Keyboard Shortcuts
Likes
- TailwindForum
- Messages
Search
|
Re: Harmon Lang gear
What's your address... off groups? I only have the mains. Mike On Sun, Apr 6, 2025, 12:21?PM dumona via <dumona=[email protected]> wrote:
|
|
Re: Harmon Lang gear
I have gear legs from an RV7A if interested. On Sun, Apr 6, 2025, 11:13?AM dumona via <dumona=[email protected]> wrote:
|
|
Flight Analysis Software
I was browsing my aviation YouTube channels and came across this website mentioned on Cleared Direct.? It is ?
I've only played around with it for a couple of minutes, but it is really cool!? It can take your EFIS data and analyze and replay it, and Keith, it does work with our GRT units. You can get takeoff and landing performance, it provides warnings of your flight (too close to stall, traffic, potential wake turbulence, oscillations in flare, centerline deviation...).? It would be great for a CFI to review with a student, but it also would be great for phase1 flight analysis.
You can replay your flight in real-time with a realistic out the window view.? The website is free.? You do have to set up an account and then you can just drag and drop your flight data.? It will also use ADSB data if you don't have an EFIS. |
|
Re: Harmon Lang gear
Good to know, thanks for the info. Mike On Sun, Apr 6, 2025, 6:10?AM WILLIAM via <bbernard1945=[email protected]> wrote:
|
|
Re: Harmon Lang gear
If you are ordering a set of custom gear legs, be aware that the 1 1/4" axle size is"nominal". If the axle is made to that exact dimension the wheel won't fit. The axle needs to be a couple of thousandths undersize.
?
I found this out the hard way when I ordered my gear legs.
?
Also Cleveland wheels are about 1/4" wider than the ones Vans uses.
?
Bill Bernard
|
|
Re: Harmon Lang gear
I'm using it on a light W8. On Sat, Apr 5, 2025, 5:00?PM Tailwind14855 via <Tailwind14855=[email protected]> wrote:
|
|
Re: Harmon Lang gear
¿ªÔÆÌåÓýI can¡¯t answer for all, but these that I just checked are 1 ?¡± Red ? From: [email protected] <[email protected]> On Behalf Of Michael Richardson via groups.io
Sent: Saturday, April 5, 2025 2:09 PM To: [email protected] Subject: Re: [TailwindForum] Harmon Lang gear ? Axle sizes on all W8s and W10s were 1.250", right? ? On Sat, Apr 5, 2025, 3:48?PM red via <redswing=[email protected]> wrote:
|
|
Re: Harmon Lang gear
W8 and W10 both 1 1/4 axle diameter. W8 is 3/4" diameter at the small end of taper, recommended to use 7/8 for W10.?
On Saturday, April 5, 2025 at 02:30:56 PM MST, red via groups.io <redswing@...> wrote:
I think so, I can verify that on these and report Red ? From: [email protected] <[email protected]> On Behalf Of Michael Richardson via groups.io
Sent: Saturday, April 5, 2025 2:09 PM To: [email protected] Subject: Re: [TailwindForum] Harmon Lang gear ? Axle sizes on all W8s and W10s were 1.250", right? ? On Sat, Apr 5, 2025, 3:48?PM red via <redswing=[email protected]> wrote:
|
|
Re: Harmon Lang gear
¿ªÔÆÌåÓýI think so, I can verify that on these and report Red ? From: [email protected] <[email protected]> On Behalf Of Michael Richardson via groups.io
Sent: Saturday, April 5, 2025 2:09 PM To: [email protected] Subject: Re: [TailwindForum] Harmon Lang gear ? Axle sizes on all W8s and W10s were 1.250", right? ? On Sat, Apr 5, 2025, 3:48?PM red via <redswing=[email protected]> wrote:
|
|
Re: Harmon Lang gear
Axle sizes on all W8s and W10s were 1.250", right? On Sat, Apr 5, 2025, 3:48?PM red via <redswing=[email protected]> wrote:
|
|
Re: Harmon Lang gear
¿ªÔÆÌåÓýOK, do we have your address? Red ? From: [email protected] <[email protected]> On Behalf Of Michael Richardson via groups.io
Sent: Saturday, April 5, 2025 1:34 PM To: [email protected] Subject: Re: [TailwindForum] Harmon Lang gear ? Red, I will take those. Mike ? On Sat, Apr 5, 2025, 3:32?PM red via <redswing=[email protected]> wrote:
|
|
Re: Harmon Lang gear
Red, I will take those. Mike On Sat, Apr 5, 2025, 3:32?PM red via <redswing=[email protected]> wrote:
|
|
Re: Harmon Lang gear
¿ªÔÆÌåÓýI have a pair that would be good for a W-8, $150 plus shipping at cost. Please reply off forum, Red ? From: [email protected] <[email protected]> On Behalf Of Christian Bobka via groups.io
Sent: Saturday, April 5, 2025 11:52 AM To: [email protected] Subject: Re: [TailwindForum] Harmon Lang gear ? Dan. W8 or W10? ? On Sat, Apr 5, 2025 at 9:35?AM helspersew@... via <Helspersew=[email protected]> wrote:
|
|
Re: Harmon Lang gear
Dan. W8 or W10?
|
