?

The CypCut software is what mine had on it. Mine is only a 1 KW but it works for testing. It is a 5' X 10' so it is using a bunch of my shop :) . My goal is not to make something "better" than the CypCut software. I want to make software that can do anything with the lasers. The software they have is fine for cutting plate but if you need to do some fancy stuff it falls apart quickly. The capacitance height control is working now, it is just talking to the power supply that is the issue and I seem to have a contact that can get me some data! I hope to be making parts again next month.

?

?

______________________________

?

Brian Barker

Engineering / Development

ArtSoft | Newfangled Solutions

Livermore Falls, Maine (USA)

Webpage: 

Ok, it is running CypCut which has some nice features but I’d rather run Mach4!

?

Thank-you!

Brian Martin

?

From: [email protected] <[email protected]> On Behalf Of Brian Barker
Sent: Tuesday, February 22, 2022 4:15 PM
To: [email protected]
Subject: Re: [MachCNC] Mach4 teach/record

?

That is using step and direction if it is running the Chinese control software. I took that all out of my laser and have been putting in Mach4 with Ethercat :) . We are working on trying to talk to the Raycus fiber generator now ... That is NO fun to try and get support from them

______________________________

?

Brian Barker

Engineering / Development

ArtSoft | Newfangled Solutions

Livermore Falls, Maine (USA)

?

Webpage: 

On 2/22/2022 2:21 PM, Brian Martin wrote:

That mostly makes sense, I have a Senfeng 4KW laser that has a mixture Yaskawa and Delt drives on it. I will do some more reading on Ethercat.

?

Thank-you!

Brian Martin

?

From: [email protected] <[email protected]> On Behalf Of Brian Barker
Sent: Tuesday, February 22, 2022 11:06 AM
To: [email protected]
Subject: Re: [MachCNC] Mach4 teach/record

?

Hi Guys,

EtherCat is basically a distributed motion controller. So picture an ESS that? is in the drives as well as in the IO blocks . Its sort of like a Modbus setup but is all in realtime. You can mix and match hardware in an Ethercat system. So you can have drives from Yaskawa , Elmo, Omron , Delta , Leadshine and so on all on the same network. The drives could power Steppers or servos (the system has no idea what one it is..) You can also use IO from in the drives OR add IO modules as well. The Ethernet cable just goes from drive to drive and IO to IO. With the Kingstar / Mahc4 setup you can also to ABS encoders so you do not need to home the machine when you start it. This is REALLY cools because you don't need to have home switches or any of that other hardware. You can also read as much data about the drive as you would like. So you can see what current the motor is using for example .

?

Now you can do this without the Kingstar software and add a hardware master like the board Vital systems has. This is a little more limiting but is much more flexible as to what PC it will work with. This is not the be all end all but it is the best way to make a high end system. It is the future... Well it really is here and the prices have been dropping like crazy.

?

Okay I think that made more confusion than it helped ;)

?

Thanks

Brian

?

?

______________________________

?

Brian Barker

Engineering / Development

ArtSoft | Newfangled Solutions

Livermore Falls, Maine (USA)

Webpage: 

On 2/22/2022 10:11 AM, o1bigtenor wrote:

?

?

On Tue, Feb 22, 2022 at 7:02 AM Brian Martin <bmm@...> wrote:

No problem, o1bigtenor. I want to know more about Ethercat also. Go ahead with the discussion!

Does an Ethercat drive network directly to the PC, or is there still a motion control interface/card?

?

Greetings

?

My phrase is 'what I know I can write on paper with big block letters and there is still plenty of room?

inside the thimble, after inserting the paper, for my finger' - - - - which is to say - - precious little.?

?

AIUI its a ethernet modification - - - to speed communications between devices, specifically?

- - again, AIUI, for drives to controls. There is a master info source at:?

?

?

my search engine (duckduckgo) included this with that address:?

?

The?EtherCAT?technology overcomes the system limitations of other Ethernet solutions: The Ethernet packet is no longer received, then interpreted and copied as process data at every connection. Instead, the Ethernet frame is processed on the fly.

?

So - - - it would seem that the value is in high speed connections.?

?

I'm not sure at what level ethercat comes into its own - - - haven't been able to?

find anything like 'a noobs guide to ethercat' . As usual one is expected to be?

at least sorta of a master form the get go - - - - docs are so tedious to write?

is what needs to be remembered (NOT - - -imo!). So the whole seems like it?

could be useful - - - but exactly how - - - well - - - that's why I was asking for?

info tips.?

?

(One more technology to master)

?

From the still quite befogged mind of?

?

(LOL)

?

?