开云体育

Help with hand wheel

nonparadigm All Messages By This Member #107519 Son and I rebuilding 14-1/2’’ and need apron hand wheel, can't find an original but can get a cast iron wheel that looks close fairly cheap. Can someone tell us the size of original wheel, part book no help listed as NLA. Also is either 13’’ or 16’’ a match? Apron has a hub sticking out 2-1/4’’, shaft is 5/8’’diameter and sticks out 1-1/4’’ with through hole for pin. Hope this helps? Any help would be greatly appreciated and thank you. Dennis
[email protected] All Messages By This Member #107523 开云体育 Going to the railway shortly. Will try to remember to photograph & measure ours. Eddie toggle quoted message Show quoted text ------ Original Message ------ From: "nonparadigm via groups.io" <nonparadigm@...> To: "[email protected]" <[email protected]> Sent: Saturday, 8 Apr, 23 At 22:57 Subject: [SouthBendLathe] Help with hand wheel Son and I rebuilding 14-1/2’’ and need apron hand wheel, can't find an original but can get a cast iron wheel that looks close fairly cheap. Can someone tell us the size of original wheel, part book no help listed as NLA. Also is either 13’’ or 16’’ a match? Apron has a hub sticking out 2-1/4’’, shaft is 5/8’’diameter and sticks out 1-1/4’’ with through hole for pin. Hope this helps Any help would be greatly appreciated and thank you. Dennis
fred eisner All Messages By This Member #107526 开云体育 hi dennis i have a???doz original sb hand wheels in various sizes what size do you need fred imsteamer21@... 914 720 5523 toggle quoted message Show quoted text ------ Original Message ------ From: "nonparadigm via groups.io" <nonparadigm@...> To: "[email protected]" <[email protected]> Sent: Saturday, 8 Apr, 23 At 22:57 Subject: [SouthBendLathe] Help with hand wheel Son and I rebuilding 14-1/2’’ and need apron hand wheel, can't find an original but can get a cast iron wheel that looks close fairly cheap. Can someone tell us the size of original wheel, part book no help listed as NLA. Also is either 13’’ or 16’’ a match? Apron has a hub sticking out 2-1/4’’, shaft is 5/8’’diameter and sticks out 1-1/4’’ with through hole for pin. Hope this helps Any help would be greatly appreciated and thank you. Dennis
[email protected] All Messages By This Member #107532 开云体育 Hi Dennis & Fred, Please see attached for the carriage handwheel on our 1943 built 14.5 x 6' toolroom at the Golden valley Light Railway, UK. Might look tatty, but is actually in superb condition having been rebuilt by Sentinel at Shrewsbury in 1961 and little used since. There may well be a few of these brand new at the bottom of the Atlantic... Eddie toggle quoted message Show quoted text ------ Original Message ------ From: "nonparadigm via groups.io" <nonparadigm@...> To: "[email protected]" <[email protected]> Sent: Saturday, 8 Apr, 23 At 22:57 Subject: [SouthBendLathe] Help with hand wheel Son and I rebuilding 14-1/2’’ and need apron hand wheel, can't find an original but can get a cast iron wheel that looks close fairly cheap. Can someone tell us the size of original wheel, part book no help listed as NLA. Also is either 13’’ or 16’’ a match? Apron has a hub sticking out 2-1/4’’, shaft is 5/8’’diameter and sticks out 1-1/4’’ with through hole for pin. Hope this helps Any help would be greatly appreciated and thank you. Dennis 14.5 inch carriage hendwheel 3.JPG 14.5 inch carriage hendwheel 2.JPG 14.5 inch carriage hendwheel 1.JPG
[email protected] All Messages By This Member #107533 开云体育 I forgot to mention. I measured the ends of the taper pin that holds it in place. It only just sticks through both sides. Large end 0.23", small end 0.20". Obviously you will probably have to ream through lightly. to get a good fit on the new pin, so BEWARE: Imperial standard taper pins & reamers are 1/4" per foot, i.e. 1 in 48, whereas metric ones are 1 in 50. Don't know where you are, but in the UK, the current retail default is metric. I also noticed that for some reason, ours also has a small Allen grub screw at about 90 degrees to the pin, and I have no intention whatsoever of opening that potential can of worms until I have to! Cheers, Eddie toggle quoted message Show quoted text ------ Original Message ------ From: "eddie.draper@... via groups.io" <eddie.draper@...> To: [email protected] Sent: Monday, 10 Apr, 23 At 09:38 Subject: Re: [SouthBendLathe] Help with hand wheel Hi Dennis & Fred, Please see attached for the carriage handwheel on our 1943 built 14.5 x 6' toolroom at the Golden valley Light Railway, UK. Might look tatty, but is actually in superb condition having been rebuilt by Sentinel at Shrewsbury in 1961 and little used since. There may well be a few of these brand new at the bottom of the Atlantic... Eddie ------ Original Message ------ From: "nonparadigm via groups.io" <nonparadigm@...> To: "[email protected]" <[email protected]> Sent: Saturday, 8 Apr, 23 At 22:57 Subject: [SouthBendLathe] Help with hand wheel Son and I rebuilding 14-1/2’’ and need apron hand wheel, can't find an original but can get a cast iron wheel that looks close fairly cheap. Can someone tell us the size of original wheel, part book no help listed as NLA. Also is either 13’’ or 16’’ a match? Apron has a hub sticking out 2-1/4’’, shaft is 5/8’’diameter and sticks out 1-1/4’’ with through hole for pin. Hope this helps Any help would be greatly appreciated and thank you. Dennis

Previous Topic Next Topic