开云体育

moyer marine for atomic 4 parts and info --- chiliwind <chiliwind@...> wrote: ____________________________________________________________________________________ Boardwalk for $500? In 2007?

Check with Don Moyer at moyer marine on the gear drive. He is the east coast A4 guru. I had the cutlass bearing changed on hull # 545 by Beatons in NJ. --- chiliwind <chiliwind@...> wrote:

Hello everyone, My name is Matthias and I'm trying to find contact information for Russel Cobb. He has been (or still is) sailing his Tartan 27 named "Hygelig" around the world. Since I have similar

Does any one out there have any access to replacement parts for the Paragon gear drive on my Atomic 4 ? I have hull 524 and some vibration in the drive line. PS Has anyone ever changed out the cutlass

Anyone have any ideas where to get screens for the ports. Mine is a 1970 T-27 hull #442

Thanks: I am planning to pull the boat out next spring and this is one of the things I want tocheck.. armando --- Matthew Leahy <mp_leahy@...> wrote:

Armando, My cb was stuck, no, it was as if it had been bolted up. The rust expanded and pinched the board fast in its pocket. The yard pulled the pivot pin, tipped the forward end of the board down,

I have hull 555 1974. Does this means my cb could be also in this conditions. I have to admit I have not inspected it for a long long time am --- mp_leahy <mp_leahy@...> wrote:

I have a used centerboard from a 1975 T27. It is rust swollen and split for about 4 inches around the pennant. My boat yard said it could be repaired for about $750 at $50 per hour (when was the last

I used the West Marine pump. There was another brand (rule) in there previously. The PO had used garden hose and secured a board in the bottom of the hull that it and the float switch sat on. I used a

I consider myself a newbie. My first boat was a Mac 25 (not the motor sailor)very light and trailerable. I have it at a marina in florida and have been getting to know the other sailors. Lots of fun

Here's their U.S. contact for the "Whale Supersub 500" Whale Water Systems Inc. 100 Corporate Place, Suite 402, Peabody, MA 01960, USA Tel: 978-531-0021 Fax: 978-531-1017 usasales@...

I have the magazine with that test in it. I'd love to get one of the Supersubs but when I check online, most are in the UK... Where did you get your's?

I just posted an article we did on "Bilgepump" where tested 10 pumps. The Whale Supersub 500 was our winner, and that's the one I ended up installing in my T27. It fits well because it is narrow but

I have a manual Whale Gusher Titan pump, bulkhead mounted on side of cockpit. (and a bucket:) --Bill #327 <henrymarcucella@...> wrote:

I need to replace my old peters and russell manual bilge pump. I would like to hear what other t27 owners use as a bilge pump

39-13/16" from outside of mast to centerline of shroud hole. Note: this is for a T27-2. I don't know if this holds for T27s. Jack Wyman 1978 T27-2 "Seakindly" #667 Manchester, MI

That is AWESOME !!!!!!!!!!!!!!! cONGRATS ! chrisd4700 <chrisd4700@...> wrote: Well Everyone, I must be living right... At the same time my boat was hurling down the highway, My older brother was

Well Everyone, I must be living right... At the same time my boat was hurling down the highway, My older brother was about 8 hrs. behind him on a surprise trip down to see me. He and his son were just

Thanks Bill, My mast is also very close to the size of the opening. I'm thinking of using Spar Tite in that opening. My buddy just used it on his Pearson 10M and it's a really nice product that is