开云体育

JRC JST-245 connection to AC

chvjillson All Messages By This Member #63406 Good morning: ? I have a JRC JST-245 that I'd like to connect AC to ... has anybody had any luck doing so?? ? I do have a copy of the manual which does include a description of control commands but I'm not able to figure it out myself. ? Thanks! ? Clark KB9SJD
chvjillson All Messages By This Member #63423 Good morning everybody? .... an update to my request to see if AC can connect to a JST-245. ? Looking over the 245's manual and using PuTTY with serial settings set at 4800 baud, 8 data bits, no parity, 1 stop bit, no flow I was able to get a reply from the radio ..."I" followed by enter gets me a reply of I102143000020? ? I=header code 1=antenna in use (1) 0=bandwidth (wide) 2=mode (USB) 14300002 (hertz) 0=AGC (Slow) ? In AC Log, if I was to select Other for a rig, set baud to 4800 and other info exactly as I have it in PuTTY, and enter I for frequency command, I get nothing.? However when I enter 49 0D for a frequency command, I do get a reading but it shows up in the "unprocessed data return" window as I102143000020 ? Is there a way AC can parse that data string so that it only reads the frequency??? ? Thanks!
Scott Davis All Messages By This Member #63424 Hi Clark, Thanks for your e-mail.? There isn't a way to code the Other selection to perform all the associated rig interface functions.? It is only designed for testing sending commands to a rig, as you are doing now. Each selection is hard coded individually for each rig protocol. We are unfamiliar with the equipment you mentioned.? If the interface protocols match one of the existing rigs listed here, you should be able to use it with our software. We don't have access to the rig you mentioned.? It is very difficult to code rig interface for equipment that we can't actually attach to our development environment and we are knee deep in other aspects of the logging software at this point, so we aren't planning on circling back to rig interface coding at this time. I'm sorry that we didn't have the answer you were hoping for. Enjoy! 73, Scott N3FJP 开云体育 the Amateur Radio community with contesting and general logging software since 1997. 1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give . But do this with gentleness and respect... On Friday, December 6, 2024 at 10:16:47 AM EST, chvjillson via groups.io <chvjillson@...> wrote: Good morning everybody? .... an update to my request to see if AC can connect to a JST-245. ? Looking over the 245's manual and using PuTTY with serial settings set at 4800 baud, 8 data bits, no parity, 1 stop bit, no flow I was able to get a reply from the radio ..."I" followed by enter gets me a reply of I102143000020? ? I=header code 1=antenna in use (1) 0=bandwidth (wide) 2=mode (USB) 14300002 (hertz) 0=AGC (Slow) ? In AC Log, if I was to select Other for a rig, set baud to 4800 and other info exactly as I have it in PuTTY, and enter I for frequency command, I get nothing.? However when I enter 49 0D for a frequency command, I do get a reading but it shows up in the "unprocessed data return" window as I102143000020 ? Is there a way AC can parse that data string so that it only reads the frequency??? ? Thanks!
Jon Titus All Messages By This Member #63425 A suggestion:? Spell out equipment names: i.e: ?JRC JST-245 as Japan Radio Company, JST-245 transceiver. ? -- Jon Titus, KZ1G Herriman, UT
Mike Olbrisch All Messages By This Member #63426 开云体育 The solution is easy.? For me at least.? I try to be explicit when asking for help.? I try to be very explicit when offering help.? But not everyone is.? When I see a question that doesn’t make any sense to me, I often just hit DELETE and move on.? When I see a reply, and so much of the previous message was removed that I can’t figure out what the message began as, I hit DELETE and move on. Is there any one of us that doesn’t think their time is valuable?? You are making a withdrawal every day.? And you don’t even know your balance.? One day you wake up overdrawn. ? Vy73 - Mike - KD5KC. El Paso, Texas - DM61rt. SOTA W5T-Texas Association Manager. ? ? ? ? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of Jon Titus via groups.io Sent: Saturday, December 7, 2024 20:02 PM To: [email protected] Subject: Re: [N3FJPSoftwareUsers] JRC JST-245 connection to AC ? A suggestion:? Spell out equipment names: i.e: ?JRC JST-245 as Japan Radio Company, JST-245 transceiver. ? -- Jon Titus, KZ1G Herriman, UT

Previous Topic Next Topic