Re: Best Way To Raise GM811G Saddle Height?
Hi John - I am looking for a DEC extension.
By
Jim Waters <jimwaters@...>
·
#70528
·
|
Re: Best Way To Raise GM811G Saddle Height?
Jim, Not sure if you are just talking about an RA extension. I pulled these pieces out of my G11 when I put in the break-apart RA EXT kit. I am sure HGM still sells these. They are 4 7/8 in. in
By
John Kmetz
·
#70527
·
Edited
|
Re: Used GM-8 Guiding Help
Hi Brian, Yea that's how I view the logs, tonight started clear but after an hour or so I would get an occasional cloud drifting through the FOV. A clearer night would be nice but it still seems like
By
Nick
·
#70526
·
|
Re: Used GM-8 Guiding Help
Nick just curious have you looked at these logs in PHD Log Viewer? they are pretty crazy, and shows a lot of lost guidestar problems and poor guidestar SNR
By
Brian Valente
·
#70525
·
|
Re: Used GM-8 Guiding Help
Update So I went ahead with the changes - enlarged the gearbox holes and aligned the shafts very well, worked with a much better polar alignment, adjusted worms to be on the looser side, they could
By
Nick
·
#70524
·
|
Re: Guiding without Gemini
Liam, Keep in mind that G11 is the easiest mount for OnStep conversion. GM8 is a little more complex, but also not hard. Look for reverse worm design for GM8 on onstep forum, it seems to be the
By
Alexander Varakin
·
#70523
·
|
Re: Help with interpreting PHD2 log on G11
Magnus, One possible source of the problem may be that your eastward weight bias is insufficient and your RA gears may be "floating" in a wind breeze or gust. I personally have found that the best way
By
John Nassr
·
#70522
·
|
Re: Typical Guided Performance of GM8G, GM811G, and G11
Liam, I have both G11 and GM8. I use G11 with 10" RC @2000mm FL in my home observatory and it is great. On the other hand, I bought GM8 specifically for travel imaging due to its lower weight. I tried
By
Alexander Varakin
·
#70521
·
|
Re: Help with interpreting PHD2 log on G11
Looks like you took this graph with PEC enabled and I don't think you will be seeing the expected frequencies in that case. Can you share the freq analysis without PEC and guiding?
By
Alexander Varakin
·
#70520
·
|
Re: Best Way To Raise GM811G Saddle Height?
That's the issue.? My 1/4-20 Cap Screws are?hardened steel and my hacksaw can't get through it.
By
Jim Waters <jimwaters@...>
·
#70519
·
|
Re: Best Way To Raise GM811G Saddle Height?
If it's just a matter of the bolt lengths, just get longer stainless steel 1/4-20 bolts...(at least that's the threads on my GM8 DEC). If the bolts are too long, you cut them to the correct length
By
Michael Herman
·
#70518
·
|
Best Way To Raise GM811G Saddle Height?
What¡¯s the best way to raise the height of my ADM Dovetail Saddle? I would like more clearance between the saddle and the motors. I am currently using a 3¡± round 1/2" thick aluminum stock but the
By
Jim Waters <jimwaters@...>
·
#70517
·
|
Re: Used GM-8 Guiding Help
I have lots of thoughts about your PHD2 settings.. Derek _____ Sent: Sunday, February 28, 2021 7:59 PM To: [email protected] Subject: Re: [Losmandy_users_io] Used GM-8 Guiding Help Update So I
By
Derek C Breit
·
#70516
·
|
Re: Used GM-8 Guiding Help
All good ideas. The puzzle is this report: The worm blocks are loose and the worm must be loose. But the axis is sticking or the worm is sticking? This is a used mount, right? Maybe it's needle
By
Michael Herman
·
#70515
·
|
Help with interpreting PHD2 log on G11
Hi! I've recently upgraded my C8 to a C11, and accordingly, things started becoming problematic after that....? particularly my guiding. I have an older G11, with OPW on the RA axis. I normally have
By
Magnus Larsson
·
#70514
·
|
Re: Used GM-8 Guiding Help
I suggest you err on the side of looseness with the RA. at least you can rule out stiction then
By
Brian Valente
·
#70513
·
|
Re: Used GM-8 Guiding Help
Thanks Brian, The DEC was an odd adjustment this go around for some reason, even with the block pushed as far away as possible the worm seemed tighter than normal, but still rotated without much
By
Nick
·
#70512
·
|
Re: Losmandy Polar scope calibration
These
By
George Cushing
·
#70511
·
|
Re: G11 Drive Gear Removal
Sorry to read that. I had the same experience in one G11 tucked motor system, and I gave up trying to get one of the gears off. I suggest you contact the factory for their guidance on this problem.
By
Michael Herman
·
#70510
·
|
Re: G11 Drive Gear Removal
Michael, Looking at these set screws under high magnification, it does seem they are stripped internally and are no longer a perfect hex shape. I don't see a way to easily remove the gears without
By
John Kmetz
·
#70509
·
Edited
|