开云体育

On Tuesday, October 22, 2024, 08:14, Rob Giuliano via groups.io <kb8rco@...> wrote:

I haven't used the configuration app in quite some time.? For TT4 variants the firmware is at V0.72, but the Config software goes back to V0.68

I do all my changes with TeraTerm now.? I use EXPORT to capture the current settings to a file, edit that file, then send the whole file back to the TT4 (or MTT4B).

I don't think there are any new settings between the 0.68 and 0.72 (except on the MTT4B version) so the configuration app should still work.

?

In other posts, users have found this process to be helpful:

1. EXPORT the current settings to a text file

2. Edit the text file according to your desire

3. RETORE to bring the TT4 (or MTT4B) to a known state

4. Send the new settings to the TT4 (or MTT4B)

?

By running RESTORE and ensuring the TT4 is in a known state, any setting that may have been causing problems should be fixed.

?

Robert Giuliano

KB8RCO

On Tuesday, October 22, 2024, 08:37, Rob Giuliano via groups.io <kb8rco@...> wrote:

While in the configuration menu you would just:

First, I found that modern serial ports and buffers may cause some timing issues so?

From the TeraTerm >Setup menu choose >Serial port ...

? ?Under Transmit Delay change the right box (msec/line) to 1.?

Then from the TeraTerm >File menu choose >Send File

Make sure the Binary box (bottom left) is "unchecked" (you are just sending the text file).

Navigate the Export file and select it, then hit <Open>.

?

If TeraTerm Local Echo is enabled, you will see the new setting followed by each settings old and new state.?

? ?{Variable} {new value}?

? ?{Variable} was {old value}?

? ?{Variable} is {new value}?

If Local Echo is unchecked, I believe you just see the old state and new state?

? ?{Variable} was {old value}?

? ?{Variable} is {new value}?

?

Robert Giuliano

KB8RCO

On Tuesday, October 22, 2024, 08:37, Rob Giuliano via groups.io <kb8rco@...> wrote:

While in the configuration menu you would just:

First, I found that modern serial ports and buffers may cause some timing issues so?

From the TeraTerm >Setup menu choose >Serial port ...

? ?Under Transmit Delay change the right box (msec/line) to 1.?

Then from the TeraTerm >File menu choose >Send File

Make sure the Binary box (bottom left) is "unchecked" (you are just sending the text file).

Navigate the Export file and select it, then hit <Open>.

?

If TeraTerm Local Echo is enabled, you will see the new setting followed by each settings old and new state.?

? ?{Variable} {new value}?

? ?{Variable} was {old value}?

? ?{Variable} is {new value}?

If Local Echo is unchecked, I believe you just see the old state and new state?

? ?{Variable} was {old value}?

? ?{Variable} is {new value}?

?

Robert Giuliano

KB8RCO

On Tuesday, October 22, 2024, 20:32, Rob Giuliano via groups.io <kb8rco@...> wrote:

Not sure if you response indicates things "DID" change or didn't change.? Did the changes you made take?

A few things in the config that need to be fixed:

????BTEXT >/WIDE1-1 PRT DIGI

What is your intent here?? This will not do anything except send a BEACON out that says

?? ?APTT4>N0KQX-11 >/WIDE1-1 PRT DIGI

NOTE:? The WIDE1-1 is not a path element, but just part of the text being sent.

My suggested changes are highlighted below.

DIGIMY TRUE????????????? This is handy for testing.? You can send a message with a path that include your callsign to test the DIGI function

PATH1? WIDE1-??????????? This provide the proper path element, so your packet will be

PATH2 WIDE2-1?????????? Use % to make sure the element is empty (I prefer WIDE2-1 so it is DIGI'ed beyond fill-ins - recommended)

TSTAT >TEST DIGI????? No real difference here, but I think the '>' just means "status"

BTEXT?>PRT DIGI ????? Moved the path element to Path1 so that the TT4 will properly use it

ALIAS1 WIDE1???????????? This turns your TT4 into a WIDE1 (fill-in) DIGI - no need for the extra '-1', the TT4 handles that

Robert Giuliano
KB8RCO

On Tuesday, October 22, 2024 at 04:05:30 PM EDT, Chiefsfan2 <chiefsfan2@...> wrote:

Ok Rob I did as you instrucked :

restored TT4

Issued Export Command?

Copied and pasted export data to a txt file

then sent file back to TT4

unpowered the TNC and powered back up.

Here is the file I sent back and only a few of these changes were made. The lat and long, paths 1 and 2 and the Tprotocal were not changed they remained default.? I am using a static location. I cant figure this out. I have experience with doing this with KPC-3 tnc's but this one I am scratching my head.?

These settings will be for a prt wide1-1 digi and I will use the gps when deployed. but for now just trying to get it to work right??

BANK 0

P300 FALSE

TXTDISP FALSE

NODISP FALSE

PPATHING FALSE

DMSDISP FALSE

MICETMV FALSE

ENTS FALSE

TELHIRES FALSE

TELVOLT TRUE

TELTEMP TRUE

PREEMPT FALSE

DIGIID TRUE

WXPOS TRUE

TELREAD TRUE

FRAWDISP FALSE

HRAWDISP FALSE

WYPTXT FALSE

PKTICOM TRUE

PKTOCOM FALSE

RPATHDISP FALSE

LEDS TRUE

PAVPEN FALSE

DEC96 FALSE

DDIST FALSE

HEADERLN FALSE

DMETRIC FALSE

SOFTRST TRUE

MSGCMD FALSE

MSGCAP FALSE

LRNTPS FALSE

GPSCHK FALSE

INTCLK FALSE

DECSTAT FALSE

DIGIMY TRUE??????????????????????????? DIGIMY FALSE

TOSV FALSE

TALT TRUE

TSPEED TRUE

TIMESTAMP TRUE

TIMEHMS TRUE

SBEN FALSE

TSWPT TRUE

AMODE GPS

BMODE GPS

ABAUD 4800

BBAUD 4800

BNKMODE 0

SSIDROUTE 0

ALTNET APTT4

MYCALL N0KQX-11

PATH1? WIDE1?????????????????????????? PATH1?

PATH2 %

PATH3 %

TSTAT>TEST DIGI????????????????????????????????????????TSTAT /TEST DIGI

BTEXT?>PRT DIGI ????????????????????????????????????? BTEXT >/WIDE1-1 PRT DIGI

BPERIOD 20

TXD 40

MTXD 10

PERSIST 65

SLOTTIME 15

QUIET 10

TRNKMODE 0

CDMODE TONES

CDLEVEL 20

TXLEVEL 128

TXTWIST 50

RXAMP 12

GWAYLEN 9

GWAYMODE NMEA

GRELAYBITS 1

GRELAYRATE 0

GKRELAY 0

LOCATION 3812.5500N 10109.5800W

GALT 1000

TSYMCODE #

TSYMTABLE \

STATUSRATE 3

PPERIOD 0

MPPERIOD 0

SBSSPEED 5

SBFSPEED 60

SBSPERIOD 1800

SBFPERIOD 90

SBTANGLE 27

SBTSLOPE 255

SBTTIME 5

MMSG 0

TSOFFSET 17

TDAO 0

TPROTOCOL APRS

TPSWITCH 0

TPERIOD 0

TVOLTTWK 128

TTEMPTWK 128

WPERIOD 0

ALIAS1 WIDE1????????????????????ALIAS1 W1

ALIAS2 %

ALIAS3 %

DUPETIME 30

FILTERCALL %

TXFREQ 144.390

RXFREQ 144.390

RXSQUELCH 0

BANK 1

P300 FALSE

TXTDISP FALSE

NODISP FALSE

PPATHING FALSE

DMSDISP FALSE

MICETMV FALSE

ENTS FALSE

TELHIRES FALSE

TELVOLT TRUE

TELTEMP TRUE

PREEMPT FALSE

DIGIID TRUE

WXPOS TRUE

TELREAD TRUE

FRAWDISP FALSE

HRAWDISP FALSE

WYPTXT FALSE

PKTICOM TRUE

PKTOCOM FALSE

RPATHDISP FALSE

LEDS TRUE

PAVPEN FALSE

DEC96 FALSE

DDIST FALSE

HEADERLN FALSE

DMETRIC FALSE

SOFTRST TRUE

MSGCMD FALSE

MSGCAP FALSE

LRNTPS FALSE

GPSCHK FALSE

INTCLK FALSE

DECSTAT FALSE

DIGIMY FALSE

TOSV TRUE

TALT TRUE

TSPEED TRUE

TIMESTAMP TRUE

TIMEHMS TRUE

SBEN FALSE

TSWPT TRUE

AMODE GPS

BMODE GPS

ABAUD 4800

BBAUD 4800

BNKMODE 0

SSIDROUTE 0

ALTNET APTT4

MYCALL NOCALL

PATH1 WIDE1-1

PATH2 WIDE2-1

PATH3 %

TSTAT /TinyTrak4 Alpha

BTEXT >/TinyTrak4 Alpha

BPERIOD 0

TXD 40

MTXD 10

PERSIST 65

SLOTTIME 15

QUIET 10

TRNKMODE 0

CDMODE TONES

CDLEVEL 20

TXLEVEL 128

TXTWIST 50

RXAMP 12

GWAYLEN 9

GWAYMODE NMEA

GRELAYBITS 1

GRELAYRATE 0

GKRELAY 0

LOCATION 1234.5678N 12345.6789W

GALT 1000

TSYMCODE >

TSYMTABLE /

STATUSRATE 1

PPERIOD 0

MPPERIOD 0

SBSSPEED 5

SBFSPEED 60

SBSPERIOD 1800

SBFPERIOD 90

SBTANGLE 27

SBTSLOPE 255

SBTTIME 5

MMSG 0

TSOFFSET 17

TDAO 0

TPROTOCOL MIC-E

TPSWITCH 0

TPERIOD 0

TVOLTTWK 128

TTEMPTWK 128

WPERIOD 0

ALIAS1 TEMP

ALIAS2 %

ALIAS3 %

DUPETIME 30

FILTERCALL %

TXFREQ 144.390

RXFREQ 144.390

RXSQUELCH 0

On Tuesday, October 22, 2024, 22:12, Rob Giuliano via groups.io <kb8rco@...> wrote:

If you change them one at a time in TeraTerm, they don't take either?

Did you set the Transmit Delay? box (msec/line) to 1 in TerTerm?

What does the output look like in TeraTerm?? Does it look like characters are missing?

Robert Giuliano
KB8RCO

On Tuesday, October 22, 2024 at 09:38:28 PM EDT, Chiefsfan2 <chiefsfan2@...> wrote:

No they didn’t take. These settings are intended for a portable digi local not meant to go anywhere but one local digipeat. Ok will note these settings. I’m having a zoom with byonics to help me out also. Thanks