开云体育

Oh, and please report back with your results.? Other members may also want to try AM. -- Doug, K8RFT

Try setting it MUCH lower, as someone else has suggested above.? Increasing the setting would make it even worse! Try setting at 25, as Joel did. -- Doug, K8RFT

On Tue, Oct 26, 2021 at 11:33 Submarine Radioman <wa3mck@...> wrote: > Hi Doug, > > Thank you… I’ve tried that and no success. > > Tried modulation at 60 61 62 and 63 - did not improve

Hi Doug, Thank you… I’ve tried that and no success. Tried modulation at 60 61 62 and 63 - did not improve distortion. I can see it on my spectrum analyzer and hear it on my monitor receiver -

Downward modulation is not unusual for solid state rigs on AM. I inspected the AM envelope on my spectrum analyzer with 2 tone, and it is a mess at any setting I could come up with. A trapezoid

Dale, I think Xiegu needs to bless us with another firmware upgrade for the X5105, but my experience with them is that when they get a radio almost free of bugs they quit releasing updates. Never

Hi Dale, I just conducted a test transmitting with my X5105 on 10 meter AM and found it was really distorted at the the default AM modulation level of 60, but when turned down to 45 it sounded quite

I have tried all of the settings for TX AM, and nothing makes it better. One would think that the AM mod and demod would all be done in SDR code. Simply multiplying Cos(Wm)t by Cos (Wc)t yields

Well, I have not tried AM, but the 'logical' reason would be overmodulation. Check the manual (and adjust modulation level)- System parameter configuration Personalized settings can be achieved for

Has anyone operated their x5105 on AM? Receive is fine, but Transmit is horribly distorted… please let me know. Tnx Howie wa3mck "Quis custodiet ipsos custodes?"

Mine also charges to 'about' 12.6. I've never seen any info about the serial numbers.? I'd suggest asking the dealers, like Radioddity (where I got mine) or the newer dealer, Connect Systems.? It

Thanks Karl, I guess mine is about normal then, it just seemed that is was a bit low for a fully charged LIPo battery. Joel N6ALT

Hi, ? My X5105 goes to 12.6V and no more, from new.? Not sure about the serial number question. ? Karl

The radio is pretty much as new. I am just? not using it, preferring my monoband CW rigs for portable/hiking. Comes with manual, original mic and data cable. $465 plus shipping from NC. Tnx, Dale

My internal battery charges up to 12.3V then says it's full. Is this about what others notice also? Another question, how can I tell when my X5105 was manufactured from the serial number? Joel N6ALT

That will help.? We can only know about what you actually write in your posts. Now, what program were you using when you got the error - WSJT, or something else? Is that the only error you've

Hi Doug, I finally had time to take a look at things. I have WSJT-T loaded and running. I have the radio hooked up to my digirig mobile interface and configured. I have the Icom-IC7100 selected in the

In addition, the old post #92 in this group has a schematic that was reported to be for the mic input circuit, but that's not guaranteed to be correct.? The diagram shows "PC board connections" type

I received this email earlier this week. Hope this email finds you well! Thanks again for your patience with the?Xiegu X6100?HF Transceiver, and finally,?IT'S ALMOST HERE!! Mark your calendars as

I have read somewhere about an encoder change, but on a different radio.? Try checking the Xiegu G90 group - maybe it was there.? Or at least maybe someone there has done it. -- Doug, K8RFT