开云体育

QTH Lesvos island abt 30km from Turkish coast. Greek north Aegean sea. KM39gc 73

Wonderfull Cliff Youre suggestion matched. Already solved.. Many thanks. Wx here we already have abt 15°C at 09:30. Expext today nearly 20°C, full sun like it has to be on the islands in Aegean sea.

Hi Erich, It sounds as if the antenna wire inside the radio has disconnected from the circuit board. This has happened on both my X1M and G90. It’s bee quite some time since I was inside my X1M

Hi Have this Rig since longer time. But used them not. Now would like tu use them for outdoor activities, and checked them in shack. I became familiar with the menues - its easy. Two issues

Hi, The inductor is very small and is part of the copper trace. Be very careful around that area especially if you have to replace the final transistor as the copper easily lifts off the board eith

Is the 100nh inductor this one in the pa stage, on attached schematic?? Any advice on where I can find it as one of the boards doesnt have any component IDs on it.? Thanks in advance!

I am glad I decided to take one more look inside before writing it off. The main jumper was upside down from where it should be and though I had read in a previous post that if it was inserted wrong

Well done. You will like it and enjoy its back to basics operation. I have only had two issues with this radio. The mic cable seems to have been poorly soldered to the plug. It stops txing. I

I went into the boards and reset the jumpers 180 degrees. Checked the connections and powered up. Keyed the mic and T appeared on the screen! Checked SWR and sent code using another radio to listen

Have a X1M which has been upgraded to Pro. Had not been used for over a year and now is not transmitting. Various post indicate a transistor failure. I am not able to do the repairs, is there anyone

Hi all, I have an original x1m that was upgraded to a pro. However, now it doesn't come on. I thought it was because I had a bad new pro faceplate but looking back at my notes it looks like I did

Thanks David.? I could use the DB9 pinout.? The cable should be here later today.? Now to find a DB9M!? Used to run down to Radio Shack or Debco Electronics here locally for such things, but no

Thanks for the url.? ?It confirmed that the serial connection will work at 3.3 volts.? ?Got one on order.? It wasn't a prime day special though.....? -- Thanks, Randy. randy.ab9go@...

I bought this one in 2021: https://www.amazon.com/gp/product/B08HLSS5T4/ And have it working with a X1M and older PI2. I had a DB9 connector from junk box (let me know if need picture of

GA Randy, In the Files section you can find a User Manual and probably a schematic to help you out. GL, John KK4ITX Visit: www.zaarc.org. ?

Hello everyone, I recently purchased an X1M but it did not come with the USB cable. What cable is suitable for this? Can I use a g90 cable and replace the 3.5 mm plug with a DB9 connector or is

Hi, I don't have an X1M, but I have just got the XPA20 which I think was designed to go with it. Has anyone here owned or used this amplifier? It powers up, and I can flick through the menues - I have

Hi group, I need help because I was updating 1.07 and the radio stopped working and I'm trying to update it and I can't. Maybe someone has a batch for this radio version 1.6

Hi, since years I did not use the X1M. Now back in HB9 - checked all.? Firmware is X1MPRO V1.024 USA from March 3.2014 Is there a newer one eg. on Github or elsewhere ? Makes 80/40/15m 6 Watts -

I have an X1M that came with the OLED Pro display.? The display recently started to have a minor but annoying issue.? The "F1" button which controls "tuning speed" and the "F2" button which controls