I'm struggling to configure a YD7403 via the config tools, I'm using the latest build of the software but when I try to change the CVs to turn the booster on/off nothing is saved after clicking the green ticket when I then reopen the page.
The logging output shows this - any ideas? Thanks in advance!
2471: YD.Q:C:TRK
0084: [YU0] C:TRK IS 0 TS 1 MC 3000 SD 250 AR 0 RD 1000
0031: [YU0] C:TRK TO 0 TP 0 FN 0 FF 0
0032: [YU0] C:TRK P1 0 P2 0 N1 0 N2 0
0048: [YU0] C:TRK RG 1 RU 1 RP 1 RF 0 FS 1
0032: [YU0] C:TRK ST 0 FT 1 SO 0 FO 1 SL 0 FL 1
0064: [YU0] C:TRK EC 1 DC 5 CM 0 EV 1 DV 5 ET 1 DT 5
0032: [YU0] C:TRK TB 1 PO 0 MT 95 WT 70 SP 250
0016: [YU0] C:TRK CI 4
0449: [CS0] M:TC 0mA TV 18.0V TT 14.3'C?
5201: [CS0] M:TC 0mA TV 18.0V TT 14.3'C?
0143: YD.Y:S 7403A0000255
0100: YD.C:TRK IS 0 TS 1 MC 3000 SD 250 AR 0 RD 1000
0100: YD.C:TRK TO 10 TP 0 FN 0 FF 0
0100: YD.C:TRK P1 0 P2 0 N1 0 N2 0
0100: YD.C:TRK RG 1 RU 1 RP 1 RF 0 FS 1
0100: YD.C:TRK ST 0 FT 1 SO 0 FO 1 SL 0 FL 1
0100: YD.C:TRK EC 1 DC 5 CM 0 EV 1 DV 5 ET 1 DT 5
0100: YD.C:TRK TB 1 PO 0 MT 95 WT 70 SP 250
0100: YD.Q:C:TRK
4240: [CS0] M:TC 0mA TV 18.0V TT 14.3'C?
2552: YD.Q:C:TRK
0088: [YU0] C:TRK IS 0 TS 1 MC 3000 SD 250 AR 0 RD 1000
0032: [YU0] C:TRK TO 0 TP 0 FN 0 FF 0
0032: [YU0] C:TRK P1 0 P2 0 N1 0 N2 0
0032: [YU0] C:TRK RG 1 RU 1 RP 1 RF 0 FS 1
0048: [YU0] C:TRK ST 0 FT 1 SO 0 FO 1 SL 0 FL 1
0048: [YU0] C:TRK EC 1 DC 5 CM 0 EV 1 DV 5 ET 1 DT 5
0048: [YU0] C:TRK TB 1 PO 0 MT 95 WT 70 SP 250
0016: [YU0] C:TRK CI 4
2304: [CS0] M:TC 0mA TV 18.0V TT 14.3'C?
5185: [CS0] M:TC 0mA TV 18.0V TT 14.3'C?
5185: [CS0] M:TC 0mA TV 18.0V TT 14.3'C?
5200: [CS0] M:TC 0mA TV 18.0V TT 14.3'C
