Re: ft60r radio

F5VMR

Yes I had the same problem, but realised the repeater shift was in the wrong
direction ie. out of band.


Chris F5VMR

Re: ft60r radio

#17674

You could be trying to transmit on a frequency outside the pre programmed limits. I get a 'error' message in this case.

Best Regards
Barry MacColl

On 02 Mar 2016 14:49, "Barry Fitch ab9xp@... [FT-60]" <FT-60@...> wrote:

Show quoted text

?

I am having a problem with my ft-60r radio, when I press the ptt button on the radio the screen goes blank and then it say's error.? Any help with this matter would be greatly appreciated.? This my first post, I just joined the group tonight.? Thanks for any help given.

Re: ft60r radio

Jim K5JG

#17669

Barry,

Sounds like the transmit frequency is out of band. You probably need double-check your programming, specifically the transmit offset.

73, Jim K5JG

Show quoted text

On 3/1/2016 10:03 PM, Barry Fitch ab9xp@... [FT-60] wrote:


I am having a problem with my ft-60r radio, when I press the ptt button
on the radio the screen goes blank and then it say's error.  Any help
with this matter would be greatly appreciated.  This my first post, I
just joined the group tonight.  Thanks for any help given.

Re: ft60r radio

#17668

开云体育

If you don't have it on a charger, it is the battery. ?If you have on a charger or wall wart, the wall wart does not have enough umph to power the radio while transmitting. ?If you have the radio plugged in to a car outlet, there should be enough to operate on. ?You need at least around 3 amps, wall wart only puts out around 500 mah. ?

Jardy Dawson

WA7JRD Ham Radio

Message relayed through SETI (Search for Extra-Terrestrial Intelligence, although no terrestrial intelligence has been found yet, either)

Show quoted text

On Mar 1, 2016, at 20:03, Barry Fitch ab9xp@... [FT-60] <FT-60@...> wrote:

I am having a problem with my ft-60r radio, when I press the ptt button on the radio the screen goes blank and then it say's error.? Any help with this matter would be greatly appreciated.? This my first post, I just joined the group tonight.? Thanks for any help given.

Re: ft60r radio

Ron Samson

#17671

If you attempt to transmit "out of band" you will get this response

Sent from

On Wed, Mar 2, 2016 at 5:02 AM -0800, "Jack Travis ae8p@... [FT-60]" <FT-60@...> wrote:

Show quoted text

?

Sounds like you have a bad battery. It may test at 8.0+ V but under load the voltage drops below usable. That’s typical response.

Jack, ae8p

On Mar 1, 2016, at 11:03 PM, Barry Fitch ab9xp@... [FT-60] wrote:

I am having a problem with my ft-60r radio, when I press the ptt button on the radio the screen goes blank and then it say's error. Any help with this matter would be greatly appreciated. This my first post, I just joined the group tonight. Thanks for any help given.

Re: ft60r radio

#17667

Sounds like you have a bad battery.  It may test at 8.0+ V but under load the voltage drops below usable.  That’s typical response.

Jack, ae8p

Show quoted text

On Mar 1, 2016, at 11:03 PM, Barry Fitch ab9xp@... [FT-60] <FT-60@...> wrote:

I am having a problem with my ft-60r radio, when I press the ptt button on the radio the screen goes blank and then it say's error.  Any help with this matter would be greatly appreciated.  This my first post, I just joined the group tonight.  Thanks for any help given.

Re: ft60r radio

#17673

开云体育

You may want to verify your battery is fully charged.

?

Rick

?

Show quoted text

From: FT-60@... [mailto:FT-60@...]
Sent: Tuesday, March 01, 2016 9:03 PM
To: FT-60@...
Subject: [FT-60] ft60r radio

?

I am having a problem with my ft-60r radio, when I press the ptt button on the radio the screen goes blank and then it say's error.? Any help with this matter would be greatly appreciated.? This my first post, I just joined the group tonight.? Thanks for any help given.

Re: ft60r radio

#17670

Barry, you may have the radio set to receive on the frequency you see on the face of it, but you are transmitting on a different frequency that is out of band.? Give that a look-see.

73 Dave W0DLR

?

ft60r radio

#17666

I am having a problem with my ft-60r radio, when I press the ptt button on the radio the screen goes blank and then it say's error.? Any help with this matter would be greatly appreciated.? This my first post, I just joined the group tonight.? Thanks for any help given.

Re: Programming using Chirp

#17665

Hi All,
thanks for the responses. I've had success now and I have successfully loaded up several memories to the FT60. I'm not quite sure what I did, but after trying several times it eventually worked. Chirp seems a good and simple package to use, but if there are continuing issues i'll try the FT60 Commander software, that sounds like a useful alternative.

Cheers and thanks again

Dave
M0IKT

Re: Programming using Chirp

#17664

开云体育

Since I got my FT-60, I've been using FT-60 Commander software. ?It's a free program and can be found at?? Even if you get the other software working, back-ups are a good thing.

Good luck!

+++++

Jerry

KG7NOR

+++++

Scientific knowledge is a body of statements of varying degrees of certainty--some mostly unsure, some nearly sure, but none absolutely certain.

Richard Feynman, Nobel Prize winning ?physicist

From: FT-60@...
To: FT-60@...
Date: Wed, 17 Feb 2016 06:47:43 -0800
Subject: Re: [FT-60] Programming using Chirp

I've also had some issues w/ same. ?Here's what worked for me, on Vista & Win8:?

Use?3.2.0.0 Prolific Driver.

UPLOADING TO RADIO

1. attach cable

2. put radio into CLONE: TX mode

3. press PTT

4. radio shows ERROR

5. hit MONI button

6. radio shows "RX"

7. start "Upload to radio"

8. upload should run

DOWNLOADING FROM RADIO

1. attach cable

2. put radio into CLONE mode

3. start "Download from radio"

4. press PTT

5. download should run

ALTERNATE UPLOADING TO RADIO

1. attach cable

2. [start "Download from radio"]

3. put radio into CLONE: TX mode

4. [download should run]

5. press PTT

6. radio shows ERROR

7. hit MONI button

8. radio shows "RX"

9. start "Upload to radio"

10. upload should run

Good luck!

Aldo

W2AGC

?

Re: FT-60 noise

Goldwing66

#17663

i fixed it by adjusting the squelch. thanks.

Show quoted text

-----Original Message-----
From: Jardy JARDY72@... [FT-60]
To: FT-60
Sent: Tue, Feb 16, 2016 9:55 pm
Subject: Re: [FT-60] FT-60 noise

Does it happen everywhere, or just in one particular location?

Jardy Dawson WA7JRD

Nobody really cares what device you are using, as long as YOU like it!

On Feb 16, 2016, at 15:16, Goldwing66 goldwing66@... [FT-60] <FT-60@...> wrote:

?

No

Sent from AOL Mobile Mail

-----Original Message-----
From: Jardy JARDY72@... [FT-60] <FT-60@...>
To: FT-60 <FT-60@...>
Sent: Tue, Feb 16, 2016 04:14 PM
Subject: Re: [FT-60] FT-60 noise

?

Do you have a battery saver turned on? ? Dual watch or priority?

Jardy Dawson WA7JRD
Nobody really cares what device you are using, as long as YOU like it!

On Feb 16, 2016, at 08:07, goldwing66@... [FT-60] <FT-60@...> wrote:

?

My FT-60 has started making a short one second squelch like noise every minute or so. Any ideas what might be causing it?

Re: Programming using Chirp

[email protected]

#17662

I've also had some issues w/ same. ?Here's what worked for me, on Vista & Win8:?

Use?3.2.0.0 Prolific Driver.

UPLOADING TO RADIO

1. attach cable

2. put radio into CLONE: TX mode

3. press PTT

4. radio shows ERROR

5. hit MONI button

6. radio shows "RX"

7. start "Upload to radio"

8. upload should run

DOWNLOADING FROM RADIO

1. attach cable

2. put radio into CLONE mode

3. start "Download from radio"

4. press PTT

5. download should run

ALTERNATE UPLOADING TO RADIO

1. attach cable

2. [start "Download from radio"]

3. put radio into CLONE: TX mode

4. [download should run]

5. press PTT

6. radio shows ERROR

7. hit MONI button

8. radio shows "RX"

9. start "Upload to radio"

10. upload should run

Good luck!

Aldo

W2AGC

?

Re: Programming using Chirp

#17661

Or switch to RT Systems software and cables. ? No problems .?

?

Dave J?

Show quoted text

From: "Steve - W3SLL w3sll@... [FT-60]"
To: FT-60@...
Sent: Tuesday, February 16, 2016 6:15 PM
Subject: Re: [FT-60] Programming using Chirp

?

Try a different version of chirp. One back or the next daily build. I have seen this before and the last time it happened to me, I stepped back 1 version.
--------------------------------------------
On Tue, 2/16/16, cappers1001@... [FT-60] wrote:

Subject: [FT-60] Programming using Chirp
To: FT-60@...
Date: Tuesday, February 16, 2016, 5:38 PM

?

Hi All,
I've just started using
Chirp to program my ft60. Unfortunately i'm having a
problem uploading my file to the tx.
I seem
to download from the ft60 no problem and am able to edit the
resultant .img file, but when I come to upload it again
after my edits I have an error message that says 'failed
to communicate with radio. Radio did not respond'. The
COM port seems correct, the vendor and model number, while
greyed out are correct. Any ideas what's going on?

Dave
M0IKT

#yiv3274891366 #yiv3274891366 --
#yiv3274891366ygrp-mkp {
border:1px solid #d8d8d8;font-family:Arial;margin:10px
0;padding:0 10px;}

#yiv3274891366 #yiv3274891366ygrp-mkp hr {
border:1px solid #d8d8d8;}

#yiv3274891366 #yiv3274891366ygrp-mkp #yiv3274891366hd {
color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px
0;}

#yiv3274891366 #yiv3274891366ygrp-mkp #yiv3274891366ads {
margin-bottom:10px;}

#yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad {
padding:0 0;}

#yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad p {
margin:0;}

#yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad a {
color:#0000ff;text-decoration:none;}
#yiv3274891366 #yiv3274891366ygrp-sponsor
#yiv3274891366ygrp-lc {
font-family:Arial;}

#yiv3274891366 #yiv3274891366ygrp-sponsor
#yiv3274891366ygrp-lc #yiv3274891366hd {
margin:10px
0px;font-weight:700;font-size:78%;line-height:122%;}

#yiv3274891366 #yiv3274891366ygrp-sponsor
#yiv3274891366ygrp-lc .yiv3274891366ad {
margin-bottom:10px;padding:0 0;}

#yiv3274891366 #yiv3274891366actions {
font-family:Verdana;font-size:11px;padding:10px 0;}

#yiv3274891366 #yiv3274891366activity {
background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;}

#yiv3274891366 #yiv3274891366activity span {
font-weight:700;}

#yiv3274891366 #yiv3274891366activity span:first-child {
text-transform:uppercase;}

#yiv3274891366 #yiv3274891366activity span a {
color:#5085b6;text-decoration:none;}

#yiv3274891366 #yiv3274891366activity span span {
color:#ff7900;}

#yiv3274891366 #yiv3274891366activity span
.yiv3274891366underline {
text-decoration:underline;}

#yiv3274891366 .yiv3274891366attach {
clear:both;display:table;font-family:Arial;font-size:12px;padding:10px
0;width:400px;}

#yiv3274891366 .yiv3274891366attach div a {
text-decoration:none;}

#yiv3274891366 .yiv3274891366attach img {
border:none;padding-right:5px;}

#yiv3274891366 .yiv3274891366attach label {
display:block;margin-bottom:5px;}

#yiv3274891366 .yiv3274891366attach label a {
text-decoration:none;}

#yiv3274891366 blockquote {
margin:0 0 0 4px;}

#yiv3274891366 .yiv3274891366bold {
font-family:Arial;font-size:13px;font-weight:700;}

#yiv3274891366 .yiv3274891366bold a {
text-decoration:none;}

#yiv3274891366 dd.yiv3274891366last p a {
font-family:Verdana;font-weight:700;}

#yiv3274891366 dd.yiv3274891366last p span {
margin-right:10px;font-family:Verdana;font-weight:700;}

#yiv3274891366 dd.yiv3274891366last p
span.yiv3274891366yshortcuts {
margin-right:0;}

#yiv3274891366 div.yiv3274891366attach-table div div a {
text-decoration:none;}

#yiv3274891366 div.yiv3274891366attach-table {
width:400px;}

#yiv3274891366 div.yiv3274891366file-title a, #yiv3274891366
div.yiv3274891366file-title a:active, #yiv3274891366
div.yiv3274891366file-title a:hover, #yiv3274891366
div.yiv3274891366file-title a:visited {
text-decoration:none;}

#yiv3274891366 div.yiv3274891366photo-title a,
#yiv3274891366 div.yiv3274891366photo-title a:active,
#yiv3274891366 div.yiv3274891366photo-title a:hover,
#yiv3274891366 div.yiv3274891366photo-title a:visited {
text-decoration:none;}

#yiv3274891366 div#yiv3274891366ygrp-mlmsg
#yiv3274891366ygrp-msg p a span.yiv3274891366yshortcuts {
font-family:Verdana;font-size:10px;font-weight:normal;}

#yiv3274891366 .yiv3274891366green {
color:#628c2a;}

#yiv3274891366 .yiv3274891366MsoNormal {
margin:0 0 0 0;}

#yiv3274891366 o {
font-size:0;}

#yiv3274891366 #yiv3274891366photos div {
float:left;width:72px;}

#yiv3274891366 #yiv3274891366photos div div {
border:1px solid
#666666;height:62px;overflow:hidden;width:62px;}

#yiv3274891366 #yiv3274891366photos div label {
color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;}

#yiv3274891366 #yiv3274891366reco-category {
font-size:77%;}

#yiv3274891366 #yiv3274891366reco-desc {
font-size:77%;}

#yiv3274891366 .yiv3274891366replbq {
margin:4px;}

#yiv3274891366 #yiv3274891366ygrp-actbar div a:first-child {
margin-right:2px;padding-right:5px;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg {
font-size:13px;font-family:Arial, helvetica, clean,
sans-serif;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg table {
font-size:inherit;font:100%;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg select,
#yiv3274891366 input, #yiv3274891366 textarea {
font:99% Arial, Helvetica, clean, sans-serif;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg pre, #yiv3274891366
code {
font:115% monospace;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg * {
line-height:1.22em;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg #yiv3274891366logo {
padding-bottom:10px;}

#yiv3274891366 #yiv3274891366ygrp-msg p a {
font-family:Verdana;}

#yiv3274891366 #yiv3274891366ygrp-msg
p#yiv3274891366attach-count span {
color:#1E66AE;font-weight:700;}

#yiv3274891366 #yiv3274891366ygrp-reco
#yiv3274891366reco-head {
color:#ff7900;font-weight:700;}

#yiv3274891366 #yiv3274891366ygrp-reco {
margin-bottom:20px;padding:0px;}

#yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
li a {
font-size:130%;text-decoration:none;}

#yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
li {
font-size:77%;list-style-type:square;padding:6px 0;}

#yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
ul {
margin:0;padding:0 0 0 8px;}

#yiv3274891366 #yiv3274891366ygrp-text {
font-family:Georgia;}

#yiv3274891366 #yiv3274891366ygrp-text p {
margin:0 0 1em 0;}

#yiv3274891366 #yiv3274891366ygrp-text tt {
font-size:120%;}

#yiv3274891366 #yiv3274891366ygrp-vital ul li:last-child {
border-right:none !important;
}
#yiv3274891366

Re: FT-60 noise

#17660

开云体育

Does it happen everywhere, or just in one particular location?

Jardy Dawson WA7JRD

Nobody really cares what device you are using, as long as YOU like it!

Show quoted text

On Feb 16, 2016, at 15:16, Goldwing66 goldwing66@... [FT-60] <FT-60@...> wrote:

?

No

Sent from AOL Mobile Mail

-----Original Message-----
From: Jardy JARDY72@... [FT-60] <FT-60@...>
To: FT-60 <FT-60@...>
Sent: Tue, Feb 16, 2016 04:14 PM
Subject: Re: [FT-60] FT-60 noise

?

Do you have a battery saver turned on? ? Dual watch or priority?

Jardy Dawson WA7JRD
Nobody really cares what device you are using, as long as YOU like it!

On Feb 16, 2016, at 08:07, goldwing66@... [FT-60] <FT-60@...> wrote:

?

My FT-60 has started making a short one second squelch like noise every minute or so. Any ideas what might be causing it?

Re: Programming using Chirp

#17659

开云体育

If you have the fake Prolific chip in your cable, make sure you are using the 3.2.0.0 driver. You could also try using. The FT-60 Commander software at . Use the alternate write method. Also make sure cable is all the way into the radio.?

Jardy Dawson WA7JRD

Nobody really cares what device you are using, as long as YOU like it!

Show quoted text

On Feb 16, 2016, at 17:15, Steve - W3SLL w3sll@... [FT-60] <FT-60@...> wrote:

?

Try a different version of chirp. One back or the next daily build. I have seen this before and the last time it happened to me, I stepped back 1 version.
--------------------------------------------
On Tue, 2/16/16, cappers1001@... [FT-60] <FT-60@...> wrote:

Subject: [FT-60] Programming using Chirp
To: FT-60@...
Date: Tuesday, February 16, 2016, 5:38 PM

?

Hi All,
I've just started using
Chirp to program my ft60. Unfortunately i'm having a
problem uploading my file to the tx.
I seem
to download from the ft60 no problem and am able to edit the
resultant .img file, but when I come to upload it again
after my edits I have an error message that says 'failed
to communicate with radio. Radio did not respond'. The
COM port seems correct, the vendor and model number, while
greyed out are correct. Any ideas what's going on?

Dave
M0IKT

#yiv3274891366 #yiv3274891366 --
#yiv3274891366ygrp-mkp {
border:1px solid #d8d8d8;font-family:Arial;margin:10px
0;padding:0 10px;}

#yiv3274891366 #yiv3274891366ygrp-mkp hr {
border:1px solid #d8d8d8;}

#yiv3274891366 #yiv3274891366ygrp-mkp #yiv3274891366hd {
color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px
0;}

#yiv3274891366 #yiv3274891366ygrp-mkp #yiv3274891366ads {
margin-bottom:10px;}

#yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad {
padding:0 0;}

#yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad p {
margin:0;}

#yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad a {
color:#0000ff;text-decoration:none;}
#yiv3274891366 #yiv3274891366ygrp-sponsor
#yiv3274891366ygrp-lc {
font-family:Arial;}

#yiv3274891366 #yiv3274891366ygrp-sponsor
#yiv3274891366ygrp-lc #yiv3274891366hd {
margin:10px
0px;font-weight:700;font-size:78%;line-height:122%;}

#yiv3274891366 #yiv3274891366ygrp-sponsor
#yiv3274891366ygrp-lc .yiv3274891366ad {
margin-bottom:10px;padding:0 0;}

#yiv3274891366 #yiv3274891366actions {
font-family:Verdana;font-size:11px;padding:10px 0;}

#yiv3274891366 #yiv3274891366activity {
background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;}

#yiv3274891366 #yiv3274891366activity span {
font-weight:700;}

#yiv3274891366 #yiv3274891366activity span:first-child {
text-transform:uppercase;}

#yiv3274891366 #yiv3274891366activity span a {
color:#5085b6;text-decoration:none;}

#yiv3274891366 #yiv3274891366activity span span {
color:#ff7900;}

#yiv3274891366 #yiv3274891366activity span
.yiv3274891366underline {
text-decoration:underline;}

#yiv3274891366 .yiv3274891366attach {
clear:both;display:table;font-family:Arial;font-size:12px;padding:10px
0;width:400px;}

#yiv3274891366 .yiv3274891366attach div a {
text-decoration:none;}

#yiv3274891366 .yiv3274891366attach img {
border:none;padding-right:5px;}

#yiv3274891366 .yiv3274891366attach label {
display:block;margin-bottom:5px;}

#yiv3274891366 .yiv3274891366attach label a {
text-decoration:none;}

#yiv3274891366 blockquote {
margin:0 0 0 4px;}

#yiv3274891366 .yiv3274891366bold {
font-family:Arial;font-size:13px;font-weight:700;}

#yiv3274891366 .yiv3274891366bold a {
text-decoration:none;}

#yiv3274891366 dd.yiv3274891366last p a {
font-family:Verdana;font-weight:700;}

#yiv3274891366 dd.yiv3274891366last p span {
margin-right:10px;font-family:Verdana;font-weight:700;}

#yiv3274891366 dd.yiv3274891366last p
span.yiv3274891366yshortcuts {
margin-right:0;}

#yiv3274891366 div.yiv3274891366attach-table div div a {
text-decoration:none;}

#yiv3274891366 div.yiv3274891366attach-table {
width:400px;}

#yiv3274891366 div.yiv3274891366file-title a, #yiv3274891366
div.yiv3274891366file-title a:active, #yiv3274891366
div.yiv3274891366file-title a:hover, #yiv3274891366
div.yiv3274891366file-title a:visited {
text-decoration:none;}

#yiv3274891366 div.yiv3274891366photo-title a,
#yiv3274891366 div.yiv3274891366photo-title a:active,
#yiv3274891366 div.yiv3274891366photo-title a:hover,
#yiv3274891366 div.yiv3274891366photo-title a:visited {
text-decoration:none;}

#yiv3274891366 div#yiv3274891366ygrp-mlmsg
#yiv3274891366ygrp-msg p a span.yiv3274891366yshortcuts {
font-family:Verdana;font-size:10px;font-weight:normal;}

#yiv3274891366 .yiv3274891366green {
color:#628c2a;}

#yiv3274891366 .yiv3274891366MsoNormal {
margin:0 0 0 0;}

#yiv3274891366 o {
font-size:0;}

#yiv3274891366 #yiv3274891366photos div {
float:left;width:72px;}

#yiv3274891366 #yiv3274891366photos div div {
border:1px solid
#666666;height:62px;overflow:hidden;width:62px;}

#yiv3274891366 #yiv3274891366photos div label {
color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;}

#yiv3274891366 #yiv3274891366reco-category {
font-size:77%;}

#yiv3274891366 #yiv3274891366reco-desc {
font-size:77%;}

#yiv3274891366 .yiv3274891366replbq {
margin:4px;}

#yiv3274891366 #yiv3274891366ygrp-actbar div a:first-child {
margin-right:2px;padding-right:5px;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg {
font-size:13px;font-family:Arial, helvetica, clean,
sans-serif;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg table {
font-size:inherit;font:100%;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg select,
#yiv3274891366 input, #yiv3274891366 textarea {
font:99% Arial, Helvetica, clean, sans-serif;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg pre, #yiv3274891366
code {
font:115% monospace;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg * {
line-height:1.22em;}

#yiv3274891366 #yiv3274891366ygrp-mlmsg #yiv3274891366logo {
padding-bottom:10px;}

#yiv3274891366 #yiv3274891366ygrp-msg p a {
font-family:Verdana;}

#yiv3274891366 #yiv3274891366ygrp-msg
p#yiv3274891366attach-count span {
color:#1E66AE;font-weight:700;}

#yiv3274891366 #yiv3274891366ygrp-reco
#yiv3274891366reco-head {
color:#ff7900;font-weight:700;}

#yiv3274891366 #yiv3274891366ygrp-reco {
margin-bottom:20px;padding:0px;}

#yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
li a {
font-size:130%;text-decoration:none;}

#yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
li {
font-size:77%;list-style-type:square;padding:6px 0;}

#yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
ul {
margin:0;padding:0 0 0 8px;}

#yiv3274891366 #yiv3274891366ygrp-text {
font-family:Georgia;}

#yiv3274891366 #yiv3274891366ygrp-text p {
margin:0 0 1em 0;}

#yiv3274891366 #yiv3274891366ygrp-text tt {
font-size:120%;}

#yiv3274891366 #yiv3274891366ygrp-vital ul li:last-child {
border-right:none !important;
}
#yiv3274891366

Re: Programming using Chirp

Steve - W3SLL

#17658

Try a different version of chirp. One back or the next daily build. I have seen this before and the last time it happened to me, I stepped back 1 version.
--------------------------------------------

Show quoted text

On Tue, 2/16/16, cappers1001@... [FT-60] <FT-60@...> wrote:

 Subject: [FT-60] Programming using Chirp
 To: FT-60@...
 Date: Tuesday, February 16, 2016, 5:38 PM


 ?









       Hi All,
 I've just started using
 Chirp to program my ft60. Unfortunately i'm having a
 problem uploading my file to the tx.
 I seem
 to download from the ft60 no problem and am able to edit the
 resultant .img file, but when I come to upload it again
 after my edits I have an error message that says 'failed
 to communicate with radio. Radio did not respond'. The
 COM port seems correct, the vendor and model number, while
 greyed out are correct. Any ideas what's going on?

 Dave
 M0IKT








 
 #yiv3274891366 #yiv3274891366 --
   #yiv3274891366ygrp-mkp {
 border:1px solid #d8d8d8;font-family:Arial;margin:10px
 0;padding:0 10px;}

 #yiv3274891366 #yiv3274891366ygrp-mkp hr {
 border:1px solid #d8d8d8;}

 #yiv3274891366 #yiv3274891366ygrp-mkp #yiv3274891366hd {
 color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px
 0;}

 #yiv3274891366 #yiv3274891366ygrp-mkp #yiv3274891366ads {
 margin-bottom:10px;}

 #yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad {
 padding:0 0;}

 #yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad p {
 margin:0;}

 #yiv3274891366 #yiv3274891366ygrp-mkp .yiv3274891366ad a {
 color:#0000ff;text-decoration:none;}
 #yiv3274891366 #yiv3274891366ygrp-sponsor
 #yiv3274891366ygrp-lc {
 font-family:Arial;}

 #yiv3274891366 #yiv3274891366ygrp-sponsor
 #yiv3274891366ygrp-lc #yiv3274891366hd {
 margin:10px
 0px;font-weight:700;font-size:78%;line-height:122%;}

 #yiv3274891366 #yiv3274891366ygrp-sponsor
 #yiv3274891366ygrp-lc .yiv3274891366ad {
 margin-bottom:10px;padding:0 0;}

 #yiv3274891366 #yiv3274891366actions {
 font-family:Verdana;font-size:11px;padding:10px 0;}

 #yiv3274891366 #yiv3274891366activity {
 background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;}

 #yiv3274891366 #yiv3274891366activity span {
 font-weight:700;}

 #yiv3274891366 #yiv3274891366activity span:first-child {
 text-transform:uppercase;}

 #yiv3274891366 #yiv3274891366activity span a {
 color:#5085b6;text-decoration:none;}

 #yiv3274891366 #yiv3274891366activity span span {
 color:#ff7900;}

 #yiv3274891366 #yiv3274891366activity span
 .yiv3274891366underline {
 text-decoration:underline;}

 #yiv3274891366 .yiv3274891366attach {
 clear:both;display:table;font-family:Arial;font-size:12px;padding:10px
 0;width:400px;}

 #yiv3274891366 .yiv3274891366attach div a {
 text-decoration:none;}

 #yiv3274891366 .yiv3274891366attach img {
 border:none;padding-right:5px;}

 #yiv3274891366 .yiv3274891366attach label {
 display:block;margin-bottom:5px;}

 #yiv3274891366 .yiv3274891366attach label a {
 text-decoration:none;}

 #yiv3274891366 blockquote {
 margin:0 0 0 4px;}

 #yiv3274891366 .yiv3274891366bold {
 font-family:Arial;font-size:13px;font-weight:700;}

 #yiv3274891366 .yiv3274891366bold a {
 text-decoration:none;}

 #yiv3274891366 dd.yiv3274891366last p a {
 font-family:Verdana;font-weight:700;}

 #yiv3274891366 dd.yiv3274891366last p span {
 margin-right:10px;font-family:Verdana;font-weight:700;}

 #yiv3274891366 dd.yiv3274891366last p
 span.yiv3274891366yshortcuts {
 margin-right:0;}

 #yiv3274891366 div.yiv3274891366attach-table div div a {
 text-decoration:none;}

 #yiv3274891366 div.yiv3274891366attach-table {
 width:400px;}

 #yiv3274891366 div.yiv3274891366file-title a, #yiv3274891366
 div.yiv3274891366file-title a:active, #yiv3274891366
 div.yiv3274891366file-title a:hover, #yiv3274891366
 div.yiv3274891366file-title a:visited {
 text-decoration:none;}

 #yiv3274891366 div.yiv3274891366photo-title a,
 #yiv3274891366 div.yiv3274891366photo-title a:active,
 #yiv3274891366 div.yiv3274891366photo-title a:hover,
 #yiv3274891366 div.yiv3274891366photo-title a:visited {
 text-decoration:none;}

 #yiv3274891366 div#yiv3274891366ygrp-mlmsg
 #yiv3274891366ygrp-msg p a span.yiv3274891366yshortcuts {
 font-family:Verdana;font-size:10px;font-weight:normal;}

 #yiv3274891366 .yiv3274891366green {
 color:#628c2a;}

 #yiv3274891366 .yiv3274891366MsoNormal {
 margin:0 0 0 0;}

 #yiv3274891366 o {
 font-size:0;}

 #yiv3274891366 #yiv3274891366photos div {
 float:left;width:72px;}

 #yiv3274891366 #yiv3274891366photos div div {
 border:1px solid
 #666666;height:62px;overflow:hidden;width:62px;}

 #yiv3274891366 #yiv3274891366photos div label {
 color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;}

 #yiv3274891366 #yiv3274891366reco-category {
 font-size:77%;}

 #yiv3274891366 #yiv3274891366reco-desc {
 font-size:77%;}

 #yiv3274891366 .yiv3274891366replbq {
 margin:4px;}

 #yiv3274891366 #yiv3274891366ygrp-actbar div a:first-child {
 margin-right:2px;padding-right:5px;}

 #yiv3274891366 #yiv3274891366ygrp-mlmsg {
 font-size:13px;font-family:Arial, helvetica, clean,
 sans-serif;}

 #yiv3274891366 #yiv3274891366ygrp-mlmsg table {
 font-size:inherit;font:100%;}

 #yiv3274891366 #yiv3274891366ygrp-mlmsg select,
 #yiv3274891366 input, #yiv3274891366 textarea {
 font:99% Arial, Helvetica, clean, sans-serif;}

 #yiv3274891366 #yiv3274891366ygrp-mlmsg pre, #yiv3274891366
 code {
 font:115% monospace;}

 #yiv3274891366 #yiv3274891366ygrp-mlmsg * {
 line-height:1.22em;}

 #yiv3274891366 #yiv3274891366ygrp-mlmsg #yiv3274891366logo {
 padding-bottom:10px;}


 #yiv3274891366 #yiv3274891366ygrp-msg p a {
 font-family:Verdana;}

 #yiv3274891366 #yiv3274891366ygrp-msg
 p#yiv3274891366attach-count span {
 color:#1E66AE;font-weight:700;}

 #yiv3274891366 #yiv3274891366ygrp-reco
 #yiv3274891366reco-head {
 color:#ff7900;font-weight:700;}

 #yiv3274891366 #yiv3274891366ygrp-reco {
 margin-bottom:20px;padding:0px;}

 #yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
 li a {
 font-size:130%;text-decoration:none;}

 #yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
 li {
 font-size:77%;list-style-type:square;padding:6px 0;}

 #yiv3274891366 #yiv3274891366ygrp-sponsor #yiv3274891366ov
 ul {
 margin:0;padding:0 0 0 8px;}

 #yiv3274891366 #yiv3274891366ygrp-text {
 font-family:Georgia;}

 #yiv3274891366 #yiv3274891366ygrp-text p {
 margin:0 0 1em 0;}

 #yiv3274891366 #yiv3274891366ygrp-text tt {
 font-size:120%;}

 #yiv3274891366 #yiv3274891366ygrp-vital ul li:last-child {
 border-right:none !important;
 }
 #yiv3274891366

Re: FT-60 noise

Goldwing66

#17657

No

Sent from AOL Mobile Mail

Show quoted text

-----Original Message-----
From: Jardy JARDY72@... [FT-60]
To: FT-60
Sent: Tue, Feb 16, 2016 04:14 PM
Subject: Re: [FT-60] FT-60 noise

Do you have a battery saver turned on? ? Dual watch or priority?

Jardy Dawson WA7JRD

Nobody really cares what device you are using, as long as YOU like it!

On Feb 16, 2016, at 08:07, goldwing66@... [FT-60] <FT-60@...> wrote:

?

My FT-60 has started making a short one second squelch like noise every minute or so. Any ideas what might be causing it?

Re: FT-60 noise

#17655

开云体育

Do you have a battery saver turned on? ? Dual watch or priority?

Jardy Dawson WA7JRD

Nobody really cares what device you are using, as long as YOU like it!

Show quoted text

On Feb 16, 2016, at 08:07, goldwing66@... [FT-60] <FT-60@...> wrote:

?

My FT-60 has started making a short one second squelch like noise every minute or so. Any ideas what might be causing it?

Programming using Chirp

#17656

Hi All,
I've just started using Chirp to program my ft60. Unfortunately i'm having a problem uploading my file to the tx.
I seem to download from the ft60 no problem and am able to edit the resultant .img file, but when I come to upload it again after my edits I have an error message that says 'failed to communicate with radio. Radio did not respond'. The COM port seems correct, the vendor and model number, while greyed out are correct. Any ideas what's going on?

Dave
M0IKT