开云体育

PI Teensy TNC G8BPQ K2MJM v4 Issues

Mike - KB0FX #12583 I have a PI Teensy TNC G8BPQ K2MJM v4 I am trying to get working with a Raspberry Pi 3B+ . This board has a Teensy 3.6. I have been able to use the firmware loader to install Pi9K Raspberry Pi Firmware Tennsy36 0416202.hex. Once attached to the RPI I am unable to communicate with the PI TNC via the serial port using pitnc_getparms. Has anyone else worked with this board? Thanks Mike -KB0FX
Mat Murdock All Messages By This Member #12585 Make sure you have enabled?serial port on the pi. sudo raspi-config Option 5 - Turn on SSH and Serial interface, No for login shell of serial, Yes for enabling hardware Finish sudo reboot It would also be good to post what the exact command is you are trying to run. Mat toggle quoted message Show quoted text On Fri, Dec 4, 2020 at 10:14 AM Mike - KB0FX <mweilb@...> wrote: I have a PI Teensy TNC G8BPQ K2MJM v4 I am trying to get working with a Raspberry Pi 3B+ . This board has a Teensy 3.6. I have been able to use the firmware loader to install Pi9K Raspberry Pi Firmware Tennsy36 0416202.hex. Once attached to the RPI I am unable to communicate with the PI TNC via the serial port using pitnc_getparms. Has anyone else worked with this board? Thanks Mike -KB0FX
Mike - KB0FX #12588 Matt - Thanks for the quick response! I have verified that logging is turned off to the serial port. I am trying to run?pitnc_get/setparams and it just keeps trying and trying. The V4 board JP3 & JP4 heards on have three pins. I have pins 1 & 2 jumpered on both headers. Is that correct?? 73 - Mike - KB0FX toggle quoted message Show quoted text On Fri, Dec 4, 2020 at 12:08 PM Mat Murdock <mat.murdock@...> wrote: Make sure you have enabled?serial port on the pi. sudo raspi-config Option 5 - Turn on SSH and Serial interface, No for login shell of serial, Yes for enabling hardware Finish sudo reboot It would also be good to post what the exact command is you are trying to run. Mat On Fri, Dec 4, 2020 at 10:14 AM Mike - KB0FX <mweilb@...> wrote: I have a PI Teensy TNC G8BPQ K2MJM v4 I am trying to get working with a Raspberry Pi 3B+ . This board has a Teensy 3.6. I have been able to use the firmware loader to install Pi9K Raspberry Pi Firmware Tennsy36 0416202.hex. Once attached to the RPI I am unable to communicate with the PI TNC via the serial port using pitnc_getparms. Has anyone else worked with this board? Thanks Mike -KB0FX
N5XMT All Messages By This Member #12589 is your serial port baudrate set to 115200? toggle quoted message Show quoted text On Fri, Dec 4, 2020 at 12:02 PM Mike - KB0FX <mweilb@...> wrote: Matt - Thanks for the quick response! I have verified that logging is turned off to the serial port. I am trying to run?pitnc_get/setparams and it just keeps trying and trying. The V4 board JP3 & JP4 heards on have three pins. I have pins 1 & 2 jumpered on both headers. Is that correct?? 73 - Mike - KB0FX On Fri, Dec 4, 2020 at 12:08 PM Mat Murdock <mat.murdock@...> wrote: Make sure you have enabled?serial port on the pi. sudo raspi-config Option 5 - Turn on SSH and Serial interface, No for login shell of serial, Yes for enabling hardware Finish sudo reboot It would also be good to post what the exact command is you are trying to run. Mat On Fri, Dec 4, 2020 at 10:14 AM Mike - KB0FX <mweilb@...> wrote: I have a PI Teensy TNC G8BPQ K2MJM v4 I am trying to get working with a Raspberry Pi 3B+ . This board has a Teensy 3.6. I have been able to use the firmware loader to install Pi9K Raspberry Pi Firmware Tennsy36 0416202.hex. Once attached to the RPI I am unable to communicate with the PI TNC via the serial port using pitnc_getparms. Has anyone else worked with this board? Thanks Mike -KB0FX
John G8BPQ All Messages By This Member #12590 开云体育 If you hold the board with the Pi edge connector to the top and the USB connection to the left then the jumpers are fitted horizontally on? the right hand pair of pins. 73, John G8BPQ On 04/12/2020 19:01, Mike - KB0FX wrote: toggle quoted message Show quoted text Matt - Thanks for the quick response! I have verified that logging is turned off to the serial port. I am trying to run?pitnc_get/setparams and it just keeps trying and trying. The V4 board JP3 & JP4 heards on have three pins. I have pins 1 & 2 jumpered on both headers. Is that correct?? 73 - Mike - KB0FX On Fri, Dec 4, 2020 at 12:08 PM Mat Murdock <mat.murdock@...> wrote: Make sure you have enabled?serial port on the pi. sudo raspi-config Option 5 - Turn on SSH and Serial interface, No for login shell of serial, Yes for enabling hardware Finish sudo reboot It would also be good to post what the exact command is you are trying to run. Mat On Fri, Dec 4, 2020 at 10:14 AM Mike - KB0FX <mweilb@...> wrote: I have a PI Teensy TNC G8BPQ K2MJM v4 I am trying to get working with a Raspberry Pi 3B+ . This board has a Teensy 3.6. I have been able to use the firmware loader to install Pi9K Raspberry Pi Firmware Tennsy36 0416202.hex. Once attached to the RPI I am unable to communicate with the PI TNC via the serial port using pitnc_getparms. Has anyone else worked with this board? Thanks Mike -KB0FX
Clinton VE7KNL All Messages By This Member #12626 The jumpers should be on pins 2 & 3 if it's used as a Pi Hat. Page 15.

Previous Topic Next Topic