开云体育

QMX VFO

Don DeGregori All Messages By This Member #130738 Is this true? If I enable Rx Outside Band and put WWV in VFO A or B in a preset, it overwrites both A?and B with WWV. Any frequency within the ham band, it overwrites just A?or B. ? Don ? ? ?
Don DeGregori All Messages By This Member #130758 More ... ? It seems if I enable Rx Outside Band, it works. But from then on both VFO's get messed with.? What was in VFO A or B may change upon Power Down. After power up, I may see a different a frequency in either VFO. Example: Factory Reset Both VFO's have 14.074.00 in them Enable Rx out of band No change in VFO's Now I put 15.000.00 in VFO A I leave VFO B alone I do Shut down Wait 10 seconds Do QMX Start up Now notice VFO A and B both show 14.074.00 Same result using VFO B ? ? ? ?
Hans Summers All Messages By This Member #130831 Hello Don I'm struggling to reproduce any issues that you stated.? Firstly yes, RX out of band must be enabled. Because 15 MHz is out of band. Any attempt to load a 15 MHz frequency preset into the VFO will be ignored unless RX Out of band is enabled.? Loading presets loads into the currently selected VFO; which is either VFO A, or B, or when in Split mode, it is? loaded into VFO A. It doesn't load the preset into both VFO A and VFO B at the same time.? When I switched on and off, everything came back as I had left it before shutting down. No VFO's?were messed with.? Note 1: "shut down" means pressing and holding the volume knob. It is at THIS point that the radio state is saved. If you power down using the switch on your power supply, the microcontroller doesn't know your intentions and doesn't save radio state.? Note 2: 15 MHz by the default Band Configuration table set up, is in the 17m band not 20m band.? 73 Hans G0UPL toggle quoted message Show quoted text On Wed, Oct 2, 2024 at 4:04?AM Don DeGregori via <ddegreg1=[email protected]> wrote: More ... ? It seems if I enable Rx Outside Band, it works. But from then on both VFO's get messed with.? What was in VFO A or B may change upon Power Down. After power up, I may see a different a frequency in either VFO. Example: Factory Reset Both VFO's have 14.074.00 in them Enable Rx out of band No change in VFO's Now I put 15.000.00 in VFO A I leave VFO B alone I do Shut down Wait 10 seconds Do QMX Start up Now notice VFO A and B both show 14.074.00 Same result using VFO B ? ? ? ?
Don DeGregori All Messages By This Member #130862 Hello Hans, ? ? Note 2: 15 MHz by the default Band Configuration table set up, is in the 17m band not 20m band.? ? I didn't know that. I'll try it. ? Thanks ?
Don DeGregori All Messages By This Member #130879 Hans ... Setting WWV at 15.00.00 in the 17 meter band did the trick. Did I miss an instruction in the manual saying what you said? If I wanted use WWV at 10.000.00 instead, which band should I use? I know this WWV stuff is backburner, but I just wanted to find the trouble. Thank You Sir. ? Don
Hans Summers All Messages By This Member #130889 Hello Don If you log in with a terminal emulator, the band limits are defined in the Band Configuration screen. When you set a frequency by CAT or by selecting a Preset, this table is what's used to determine what band to use. And you can change it if you wish.? 73 Hans G0UPL toggle quoted message Show quoted text On Fri, Oct 4, 2024 at 7:48?AM Don DeGregori via <ddegreg1=[email protected]> wrote: Hans ... Setting WWV at 15.00.00 in the 17 meter band did the trick. Did I miss an instruction in the manual saying what you said? If I wanted use WWV at 10.000.00 instead, which band should I use? I know this WWV stuff is backburner, but I just wanted to find the trouble. Thank You Sir. ? Don

Previous Topic Next Topic