开云体育

Hi Phil, Inrad sells a 6th-order 47.055MHz crystal roofing filter meant for the FT-980, but I don't know anyone who has installed it (and certainly no one who has done pre/post testing to see effects

Thanks Fred. That description makes sense. I've ordered a connector for the ACC1 facility and will link the appropriate pins etc. The relevant pins are indeed described within the RSGB RadCom

I created a Dropbox folder for "work in progress" type material, and uploaded my current hamlib alpha-testing directory. Let me know if you don't receive and email invitation ... fldigi has a number

Phil, It's been a while since I had my FTV-901R/FT-980 connected together, but I did a test with one of my '980s last night (w/o transverter). The V/U button doesn't have an effect, and the Operating

I'd love to see this fully completed and can help debug, develop, what have you. See my comments in the WSJT-X thread regarding flrig - that's another package in need of update. 73 - Fred, N8YX

Ubuntu or Red Hat are what I've used the most - various flavors thereof - though you can install anything you want as long as you can get to the repos for the tools and support libraries. Most mirrors

This is how I set it up as well (except I'm using a W64 system).? I think I've figured out how hamlib works, next step it to set up a toolchain. I may have to set up a linux machine since it will be

I've gone through "Alpha" testing of the opensource hamlib interface library code (v4.0). The ft-980 code (ft-980.c) is listed at "Alpha", or untested. The Alpha code only has 6 functions listed:

Well, that just proves that you never stop learning! I had no idea that the keypad could be used for doing that. I'll give that a try when I get back to the shack. Does it only do it if the links ae

I now have the FT-980 functioning in WSJT-X, which is running on Mint Tricia 19.3 (see above). My PTT setup in WSJT-X is VOX and this is handled through a SignaLink USB interface. Once I set audio and

What are you doing with setup parms in WSJT-X for the FIF-232/'980, Mat? I have 5 serial ports on this particular system - /ttys0 and /ttys4-7. I -think- my CAT connection is currently on /ttys0 but

Phil, You were right on about the RSGB RadCom review. I just uploaded the article to our Files Folder 08. 73 Roger VE7LB

Phil, You can do this from the front panel by selecting the "Key -> V/U" buttons. I have an FTV-901R that's been modified by Yaesu to work with the '980 and IIRC it toggles those lines as its band

Hi All. I'm new here, so be kind.......? ? 8-) I've got two 980s - one of them was my first solid state rig, bought new in the mid-80s and the other is a donor rig I got hold of for a song some 20

Your logic makes sense: if the blocking diode was defective-shorted (vs open), it could expose the MCU pin to raw IO voltage (vs emulating a low-side driver). If the FC-757 is like the 980, Yaesu

Did some digging into the tuner this morning. First order of business was to verify correct voltage on each of the four Band Data lines as the various bands were selected by the '980. This checked

The next time someone takes off the IF PCB, could you snap a high-res picture for me? I'm trying to check to see if a jumper on the back was put back on the correct pads ... doesn't seem to match the

My rig actually came with the MH-1B8 hand mic (the FT-980 standard 600 ohm hand mic) ... I quickly retired it somewhere. I'll try to dig it up. I would not be shocked if the mic element was not in as

Mark, Do you have another mic to try with your rig? I get more than adequate drive with an MD1- series desk mic and don't have to open up the Mic Gain very far to obtain an ALC reading. 73 - Fred,

Anyone else in the group using this combo? I dragged my tuner and FIF-232 out of storage today and along with one of my '980s, set it up for FT8. That rig and tuner ensemble work MUCH better than