¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date

Re: tailstock end of Unimat alloy bed...

Andrei
 

¿ªÔÆÌåÓý

Would this work for you?




From: [email protected] <[email protected]> on behalf of Bill in OKC too via groups.io <wmrmeyers@...>
Sent: Friday, June 30, 2023 9:59 AM
To: [email protected] <[email protected]>
Subject: [Unimat] tailstock end of Unimat alloy bed...
?
In the wee hours of the night, I had an idea for an extended bed Unimat SL/DB to play with. I know some folks here have cut down an alloy bed to use the headstock end for a milling setup. I'd be interested in the rest of the bed... I want to put a set of longer rails on the bed, with the tailstock mounted to the right of the original tailstock end, so the ends are constrained. Anyone got one they'd be willing to let go for reasonable money?

Almost have my office and benchtop ready to work on my Unis.

Bill in OKC


Re: tailstock end of Unimat alloy bed...

 

He wants $50 for a useable bed. I don't want to chop one up, but know at least one got chopped some time back to make a more compact lathe & mill set up. I was perhaps a bit grouchy about it at the time, because it took me nearly 50 years to acquire one of my own. But a guy who needs a setup like that needs it, so it isn't wasting a good machine.?

And apparently they're still more common than I thought at the time, too. :) I'm a tool user,? not a tool collector. Ok, not exclusively a collector. :)

Bill in OKC?

William R. Meyers, MSgt, USAF(Ret.)

Aphorisms to live by:
Good judgement comes from experience. Experience comes from bad judgement.?
SEMPER GUMBY!
Improvise, Adapt, and Overcome.
Physics doesn't care about your schedule.
The only reason I know anything is because I've done it wrong enough times to START to know better.
Expect in one hand, expectorate in the other. See which one gets full first.



On Friday, June 30, 2023 at 11:52:09 AM CDT, Jkle379184 via groups.io <jkle379184@...> wrote:


Toms Tool Store used to sell them, I got one from him years ago for a extended bed project. Call or send him a Email.

Jeff


On Friday, June 30, 2023 at 09:59:46 AM EDT, Bill in OKC too via groups.io <wmrmeyers@...> wrote:


In the wee hours of the night, I had an idea for an extended bed Unimat SL/DB to play with. I know some folks here have cut down an alloy bed to use the headstock end for a milling setup. I'd be interested in the rest of the bed... I want to put a set of longer rails on the bed, with the tailstock mounted to the right of the original tailstock end, so the ends are constrained. Anyone got one they'd be willing to let go for reasonable money?

Almost have my office and benchtop ready to work on my Unis.

Bill in OKC


Re: Unimat SL - Vertical column & Headstock Adapter

 

you can order a hex cap screw from McMaster Carr, or Grainger, they have them in 12-1 however long you want.? Note hex head cap screw.? ?Also look under SET SCREW?

pat?


Re: tailstock end of Unimat alloy bed...

 

Toms Tool Store used to sell them, I got one from him years ago for a extended bed project. Call or send him a Email.

Jeff


On Friday, June 30, 2023 at 09:59:46 AM EDT, Bill in OKC too via groups.io <wmrmeyers@...> wrote:


In the wee hours of the night, I had an idea for an extended bed Unimat SL/DB to play with. I know some folks here have cut down an alloy bed to use the headstock end for a milling setup. I'd be interested in the rest of the bed... I want to put a set of longer rails on the bed, with the tailstock mounted to the right of the original tailstock end, so the ends are constrained. Anyone got one they'd be willing to let go for reasonable money?

Almost have my office and benchtop ready to work on my Unis.

Bill in OKC


tailstock end of Unimat alloy bed...

 

In the wee hours of the night, I had an idea for an extended bed Unimat SL/DB to play with. I know some folks here have cut down an alloy bed to use the headstock end for a milling setup. I'd be interested in the rest of the bed... I want to put a set of longer rails on the bed, with the tailstock mounted to the right of the original tailstock end, so the ends are constrained. Anyone got one they'd be willing to let go for reasonable money?

Almost have my office and benchtop ready to work on my Unis.

Bill in OKC


Re: ALERT eBay¡¯s Latest Attempt to Fleece Buyers and Sellers

 

I suspect ebay's changes to deposit money into your bank account relates to an underlining issue has been a tax issue from governments for sellers who are not reporting income.

I still enjoy the eBay marketplace, and would rather pay shipping then get into a tricky situation meeting someone in person, whom I don't know on FB Marketplace and having purchase
a few items on Marketplace this past year, my credit card company has not been very happy.

I think of eBay as a figurative box of chocolates, where you never know what you will find.... I have found some treasured items, but I remind myself it is a situation of buyer beware.

Tamra


Re: Unimat black crackle jig-saw

 

Alan, I used a TAIG Vertical slide to be able to handle the added swing.? ? here are the pictures, sorry it took so long i was on vacation. Pat


Re: ISO Steady rest

 

I use an armature dressing stone.? ?It is made of abrasive imbedded in a rubberized substrate, I chuck the armature in the drill press or hand drill, and undercut the mica with a hacksaw blade or razor saw.? ?

pat


Re: ISO Steady rest

 

And I have adequately repaired many auto generators by manually filing the armature "round" and undercutting the mica with a broken piece of fine-tooth hacksaw.? The "poor boy" method...

-Guy-?

On June 23, 2023 at 11:53 PM Charles Kinzer <ckinzer@...> wrote:

?
Here is an armature lathe designed for use in a typical auto repair shop back in the day.? Another aspect is the need to undercut the mica insulators and that is the little attachment in back in the area of the commutator.? This is a photo from an eBay listing that is handy because it has an armature from a generator mounted AND shows how the rotation is powered by a belt directly around the armature.

You could certainly use a Unimat to turn a commutator but might have to raise the head and tail stocks even higher than what is possible with the stock riser blocks.? And you would have to rig up some means to do the mica undercutting.

Inline image

Charles E. "Chuck" Kinzer

On Friday, June 23, 2023 at 08:02:45 PM PDT, Keith S. Angus <keithsangus@...> wrote:


You sometimes see a rotating chuck for use in the tailstock - they were intended to support the end of a dynamo (or motor) when skimming the commutator. I dimly recall diamond tipped tools being used for this. Wish I'd grabbed a few back when I worked with contact lenses, turned up with diamond tools on spherical turning lathes.


?


?


Re: SHERLINE TO UNIMAT 3 THREADING ATTACHMENT ADAPTER DRAWINGS

 

Hello:

Thank you for taking the time to write.


On 25 Jun 2023 at 8:41, Mike Gidley wrote:

> The chart shows the standard metric sizes. I have cut a M22x1.5
> thread with this setup
I see, the thing is in the *standard* part.? 8^)
I now recall having read that 14x1.0 is not a standard thread.

So, if I understand this correctly, to make *any* size x1.0 thread, I just
have to use the gears for the 1.0 pitch.

ie: Z50, Z25, Z25 and Z50.

The chart in the post is not Emco issue but it seems to be a copy of the
(corrected) original which was just as confusing for me.

Would have been easier to just match 'gear arrangements' to 'pitch'.

Like the thread chasers for the #150250 accessory, one for each of
the the available pitches. ?

Thank you very much for clearing this up for me.

Best,

JHM


Re: SHERLINE TO UNIMAT 3 THREADING ATTACHMENT ADAPTER DRAWINGS

 

¿ªÔÆÌåÓý

Pick a 1.0mm pitch from the chart and turn your material to 14mm then start cutting your thread.

The chart is only a guide to standard metric pitches.

I have cut a M22 x 1.5 pitch thread with this setup.

?

From: [email protected] [mailto:[email protected]] On Behalf Of Julius Henry Marx
Sent: Sunday, 25 June 2023 8:56 AM
To: Neil Morrison <neilsmorr@...>; [email protected]
Subject: Re: [Unimat] SHERLINE TO UNIMAT 3 THREADING ATTACHMENT ADAPTER DRAWINGS

?

Hello:

... in?/g/Unimat3/files

Yes, I've been there quite a few times.
But have not found anyhting on how to make a non-standard thread (like 14x1) with this accessory.
But I'l have another look.

Thanks for your input.
Best,

JHM


Re: SHERLINE TO UNIMAT 3 THREADING ATTACHMENT ADAPTER DRAWINGS

 

Hello:

... in?/g/Unimat3/files
Yes, I've been there quite a few times.
But have not found anyhting on how to make a non-standard thread (like 14x1) with this accessory.
But I'l have another look.

Thanks for your input.
Best,

JHM


Re: SHERLINE TO UNIMAT 3 THREADING ATTACHMENT ADAPTER DRAWINGS

 

Look in?/g/Unimat3/files

Neil
-----


On Sat, Jun 24, 2023 at 12:54?PM Julius Henry Marx <sawbona@...> wrote:
Hello:

I have one of the versions (plastic, not metal) of the Unimat 3 Thread Cutting Gears accessory (#150200).
From what I can make out, the gear table you have posted reads like this:


Is M10 the largest diameter that can be threaded with this accessory?

I mean ...
What is needed to get a properly installed grooving tool on the carriage/slide to move/cut towards the headstock at 1.0mm / revolution on a piece of round stock larger than M10?

Am I missing something? Most probably ... 8^¡ã

I have not been able to find a manual for this 150200 part save this chart.

Thanks in advance.

Best,

JHM


Re: SHERLINE TO UNIMAT 3 THREADING ATTACHMENT ADAPTER DRAWINGS

 

Hello:

I have one of the versions (plastic, not metal) of the Unimat 3 Thread Cutting Gears accessory (#150200).
From what I can make out, the gear table you have posted reads like this:


Is M10 the largest diameter that can be threaded with this accessory?

I mean ...
What is needed to get a properly installed grooving tool on the carriage/slide to move/cut towards the headstock at 1.0mm / revolution on a piece of round stock larger than M10?

Am I missing something? Most probably ... 8^¡ã

I have not been able to find a manual for this 150200 part save this chart.

Thanks in advance.

Best,

JHM


Re: ISO Steady rest

 

¿ªÔÆÌåÓý

Hello,

if Jeff decides not to buy the steady rest, I will.

I am located in Spain.

But Jeff has the first chance of course...

Greetings from Asturias

Frithjof

On 24/06/2023 16:04, rcjge wrote:

Ruben, that was for you btw, about the steady rest!

cheapest shipping possible, speed not issue.

Jeff


Re: ISO Steady rest

 

Ruben, that was for you btw, about the steady rest!

cheapest shipping possible, speed not issue.

Jeff


Re: ISO Steady rest

 

¿ªÔÆÌåÓý

You might say it has potential, but there again, potential (difference) seems to be what¡¯s missing.


On 24 Jun 2023, at 02:45, Scott B <sbilotta@...> wrote:

?

Hmm¡­? could this be a perpetual motion machine?

?

From: [email protected] <[email protected]> On Behalf Of Mehmood via groups.io
Sent: Friday, June 23, 2023 12:20 PM
To: [email protected]
Subject: [Unimat] ISO Steady rest

?

Brilliant idea to turn your lathe into a generator! ?Just apply electricity to the commutator and then harvest power from the plug. ?Handy if you don¡¯t have, errm, electricity.


Begin forwarded message:

From: pbrixey <pbrixey41@...>
Date: 23 June 2023 at 15:50:00 BST
To: [email protected]
Subject: Re: [Unimat] ISO Steady rest
Reply-To: [email protected], pbrixey41@...

?

Here's one I bought some years ago on eBay. I cannot find a better picture of it.

Peter Brixey in sunny Florida.

<image001.jpg>
<image001.jpg>


Re: ISO Steady rest

 

What would shipping to Canada be?

Jeff


Re: ISO Steady rest

 

This moment I have a steady rest for sale if you're interested.
Price: €70,-
I'm in the Netherlands.


Re: ISO Steady rest

 

Here is an armature lathe designed for use in a typical auto repair shop back in the day.? Another aspect is the need to undercut the mica insulators and that is the little attachment in back in the area of the commutator.? This is a photo from an eBay listing that is handy because it has an armature from a generator mounted AND shows how the rotation is powered by a belt directly around the armature.

You could certainly use a Unimat to turn a commutator but might have to raise the head and tail stocks even higher than what is possible with the stock riser blocks.? And you would have to rig up some means to do the mica undercutting.

Inline image

Charles E. "Chuck" Kinzer

On Friday, June 23, 2023 at 08:02:45 PM PDT, Keith S. Angus <keithsangus@...> wrote:


You sometimes see a rotating chuck for use in the tailstock - they were intended to support the end of a dynamo (or motor) when skimming the commutator. I dimly recall diamond tipped tools being used for this. Wish I'd grabbed a few back when I worked with contact lenses, turned up with diamond tools on spherical turning lathes.