开云体育

Huh you are correct, I don't see the G8 Dec listed separately like the TRA-Axis (RA Titan). But I've seen videos/screenshots with Scott and the G8 DEC if I recall, so I bet just a phone call and they

That would be a great product for Losmandy to offer - a Titan RA axis with GM8 Dec axis. Perfect for existing G11 owners playing mix-and-match ?

Cool thx. If I go with the TRA-Axis (Titan RA) then I might pickup a smaller G8 DEC to pop on the G11 RA and use that combo for imaging and the larger TRA-Axis + G11 DEC for the side-by-side viewing.

Yes that's correct That ends up being a G11T mount. I interchange my DEC with my G11T and my G11 I just wanted to make sure you didn't end up buying a full Titan, which comes with the Titan Dec! Brian

Thx Brian - I actually have the G11 DEC and RA in the split axis model - so it was something like G11GFT with the RAEXK axis adapters - My understanding is I can just plug the Titan RA with the RAEXK

Thank you all - Yes, I saw the Titan group - but it had a pretty small membership so thought I'd post more broadly here as I think my questions are more around the impact of side-by-side for visual.

just to clarify a "Titan RA" with G11 DEC is a G11T you can't actually use *the* Titan RA with the G11 DEC Brian wrote: -- Brian Brian Valente portfolio brianvalentephotography.com

There is a Titan IO group as well. ?Not a lot of traffic but some well experienced folk there. ?Though they usually visit these forums as well. /g/Titan-mount/topics That’s a lot

?Hi Charles, I can only comment on the side-by-side balancing. With the Losmandy side-by-side plate (which works well for me) you turn the mount's saddle sideways to accept the side-by-side

Hi Charles The Titan RA you'll want is the G11T i have one and use it with my AT12RC f8 scope. the total payload for me is about 70lb, works great. I haven't had any issues with DEC. i do have about

Hello - new to forum. I have a G11 with split axis currently, use it primarily for imaging. I'm considering a heavier payload for visual observing, a side-by-side setup with and Edge14hd and an AP

Yep thanks Greg check the data sheet for MIC5801YN (22pin ver Pdip) see here https://au.mouser.com/ProductDetail/Microchip-Technology-Micrel/MIC5801YN?qs=kh6iOki%2FeLERtazGLeUNFQ%3D%3D check pulses

Thanks for the suggestions.? I have tried plugging it into the RA socket and the Dec motor does turn.? I have also opened the case and looked for any obvious weak solder joints, burnt spots, or

First thing I'd do is pull the ?processor inspect the pins for corrosion and reinsert it.? Any contact cleaner?can be deal with corrosion. I've used WD-40 and a q-tip.

Greg, The first two things to check are the handbox and the sockets (6p6c modular phone receptacle) on the PCB, esp. the one for the DEC drive - you seem to have eliminated the cable and the motor

I agree that the existing cables are a minimum length and they have frictional insulation that can grab the metal surfaces. You also have a rare mount in the G11T, which has a more massive RA drive

Greg. Can you plug the Ra into the DEC .....and does this move? ?Probably not. The motors are bipolar types there is an IC MIC5801YN that drives the respective motor coils. ?I’m not at home atm

I have an old G-8 that's been sitting for a while, though it worked fine a few years back the last time I used it.? This is the non-goto version without a Gemini, just the stock computer and

If it helps, I believe the Dec cable is longer than the RA, so as a start you could order a replacement Dec cable from Losmandy and use that for your RA:

KJware its rare to see a bad motor cable but there are instances of: the motor socket has cracked solder joints ( causing many and varied motor drive issues); and the motor socket pins lose