开云体育

I've been using FT8, Winlink and all other digital modes quite successfully with that hardware combination and the following radio settings: 05-06: CAT RATE: 19200 05-08: CAT RTS: DISABLE 08-01: DATA

I connected a hard? Ethernet cable wire after this happened to get a screen shot.? ?I was using a USB keyboard and mouse and a HDMI monitor

It happened again.? Screen shot included.? Note the mispelled "lateest" word and note that I had no wifi connection at the time BAP ran.? It booted up that way and later picked up an IP address.?

Never thought about this, but a great idea! I bet hamlib would hold the answer. I wish I could look into this further but I’m nearly underwater doing a forensic audit. ??? Cant wait to see

You may have deleted your BAP directory. You can reinstall BAP with the following commands: *cd* *git clone https://github.com/km4ack/pi-build.git * -- 73, de KM4ACK YouTube (

If you have 3.0.8 installed there should be a shortcut in the menu under the ham radio section. If it isn't there, you can run the BAP update script from the command line with *~/pi-build/update * The

FLrig can be set to automatically turn the rig on and off (found in the FLrig extra controls under the Misc tab). It's a useful feature, but sometimes the apps I use don't utilize FLrig so there's no

Hello to the forum, I went the next steps in the configuration (after Flrig, JS8Call and WSJTX setup) to PAT. Made the configuration (incl. Port change to 5050) but in the terminal window I got the

When in to my PI's drop down menu clicked on preferences then build-a-pi Now I get the error message:? Invalid desktop entry file: */usr/share/applications/build-a-pi.desktop ???????? -- Thank you

About 3 months ago I installed (I thought it was) BAP and it had a GUI to select what apps to install.... 1.? I cannot find it on my PI to run it again (no icons in the click down main menu). 2. I

Hi alex, thanks ... I have a PI image from March and after put the image on the SD i made the usual updates on the system, so it should be the actual kernel. I installed the BAP from:

Jason, Thanks....I'll try the 891 menu settings part of the article. Ken KB4XT

I did a new Build-a-Pi and the N3DJS build. It worked immediately on fldigi, flrig, wsjtx. But the Build-a-Pi didn't work at all. I read about 7610 problems with flrig on the fldigi site. I'm going to

I got sidetracked on packet and tinkered with Winlink & vara with the PC. Cleaning shack I found my teensy pi tnc board. Question. Can I EASILY use it on my build-a-pi? Otherwise I'll find a use for

I followed this website for changes that needed to be made for digital work with the 891 https://kd9cjx.wordpress.com/2017/11/22/how-to-setup-the-yaesu-ft-891-to-fldigi/ -- 73, de KM4ACK YouTube (

Are you running the latest version of BAP? There was some issues with the FLSUITE in 3.0.7 that were documented here ( /g/KM4ACK-Pi/message/4538 ) -- 73, de KM4ACK YouTube (

Hi Erwin, Not sure what is happening in your situation, but during the last two days I have done about 6 times a fresh install of Build-a-Pi 3.0.8 without any issues on a Raspberry Pi 4 (4Gb). I used

Thanks again for a 100% system when i want to send a photo via pat mail. Does pat autosize photo? or must photo ve a certain size for using pat mail and ardop reason for question is that seems if we

Hi, after long time I have to be busy in my job I started a fresh installation on my RP4 with BAP - thanks Jason for this great possibility. All runs smooth but Flrig wasn‘t installed. Tried the

Thank you Jason for the command line work. ?The system is currently updating! tahe care, Sean