开云体育

#qmx SSB Firmware beta 1_01_005 release

#qmx

Dj Merrill All Messages By This Member #143918 On Fri, Apr 25, 2025 at 03:49 PM, Hans Summers wrote: Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows. We will hear from you in a few days after it finishes patching...? ;-) ?
Hans Summers All Messages By This Member #143920 Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows. We will hear from you in a few days after it finishes patching...? ;-) For reasons best known only to itself, Win 10 didn't do any patching even though it's been years since I used it. And it even seemed to boot in only about 7 minutes which is much faster than I recall. Though still woefully slower than the 10 seconds it takes the same machine to boot into Linux.? I'm pleased to report that setting USB Serial ports to both 1 and 2 both worked, with both serial and sound. TeraTerm is apparently what's on the desktop and I could connect to both ports with no difficulty, and sound too.? Setting USB Serial ports to 3 did not work (as we know from 1_01_004).? So all: please standby while I prepare and upload a .QMX file with high confidence, and my apologies for not thinking of booting my computer into Win10 until now and wasting your time on it.? 73 Hans G0UPL
Stan Dye All Messages By This Member #143921 On Fri, Apr 25, 2025 at 01:01 PM, Hans Summers wrote: Setting USB Serial ports to 3 did not work (as we know from 1_01_004). But for some of us, all 3 ports were working fine in Win10 (fully patched Win10 home edition) in 1_01_004.
Hans Summers All Messages By This Member #143922 Hi Stan Setting USB Serial ports to 3 did not work (as we know from 1_01_004). But for some of us, all 3 ports were working fine in Win10 (fully patched Win10 home edition) in 1_01_004. Then I expect that should also be the case in 1_01_005. My Win10 is very old, remember. In Linux I see the three ports and Audio no problem (and USB Flash drive, if I enable that in the firmware).? 73 Hans G0UPL
mux_folder2001 All Messages By This Member #143923 开云体育 You mnade me do it. Booted my W11 machine. Less than 1 minute to log in screen. Probably 90 seconds until I was typing this email. Tony AD0VC toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of Hans Summers via groups.io <hans.summers@...> Sent: Friday, April 25, 2025 2:01 PM To: [email protected] Notification <[email protected]> Subject: Re: [QRPLabs] #qmx SSB Firmware beta 1_01_005 release ? Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows. We will hear from you in a few days after it finishes patching...? ;-) For reasons best known only to itself, Win 10 didn't do any patching even though it's been years since I used it. And it even seemed to boot in only about 7 minutes which is much faster than I recall. Though still woefully slower than the 10 seconds it takes the same machine to boot into Linux.? I'm pleased to report that setting USB Serial ports to both 1 and 2 both worked, with both serial and sound. TeraTerm is apparently what's on the desktop and I could connect to both ports with no difficulty, and sound too.? Setting USB Serial ports to 3 did not work (as we know from 1_01_004).? So all: please standby while I prepare and upload a .QMX file with high confidence, and my apologies for not thinking of booting my computer into Win10 until now and wasting your time on it.? 73 Hans G0UPL
Stan Dye All Messages By This Member #143924 On Fri, Apr 25, 2025 at 01:10 PM, Hans Summers wrote: Then I expect that should also be the case in 1_01_005. Except in the current 1_01_005 I have the same problem as everyone else, the USB device is unrecognized due to 'Configuration Descriptor Request Failed'.? The fix you just made should remedy that, so maybe my machine won't have the problem with 3 ports like yours.
Frank Fertitta AA5IT All Messages By This Member #143926 Mine doesn't work with .005. The serial port is not recognized. Win11. Back to .003, everything's fine.
Hans Summers All Messages By This Member #143927 Hi Stan 1_01_006 is on the website... so let me know how it goes! By the way - all noted on remembering the last-visited sub-menu selections, leave that one with me. 73 Hans G0UPL toggle quoted message Show quoted text On Fri, Apr 25, 2025 at 11:14?PM Stan Dye via <standye=[email protected]> wrote: On Fri, Apr 25, 2025 at 01:10 PM, Hans Summers wrote: Then I expect that should also be the case in 1_01_005. Except in the current 1_01_005 I have the same problem as everyone else, the USB device is unrecognized due to 'Configuration Descriptor Request Failed'.? The fix you just made should remedy that, so maybe my machine won't have the problem with 3 ports like yours.
Frank Fertitta AA5IT All Messages By This Member #143928 Sorry, Hans, I didn't realize the code was being changed as I typed.
mux_folder2001 All Messages By This Member #143931 开云体育 1 works, 2 works, but 3 ports results in no com ports. Tony AD0VC toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of Hans Summers via groups.io <hans.summers@...> Sent: Friday, April 25, 2025 2:17 PM To: [email protected] <[email protected]> Subject: Re: [QRPLabs] #qmx SSB Firmware beta 1_01_005 release ? Hi Stan 1_01_006 is on the website... so let me know how it goes! By the way - all noted on remembering the last-visited sub-menu selections, leave that one with me. 73 Hans G0UPL On Fri, Apr 25, 2025 at 11:14?PM Stan Dye via <standye=[email protected]> wrote: On Fri, Apr 25, 2025 at 01:10 PM, Hans Summers wrote: Then I expect that should also be the case in 1_01_005. Except in the current 1_01_005 I have the same problem as everyone else, the USB device is unrecognized due to 'Configuration Descriptor Request Failed'.? The fix you just made should remedy that, so maybe my machine won't have the problem with 3 ports like yours.
Hans Summers All Messages By This Member #143932 Hi Tony 1 works, 2 works, but 3 ports results in no com ports. Ok that will be another thing for me to investigate then, considering that 3 worked for you in 1_01_004.? I'm keen to hear from Ludwig about Win7... 73 Hans G0UPL
Hans Summers All Messages By This Member #143933 P.S. Tony please run 30m calibrarion and screenshot it at DAC 300 (or thereabouts) and again at it's completion or however far it gets.? 73 Hans G0UPL toggle quoted message Show quoted text On Fri, Apr 25, 2025, 23:35 QRP Labs <hans.summers@...> wrote: Hi Tony 1 works, 2 works, but 3 ports results in no com ports. Ok that will be another thing for me to investigate then, considering that 3 worked for you in 1_01_004.? I'm keen to hear from Ludwig about Win7... 73 Hans G0UPL
mux_folder2001 All Messages By This Member #143936 开云体育 I had one success and one failure. I have attached the failure. Tony ADoVC toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of Hans Summers via groups.io <hans.summers@...> Sent: Friday, April 25, 2025 2:36 PM To: [email protected] Notification <[email protected]> Subject: Re: [QRPLabs] #qmx SSB Firmware beta 1_01_005 release ? P.S. Tony please run 30m calibrarion and screenshot it at DAC 300 (or thereabouts) and again at it's completion or however far it gets.? 73 Hans G0UPL On Fri, Apr 25, 2025, 23:35 QRP Labs <hans.summers@...> wrote: Hi Tony 1 works, 2 works, but 3 ports results in no com ports. Ok that will be another thing for me to investigate then, considering that 3 worked for you in 1_01_004.? I'm keen to hear from Ludwig about Win7... 73 Hans G0UPL Screenshot 2025-04-25 144421.png Screenshot 2025-04-25 144453.png
mux_folder2001 All Messages By This Member #143937 开云体育 Here is the successful one. Tony AD0VC toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of mux_folder2001 via groups.io <canthony15@...> Sent: Friday, April 25, 2025 2:46 PM To: [email protected] <[email protected]> Subject: Re: [QRPLabs] #qmx SSB Firmware beta 1_01_005 release ? I had one success and one failure. I have attached the failure. Tony ADoVC From: [email protected] <[email protected]> on behalf of Hans Summers via groups.io <hans.summers@...> Sent: Friday, April 25, 2025 2:36 PM To: [email protected] Notification <[email protected]> Subject: Re: [QRPLabs] #qmx SSB Firmware beta 1_01_005 release ? P.S. Tony please run 30m calibrarion and screenshot it at DAC 300 (or thereabouts) and again at it's completion or however far it gets.? 73 Hans G0UPL On Fri, Apr 25, 2025, 23:35 QRP Labs <hans.summers@...> wrote: Hi Tony 1 works, 2 works, but 3 ports results in no com ports. Ok that will be another thing for me to investigate then, considering that 3 worked for you in 1_01_004.? I'm keen to hear from Ludwig about Win7... 73 Hans G0UPL Screenshot 2025-04-25 144056.png Screenshot 2025-04-25 144244.png
Stan Dye All Messages By This Member #143939 Serial port status with 1_01_006 on my Win10 home machine: - selecting 1 port works fine (presents as COM10) - selecting 2 ports work fine (present as COM10, COM12) - selecting 3 ports does not work: no COM ports appear.? In device manager, the USB Composite Device has this status: This device cannot start. (Code 10) {Operation Failed} The requested operation was unsuccessful. I couldn't see anything else in the driver events/messages that seemed useful. ? But on my system with 1_01_004, all 3 ports worked fine, presenting as COM10, COM11, COM12. The composite device started just fine. ? Stan KC7XE
Peter Jacobi All Messages By This Member #143943 Hi Hans, the new calib feature is working much better! Thank you! 1. My QMX+ on had problems on 80m on 004 => on 005 it's working completely. (I didn't try 160m) 2. My QMX 80-20m had only a few bands working on 004, the currently running calib process looks much better on 005. 3. My QMX 20-10m (with added 6m) is still problematic: ? ? ? ? ?Only 12m is looking good in all 3 calib steps. ? Although the hardware of all devices is similar, the results are quite different. ? My Questions: Do we have a top list of components with the greatest influence on the calibration process? Maybe, it's not only the transmitter, but also the receiver? Are there components, the builder can influence? ? Serial ports: On Linux the serial ports are working fine, but for the first time I recognized that the modem manager was active. It didn't interfere on 003 or earlier. The hints in the manual worked. ? PS: I had fun with the high band QMX on Madeira.? It was very easy to work several PY stations in CW on 10m! For CW 003 is working very nicely. ? 73 Peter DL4PJ ?

Previous Topic Next Topic