开云体育

Is it possible to connect SBIG ST-8XE? directly to outside port of the box? Gemini 1 throuht a cable din 4 pin or 5 pin? The inside power of the camera has 5 pins, the outside port of the Gemini has

JoAnn, Hi. There is a nice video on using Arduino to control a dc motor+encoder. Since you don't need acceleration and position control all you need is to control speed that makes it pretty simple to

update: I have found an original stepper motor from a group member. Thanks!

Hi Ron. I think you have the concepts. Another useful thing is: you can work on testing this in the daytime. Keep your scope and finder scopes optics fronts covered up so the sunlight won't overheat

I am getting reliable meridian flips with my Titan and Gemini 2.? I use Maxim DL, but with ACP.? ACP is controlling the flip in my case.? I have never tried imaging with Maxim stand alone, so can't

Hi Michael This is exactly the flow I thought that I needed to take thanks so much for confirming: Power up gemini.net first then power up Gemini2 in horizontal parked position , Unpark , goto, align

Hi Ron For DSO targets like you showed (and wow, that is a demanding focal length) it would be easier than that: - cold start from CWD each night - press "start sequence" from SGP - go to bed :) i

Ah yes Now Im Starting to understand the utility of SGP and NINA which I have not seriously imaged with as SharpCap is so easy, hard to stop Yes, my setup is fixed So are you saying that from my

Hi Ron Yes, unless (or until?) you move to more sophisticated DSO type software (think sequence generator pro, NINA, etc.) plate solve probably won't help you with your gotos Are you tearing down and

HI Brian That doesn’t sound very easy Hutech IDAS LPF Imaging live stacking via SharpCapPro Ive not yet seen the utility of plate solving … Im waiting for such insight from my gurus Prime focus 10

Hi Ron, Of your options, #1 will surely work...but not what you want ideally. Your #2 option is wrong...here's how you should be doing that: Do start at CWD from Cold Bout and align, build your model

Hi Ron Can you describe your imaging setup? The easiest to do is cold start and plate solve every night. It depends on your setup. [email protected]> wrote:

Wow guys thanks so much for your attention so again i’m using a Gemini 2 my goal is to keep the model And go directly to the target In Easiest Manner with as less start up procedures possible I was

I have the same problem with my G11S.? You did not mention if your worm gears are spring loaded.? Mine are not, so anything I write applies just to regular worms.? The G11S comes without a goto

Hi Arun,! In the Gemini-1, a Cold Boot erases the entire set of Model parameters. Gemini.net shows all zeroes on the Advanced panel. The Genini-1 assumed the mount is polar aligned. Then you do a

Michael - To the point about Cold Boot (which I assume means no pre existing model) - does it matter whether the CWD position is dead on or not? In theory, assuming that the mount is accurately polar

Ok. Good to know. If you did a Cold Boot then ...it seems the -1 and -2 must be different in operation from a cold boot. That means the G-2 believes the CWD position was dead on, whereas the G-1 does

area. You will find they remain all zero value after the first Align to Bright star is done. I just did this using the hand controller and Gemini II definitely updates HA and DEC Index errors to

Hi Brian, Look at the Model settings in Gemini.net, using the Advanced panel Model area. You will find they remain all zero value after the first Align to Bright star is done. Therefore it is a Synch.

setting from zero value. That first Alignment only sets the encoder positions to the Gemini...really it is doing a Synch. Michael - is that how it works on Gemini I? i just tested this on Gemini II