开云体育

Hi Srdjan! It looks to me, like some gorillalilla! Ripped the pins off the BNC connector!?! It's a mystery how some miscreant could rip the pins off! Or shear them off with a pipe wrench? Other than

If you mean R80 on the VRM5080C or VRM5080S RX module it's 10 ohm 1/4 watt metal oxide. Regards Dave g1jwg

Greetings if anybody has a schematic of the RX board on vrm 5090 i need the value of resistor R80 mines black! wd8axa

Ok folks, I found a box in the garage with some more goodies. Time to sell 'em. Shipping is additional to these prices. I will ship this stuff USPS priority. Not the cheapest, but convenient as I get

Not Racal but I wonder if anyone can help with a Pye Solent PTC984 service manual or copy thereof. regards Dave g1jwg

Hi Group, I am looking to purchase the DC Battery connection stubs for the PRM-4021. Please contact me directly to my email or WhatsApp: galiaf1@... WhatsApp: +972-54-313-6944 Thanks & 73s Ilan

Folks, I’mlooking for a Jag-V rear 10 way Dogbone radio to amplifier cable. The cable for the older Mk1 “vertical” sets as opposed to the later horizontal ones. Any help really

RA.2000 wanted in working and nice cosmetic condition. Must have the PSTN option. Purchase, or exchange Clansman items.? Best regards,? Bob

Hello, I was looking at charging the MA948 battery for my TRA 921 through the audio connector. Before I did so, I noticed the wiring on the bottom of the case does not appear to be complete. Looking

Mike, I am not familiar with the charger but I do have a suggestion regarding the bulbs, that is, if you can't find replacements. If they are bad, you could sacrifice the glass and filament with a set

Have a charger here. -- -- Ira J. Moser, Owner, MECO TEL: (425) 788-0208 WEB: www.meco.org EMAIL: ira@... Orwell was an OPTIMIST!

This charger is for 12/24v batteries and has adaptors for many such as Clansman It has two pilot lights with a bulb size around LES, however the thread seems to be different Designation seems to be

Good morning all. I got my hands on a CODAN 8528 radio and some accessories. Unfortunately, the 15-pin plug of the CODAN 9366HF SSB TRANCEIVER remote control is torn off. I do not find on the canvas

Hello everyone. I am new here and very pleased that I found this group. I have a VRQ316 (BCC66HE with BCC567HG VIU) and I'm trying to get it working and use it as my HAM radio for 6m band. I have the

John: THANK YOU. I will check those areas the next time ! I do hear relays clicking when the PTT is pressed. Nevertheless I will check. I got my spectrum analyser up and running, the tx frequency

TRA931 RelaysFrom my recollection relay failures in the TRA931 wherefairly rare, unlike what some self-appointed points of knowledge of all thingsRacal on this forum claim repeatedly. In the 25 years

I used LiPo batteries for my RC planes. Very reasonable pricing. Cant beat the power /weight or power/volume. Cheapest battery size is 3 series 2200mAH packs, 12.6V fully charged. On a sale such a

Syncal-30 is a complex set so you cannot expect a simple answer like "it's C23". You must get the circuit printed out with the parts locator diagram and work through it. Start with PSU voltages. You

It seems to tx about 1 MHz lower than it should. If the dials are set to 15MHz, it outputs around 14 MHz if my spectrum analyser is correct. I took the shields off of the radio and noticed that both

Did some more checking, the TX is transmitting but no where? near the set frequency. Have to warm up the spectrum analyser. Any hints ? where to start ?