. Added a 22k resistor to R4 pins 1-2.
Since my problem was intermittent, I'm hoping this resolves the issue.
Mitch
|
Removed the SIO card, now I am getting in12 78 Is it possible that the SIO card interfering with input port 12? SIO card is a new one, assembled with great caution and seem to be working fine, except this test case. I will have to replace all the ICs on the first one to recover, hopefully.
When I use the instructions on page 24, Examine Input Port, Press 5 12, read in12 78, instead I am getting blinking FF. Is this normal? Does this indicate in have an HW problem?
|
When I use the instructions on page 24, Examine Input Port, Press 5 12, read in12 78, instead I am getting blinking FF. Is this normal? Does this indicate in have an HW problem?
|
Re: Strange behavior of #8 button
The comment on TTL was a generalization.
?
Also likely any Nmos chips and others will be dead.
That will include most of the parts like the Ram chip, uSD is
plugged in, and as mentioned already most likely all of the ttl.
?
There is nothing more than a few diodes and prebiased
transistors that are designed to survive more than 6V on
that board.
?
I know this as I had a system I'd built (about 30 years ago)
die when a linear power supply failed (shorted pass transistor)
and went to 9-10V.? Killed all 95 pieces of TTL, ram, four 2901
bit slice, and even eprom.? The replaced supply had crowbar
over voltage protection.
?
?
Allison
|
Re: Strange behavior of #8 button
Thanks Allison. I have replaced the 74SL259 with a new one, but didn’t make any difference.
Any TTL (74LS259) will react very badly with overvoltage.
Most of the CMOS may tolerate it.
?
?
Allison
|
Re: Strange behavior of #8 button
Any TTL (74LS259) will react very badly with overvoltage.
Most of the CMOS may tolerate it.
?
?
Allison
|
Re: Strange behavior of #8 button
Now that the Front Panel is working, I need to fix the SIO card which I think accidentally destroyed during the troubleshooting of the Front Panel. SIO card received 9V instead of 5V now all LEDs are on and no response from the board. So I am guessingthat I fried the 74LS259 bit latch which has a max Vcc 5.5 unlike the 74HC, and directly connected to the LEDs. Next would be to replace 74LS01, however I only have a 74LS03 that won’t work.?
|
Re: Strange behavior of #8 button
I originally used FJN3303 transistors, which have internal 22k+22k resistors. When Mouser stopped stocking the thru-hole versions, I had to switch to FJN3305 with internal 4.7k+10k resistors. I *thought* they worked OK. Obviously I was wrong!
?
Since then, I bought some FJN3304 transistors with 47k+47k for my 1802MC. I'm going to try them in the Z80MC Front Panel to see if they are a better choice. If so, it's an easy change. :-)
?
(An aside: Lots of manufacturers still make these pre-biased transistors. But a) they don't provide thru-hole versions any more, and b) instead of assigning 2Nxxxx numbers to facilitate 2nd sources, they hide them under house numbers.)
?
Lee
--
Excellence does not require perfection. -- Henry James
But it *does* require attention to detail! -- Lee Hart
--
Lee A. Hart
|
Re: Strange behavior of #8 button
Hi all!
?
To add another data point to the problem, I'm using DTC114ES for Q2/Q3, and DTA114ES for Q5 (all with 10k + 10k resistors) and R4 is 22k.?
?
Edit:? R4 is of course 10k.? I confused it with R4 on the processor board.? Sorry for any confusion!
?
I've never had any problems with button 8, or anything else for that matter.
?
Good luck,
Mike
?
|
Re: Strange behavior of #8 button
Thanks Lee, a 22K resistor in parallel with R4 A between pins 1 and 2 solved the problem with S8.
Kerem Kapkin wrote:
> Here is the recommended setup for standalone testing of the front panel...
> J2 Pin 9 [/out] connected to 3 components. 0.1uF cap other end ground,
> momentary switch other end ground,
> 100K resistor other end Vcc(5V).
?
Correct. This provides a debounced pushbutton to clock counter U2A.
?
> J2 Pin 24 -CLOCK- high (Vcc) or low (Ground)
?
Either is fine; you just don't want to leave a CMOS input floating.
?
> P1 pin 1 ground to (-) power supply
?
Or J2 pin 10 also works.
?
> J2 Pin 19 Vcc to +5V power supply
?
With this setup, you can step counter U2A through its states 0-7. Each state is output on J2 pins 11, 12, and 13. Each state should set the corresponding output of U3 low so you can test each button.
?
I think I see the problem with the "8" key! When U3 output C0 is low, IN4 (J2 pin 15) should be high. But transistor Q3 is also connected to C0. It is a "pre-biased" FJN3305, which has internal 10k and 4.7k resistors between its base and emitter. Its emitter ties to C0, and its base to R1D, a 1.5K to ground.These three resistors (10K + 4.7K + 1.5K = 16.2K) are pulling C0 low despite 18K R4A trying to pull it high! Thus the "halfway between" logic level, on IN4.
?
I'm busy preparing for VCF-East right now, but will confirm this when I return. In the meantime, I'll bet putting a lower value resistor (like 1.5K) in parallel between R4A pins 1-2 will fix the problem.
Lee
--
Excellence does not require perfection. -- Henry James
But it *does* require attention to detail! -- Lee Hart
--
Lee A. Hart
|
Re: Strange behavior of #8 button
Kerem Kapkin wrote:
> Here is the recommended setup for standalone testing of the front panel...
> J2 Pin 9 [/out] connected to 3 components. 0.1uF cap other end ground,
> momentary switch other end ground,
> 100K resistor other end Vcc(5V).
?
Correct. This provides a debounced pushbutton to clock counter U2A.
?
> J2 Pin 24 -CLOCK- high (Vcc) or low (Ground)
?
Either is fine; you just don't want to leave a CMOS input floating.
?
> P1 pin 1 ground to (-) power supply
?
Or J2 pin 10 also works.
?
> J2 Pin 19 Vcc to +5V power supply
?
With this setup, you can step counter U2A through its states 0-7. Each state is output on J2 pins 11, 12, and 13. Each state should set the corresponding output of U3 low so you can test each button.
?
I think I see the problem with the "8" key! When U3 output C0 is low, IN4 (J2 pin 15) should be high. But transistor Q3 is also connected to C0. It is a "pre-biased" FJN3305, which has internal 10k and 4.7k resistors between its base and emitter. Its emitter ties to C0, and its base to R1D, a 1.5K to ground.These three resistors (10K + 4.7K + 1.5K = 16.2K) are pulling C0 low despite 18K R4A trying to pull it high! Thus the "halfway between" logic level, on IN4.
?
I'm busy preparing for VCF-East right now, but will confirm this when I return. In the meantime, I'll bet putting a lower value resistor (like 1.5K) in parallel between R4A pins 1-2 will fix the problem.
Lee
--
Excellence does not require perfection. -- Henry James
But it *does* require attention to detail! -- Lee Hart
--
Lee A. Hart
|
Re: Strange behavior of #8 button
Here is the recommended setup for standalone testing of the front panel, just to make sure it is the correct start. -J2 Pin 9 [/out] is connected to 3 components. 0.1uF cap other end ground, momentary switch other end ground, 100K resistor other end Vcc(5V). Original recommendation was to use J2 Pin 8, however (b)TTL option that pin is not connected to anything but P1 TX 5. -J2 Pin 24 -CLOCK- high (Vcc) or low (Ground) -P1 1 ground to (-) power supply -J2 P19 Vcc to +5V power supply
> I cannot get S8 work no matter what. While running FFF1 sequence it is using 92mA current at 5V supply.
?
OK, that's correct. You have enough 5v power.
?
> While testing with the logic probe, 74LS145 inputs to A(15), B(14) and C(13) are fine but D(12) is always LOW.
?
That's also correct. 74LS145 input D (pin 12) is always low when the interrupt handler is working. The inputs to it count from 0-7 and repeat. If the Z80 interrupt handler fails to respond to the keyboard/display interrupt, then input D (pin 12) goes high to disable the LED display and keypad.
?
As I described earlier, you can test the Front Panel by itself, without the CPU board. You should be able to set the A B C inputs of the 74LS145 (with the 74HC393 counter) to each of the 8 states, then operate each keypad key in turn, and see the IN bits identify which key you pressed.
?
Lee
?
I am using the (b) TTL configuration both on the Z80 card as well as the Front panel.
--
Excellence does not require perfection. -- Henry James
But it *does* require attention to detail! -- Lee Hart
--
Lee A. Hart
|
Kerem Kapkin
Lee Hart