开云体育

hi Fred, Thank you so much for your kindness. I am in the electronics business and I can print my own PCBs if required, and I can work from a schematic. So no problems handling whatever you can throw

Alan, I have a modified FTV-901R as well as the cable and mod instruction sheet. The ALC Board in the transverter is replaced by one which takes a different drive level and there are changes

hi guys, I have bought this transverter to use with my FT980 and I have seen mention in this group that there is a mod that can be done to it to make it work with the FT980 but my enquiries qith

I forgot: the base for the FLLs in the FT-980 is actually 10Hz, not 1Hz. So ... and 80Hz error would be 2^3 (= 8) * 10Hz. Could be a coincidence ... but maybe check out the drive and diode on the 3rd

Thank you. I guess I’ll have to put on my engineering hat and dig deeper.

The FT-980 clock structure is very elegant (w/ error canceling technique s and such not) ... but also complicated. Fortunately you've identified some clues: 1. Happens in SSB (USB & LSB) but not

I am curious if there is an adjustment to correct the issue described below. In CW or AM, according to my frequency counter, my carrier is the same frequency as the frequency display. However, in

Note: My 30MHz reference had drifted so much over the years (courtesy of the attached heater I'm sure) that I couldn't pull it into range with the existing trimmer. I ended up changing the trimmer and

This gets better. I pulled the rig out of line, put it on my bench (in a cooler environment) and the next day I had a go at adjusting the 30MHz reference and VCO trimmers. Exactly, perfectly on

Mat, ? I replaced the trimmer with a nice ceramic one that Paul W6XA found in my first 980.? Problems with the trimmer and the vcv is well documented in the 1983 and 1984 Fox Tango newsletter.? I

I purchased an assortment of NOS Russian trimmer caps at Dayton.? A good quality ceramic trimmer *should* be NP0 :) I was lucky, and I found one that dropped in any worked perfectly. The range was

Anyone know where to source these parts in both the correct capacitance range and temperature coefficient? Over Christmas break I repaired several PLL/VCO Units whose OEM trimmers had become

I fixed the problem of not resetting the receiver by switching the? center wire to the tx terminal from the rx terminal. (on the FRB-1).? ? The story about the FRB-1 relay box is that Carlos

Have you tried multiple FRB-1s and determined if the problem persists across them? I think I have 4 or 5 of the things around here, in addition to a couple of control cables for Dunestar bandpass

Mat, ? I found the FIF-232 for the FT-980 lacking.? I sold my copy to a ham with a FT-1000MP where it worked as advertised.? Tjhe first FIF was for apple in the 1980's. Dave K4JRB

Shipped to James! I am glad it will go to someone with an FT-980 ... and James might help us with the Hamlib and CAT efforts! -- -Mat Breton, N8TW

Mat, ? Cutting the receiver off happens so far on SSB and have no tried CW or RTTY.? AM set up for CW will tyry that today.? I did not make any changes to the ground system and both the amp and 980

Three! Very lucky ... I've never even seen one at a hamfest. I had a similar problem, but the problem was an RF ground that I made worse when my new and neater cabling apparently lowered the ground

Gang, ? I use the FRB-1 relay box to key my amp.? I recently redid the cable to the amp at the FRB-1.? It keys the amp but for some reason?I transmit once and the amp does not fully bring the

Hi James, I sent an email to you ... -- -Mat Breton, N8TW