Re: What can you do with a 1502?
Hi. Several years ago, I, (for some bizarre reason) became rather obsessed with TDRs. I have 3 towers at my location with antennas from 160M through 70CM. I was able to accumulate a LOT of 1502 and
By
[email protected] <bonddaleena@...>
·
#145089
·
|
Re: Problems with MG Chemicals Super Contact Clearer
Out of curiosity, did you try BOTH ends of the nozzle? --Eric Sent from my Samsung Galaxy S8.
By
EricJ
·
#145088
·
|
Re: Problems with MG Chemicals Super Contact Clearer
Hi Stan, I use MG Chemical Super Wash, part number 406B-425G. I just removed and inserted the current tube a loose tube (spare, taped to the can) in my can's nozzle... works like a charm. It IS a
By
Phillip Potter <p.potter@...>
·
#145087
·
|
Re: What can you do with a 1502?
Not just breaks, any discontinuity. I've used it to diagnose a fault in a relative's 75ohm TV antenna feed, where one multiplex couldn't be received. There was a bad kink 4m into the cable, and the
By
Tom Gardner
·
#145086
·
|
Re: 16700A setting up Xwindows.
Hello all, Mine is a NEC 3x that uses a CD Carrier. Remember those!! 16700s do not have Displays. This is from an expert that explained the terminology to me. The As came with Ethernet 10baseTs and no
By
Richard R. Pope
·
#145085
·
|
Re: Where to find a serial number on a 335 Sony/Tektronix
Then it fell off... there is a slot, but no SN plate. You can see that, here: /g/TekScopes/album?id=33014 so, I guess the search is over.? Come to think of it, I have a vague
By
Phillip Potter <p.potter@...>
·
#145084
·
|
Re: Where to find a serial number on a 335 Sony/Tektronix
Should be under the external trigger input BNC on the side. Paul -- Paul Amaranth, GCIH | Rochester MI, USA Aurora Group, Inc. | Security, Systems & Software paul@... | Unix & Windows
By
Paul Amaranth
·
#145083
·
|
Re: What can you do with a 1502?
Thanks Harvey, I'm aware of the TD issue. Frankly, I was surprised that it was OK. There was a thread on eevblog where one fellow used a Russion 1|308E as the 20mA and a A|201V for the 10mA diode.
By
Paul Amaranth
·
#145082
·
|
Where to find a serial number on a 335 Sony/Tektronix
Hi all, I searched to exterior, and the interior, but could not find a SN for my 335. The reason for the search is, I have two 335 manuals a want to figure out which one to keep.? One has part number
By
Phillip Potter <p.potter@...>
·
#145081
·
|
Re: What can you do with a 1502?
You are quite lucky. The tunnel diode is very fragile and directly connected to the BNC. (I'm thinking of the 1502, not sure about the later revisions). There should be a shorting BNC connector that
By
Harvey White
·
#145080
·
|
Re: What can you do with a 1502?
Hi Paul, It has lots of uses. Get the Tek book Time Domain Reflectrometry Measurements for insights. I use it to test every cable, connector, and adapter I buy from ham fests the Chinese, and anyone
By
Dennis Tillman W7pF
·
#145079
·
|
Re: Problems with MG Chemicals Super Contact Clearer
Hi Stan, I had the same problem just yesterday on a new MG Chemicals Super Contact Cleaner I bought. On my own I figured that I would have more success by removing the nozzle. That was the case, but
By
Dennis Tillman W7pF
·
#145078
·
|
What can you do with a 1502?
I pulled a 1502 TDR out of the buck a pound box at Dayton a few years back and finally got it completely fixed the other week. I had to fab a battery pack and then fix the charging circuitry, but
By
Paul Amaranth
·
#145077
·
|
Re: 7623A + 7A26 + 7B53
Thank you all guys, for the advice... David... any particular reason why you specified "and the TB triggers OK"? I mean... the video that the owner posted...(here:
By
Fabio Trevisan
·
#145076
·
|
Re: 7623A + 7A26 + 7B53
If it powers on and works and the TB triggers OK, than just buy it. Dave
By
David C. Partridge
·
#145075
·
|
Re: 7623A + 7A26 + 7B53
I have a 7623 (not A) + 7A26 + 7B53A and I have no real complaints, though the mainframe could probably do with some attention to cure a minor display instability ¡ª probably due to dirty or loose
By
Dave Voorhis
·
#145074
·
|
Problems with MG Chemicals Super Contact Clearer
Hello the forum, Relevance to Forum, it is used in cleaning switches in Tektronix equipment. I bought a can of this product, 801B-125G. The spray tube just will not insert. Like many of you, I have
By
brasscat
·
#145073
·
|
Re: 7623A + 7A26 + 7B53
I have the same combination along with a big bunch of other plugins. This is a one setup that I use quite often, sometimes with a non Tek curve tracer . I have had this for many years and I think its
By
Bert Haskins
·
#145072
·
|
Re: 7623A + 7A26 + 7B53
Decent enough, although I'm not an owner of the 7600 series. Take two or three BNC cables and a T. That ought to let you get a good view of the calibrator waveform. Swapping slots is another good
By
Harvey White
·
#145071
·
|
Re: TekWiki Helper Idea. Brainstorm or Washout?
Hi Kurt, I can dig up the names of the designers of some of the Tek instruments. I may even be able to get in touch with some of them to see if they were willing to share the history of the
By
Dennis Tillman W7pF
·
#145070
·
|