开云体育

Thanks Joe for confirming what I described below!

Yes, this is what I did as well. I placed a schematic drawing of the cable I constructed in the group’s file section here: /g/X5105-Users/files/X5105%20ACC%20TRRS%20Cable.pdf

Yes, this is what I did as well. I placed a schematic drawing of the cable I constructed in the group’s file section here: /g/X5105-Users/files/X5105%20ACC%20TRRS%20Cable.pdf

Hi, some additional information here. It is absolutely not necessary to use the CE-19, you can connect the soundcard directly to the ACC connector. The AF_OUT is connected to the Mic input of the

Thanks ..I will try that setting. 73 Rob VE3 LUA

Hi, The settings I use for FT4 and other digital modes are: AGC: Slow Comp: off NR: off Notch: off L IN/OUT: on/on? G-LIN: 6? G-LOUT: 55? (Of course, it does depend on the soudcard settings) the

Rob, I do not have the XPA125 so I am answering from what I have read and seen on YouTube videos. The Smoking Ape did a good one on the XPA125. The XPA125 seems to not put out full power depending on

Hello all, I have a xiegu 5105 with updated firmware and a Xiegu xpa125B amplifier connected through the CE19 from XIegu. The amplifier and tuner work but will not give more then 95 watts output. I

I found that FlRig seems to have some nice features for tracing and logging commands. http://www.w1hkj.com/flrig-help/#ssTRACE I found this reference for the CIV command protocol for ICOM commands,

HI, HamPi can be downloaded from: https://sourceforge.net/projects/hampi/ You need to put the image on an SD card. I chose a 32GB SD card. 73, Dick? DL1CLM

Well done! Thanks so much for writing this up for us! I have been thinking about setting up my X5105 to run headless with my R-Pi 4. The main issue that I have is that the transmitter levels seem to

Hi Doug, I think for MIC input you might need a voltage divider such as this circuit on page 15 http://audiosystemsgroup.com/HamInterfacing.pdf There might be other references, but couldn’t find any

yes, line-in and line out are both ON then the audio signal from theACC connection is processed. AF_OUT and AF_IN, see manual on page 9

Is your line in/line out set to "on" in the menu setting? Just starting with the simple stuff first!

Hi everyone, I will show here the way I am active with digital mode with the X5105. The setup is very simple and works perfectly. You can use a PC with Windows 10, or use LInux. In this example, I am

In order to try FT8 with my X5105, I've been looking into setting up computer control of the radio.? And I've now gotten it to work pretty well.? But my setup has one hitch - I wasn't getting the

No, I couldn't get things to work well at all.? Especially the PTT command to go into Transmit mode.? I seemed to be having trouble with the USB adapter cable. What I'm really hoping for is to be

Bob, I echo many of the comments here about the 5105 vs the G90. based on what you described I think the 5105 is the better choice. The only advantage the G90 would give you is TX more than 5 watts if

For a possible future change of your mind, and for those who didn't notice your 5 watt note, there's some very inexpensive, small SSB linear amps available on ebay and aliexpress. *** 45W SSB

I've had all three plus others.. 83+, poor eyesight, hand tremors, etc... 1) G90 - tiny screen, small buttons that jam, no battery, no ATU, too big -- SOLD! 2) MCHF - NOT? the clone, small touch