Re: Pat Winlink latest update
The post is from July 15.? I encountered yesterday the issue of not having the USGS DYFI template.? I updated to v.163 of forms successfully and yet nothing.? I went to my .wl2k/Standard_forms directory and saw the directory
for USGS there, but with missing single quotes.? I guess the single quotes are for directory names with spaces in between words.? The directory name was simply USGS, whereas the rest have the word forms attached.? I changed
the name to USGS forms but still nothing.? Any idea how to solve this?? I have not tested it using iceweasel.? I am using Chromium.
|
It wouldn't be terribly hard to make one out of a consumer BT adapter that uses a headphone/microphone jack (TRRS) by cutting off the jack and soldering in some wires to a mini din. You would have to use CAT control or VOX for PTT.?
That being said, I would be a little concerned a bit with the audio delay inherent in a lot of those devices. It might muck up the timing of some digital signals where timing is critical.?
As far as I know, one for Bluetooth audio doesn't exist for teh 817. I would be stoked if someone proved me wrong :-)
--
73, de KM4ACK
|
|
|
Re: Xiegu G90 Flrig 1.3.54
#flrig
I am available for the net
On 09/15/2021 9:53 AM davdj0nsn@... wrote:
Lee,
I'm having the same problem with flrig and the G90-XGG combo as Paul.? I tried that port selection you suggested and got this error message:
Select separate ports
Well, that's a pretty useless error message, I must say.
Has anyone come up with a solution to this issue, or is it still open?? I'm fast coming to the conclusion that the XGG interface and flrig are a bad combination.
|
From the "years ago" file, check out:
I don't know what is available today but it would be nice to recreate with parts available today.
Fred N7FMH
toggle quoted message
Show quoted text
-----Original Message----- From: [email protected] [mailto: [email protected]] On Behalf Of Marty Hartwell Sent: Tuesday, September 14, 2021 5:16 PM To: [email protected]Subject: [KM4ACK-Pi] Bluetooth adapter Hi Ok, we have blue tooth for CAT for the FT-817, has anyone seen one for the other interface, for audio? That would be so nice to have to get rid of some more cabling. Marty kd8bj -- This email has been checked for viruses by Avast antivirus software.
|
Re: Xiegu G90 Flrig 1.3.54
#flrig
Lee,
I'm having the same problem with flrig and the G90-XGG combo as Paul.? I tried that port selection you suggested and got this error message:
Select separate ports
Well, that's a pretty useless error message, I must say.
Has anyone come up with a solution to this issue, or is it still open?? I'm fast coming to the conclusion that the XGG interface and flrig are a bad combination.
|
Re: Timing for FT8 and other digital modes
Jim, if you are getting your GPS coordinates correctly then go to the ¡°time.is¡± website and it will tell you if your system clock is accurate. ?Assuming you have a working internet connection of course.
|
Pat Templates 163 - Stuck in reboot
Hello everyone,
So I updated the templates in Pat this morning in order to update the Severe Wx Template to get working. After the update I didn¡¯t see the template I Pat, so for giggles I decided to reboot my Pi4 (8GB). After not being able to connect to it via VNC after I thought plenty of time a lapsed, the VNC connection would time out. This happened several times. So I connected the Pi to my HDMI TV and it goes through its thing, but stops at the rainbow screen. It¡¯s been sitting there for a long long long while.
I¡¯m wondering if the new Pat template update did something to my Pi since it has been working for weeks now with zero issues. I only go in to use Pat every few days and I disconnect from it. This update was the only thing I¡¯ve updated ?since BAP 3.1.0 came out.?
OR is this just a coincidence in timing???
Any ideas???
Thanks & 73.
Jeff K3JRZ ?#404
--
|
Re: IC 705 gpsd and FLRIG conflict.
Still don¡¯t have it posting Gridsquare to Conky
Did you use the GPS update tool and pick the one ending in "if02"? --
73, de KM4ACK
|
|
|
Re: Timing for FT8 and other digital modes
Your system should be pulling time from the GPS if you don't have an internet connection. --
73, de KM4ACK
|
|
|
As far as I know, one for Bluetooth audio doesn't exist for teh 817. I would be stoked if someone proved me wrong :-) --
73, de KM4ACK
|
|
|
Hi
Ok, we have blue tooth for CAT for the FT-817, has anyone seen one for the
other interface, for audio? That would be so nice to have to get rid of some
more cabling.
Marty kd8bj
|
Timing for FT8 and other digital modes
I have Build a Pi running on a Pi4. I have a GPS receiver taped to a basement window and Conky is displaying my gridsquare.
?
Is there anything else I need to do for FT8 timing? I assume that if gridsquare is showing in Conky, the pi is getting it¡¯s time from the GPS receiver.
?
Thanks in advance for your suggestions.
Jim, W0RLD
?
Sent from for Windows
?
|
Re: IC 705 gpsd and FLRIG conflict.
That got it thanks. All working together. Still don¡¯t have it posting Gridsquare to Conky but I just can run cgps command and it¡¯s available.? Enjoying the Build a Pi ?and learning! Thanks again, Paul?
toggle quoted message
Show quoted text
On Sep 12, 2021, at 7:31 AM, km4ack <jason.oleham@...> wrote:
?
Hi,
I¡¯m new to the raspberry 4 and build a pi. I have most everything working bit grid square on Conky. The GPS works off the IC-705 only by itself, this was confirmed by gpsd check. If it¡¯s running I can¡¯t operate FLRIG or VNC. I have to turn off the 705 reboot raspberry then turn on 705 after the raspberry is on, then GPS no longer works and FLRIG and VNC operate fine.
this group has helped immensely getting up and running, Can someone point me in the right direction to solve this problem. Thanks!
By running: ls /dev/serial/by-id/you will find there are two listings for the 705 which are something similar to: usb-Icom_Inc._IC-705_IC-705_12007996-if00 usb-Icom_Inc._IC-705_IC-705_12007996-if02 The one that ends in "if00" is the one that should be used in FLRIG and the one that ends in "if02" should be used for the GPS connection. This will avoid the conflict. First use the GPS update tool and set the GPS to the one ending in "if02" and then configure FLRIG to use the other one and you should be good. --
73, de KM4ACK
|
|
|
I'm using the 2.0 ports due to the issue with the 3.0 I'm guessing the same thing I'll get another ordered and see if that changes anything? thank you for all the help?
73 (no ham license yet!)
|
Re: flrig setup with Kenwood TS-2000
Tom,
I bought the cable off of ebay. Please see the attached photo.
On Tue, Sep 14, 2021, 8:15 AM Tom Workman < k0tw@...> wrote: Fred, N7PN...
What cable are you using between the your Signalink USB and your TS-2000? Is my assumption correct that it connects to the COM port on TS-2000? Is the cable commercially available or did you build it?
Thanks again.
Tom - K0TW
|
Re: flrig setup with Kenwood TS-2000
Fred, N7PN...
What cable are you using between the your Signalink USB and your TS-2000? Is my assumption correct that it connects to the COM port on TS-2000? Is the cable commercially available or did you build it?
Thanks again.
Tom - K0TW
|
Since you says that you have never seen the blinking green light even when outside, there is certainly an issue with the GPS. Are you using a USB 3 device in one of the USB 3 ports on the Pi? This is know to create enough RFI to jam the GPS If you aren't using USB 3 and still can't get a lock while outside, it's possible that you have a defective GPS unit. --
73, de KM4ACK
|
|
|
Tested pat winlink this morning again and get a time out io error on black screen of pat mail screen I think a setting ??
All was working fine yesterday. I did a reboot too, but it stay same Freq written in blick and then red line through it. Qso error
Rigctl green Flrig green Ardop Green
Any suggestion where to look please? Greetings from the Namib
Pieter Jacobs De v51pj 73
toggle quoted message
Show quoted text
On 13 Sep 2021, at 21:49, ham123789 <ribet@...> wrote:
?On Mon, Sep 13, 2021 at 10:12 AM, ham123789 wrote:
rigctl -vvv -m 1 f
I solved the issue by re-installing Hamlib and now Fldigi, WSJT-x, JS8CALL and Pat applications all work using Flrig. I am assuming that something had gotten set wrong in the Hamlib config files and that a re-install corrected it Thanks, George AK4NG
|
Yes sir thats the one I have.?
|
Re: BAP 3.1 Patch screen multiple patches
I have a couple other patch tool ideas but don't have a github account, so will note them here - low priority, just ideas:
1. Check for existing successfully applied patches on a system and discontinue displaying them on the list in the update tool
2. Close the terminal window spawned by each patch once the patch is fully applied
3. Remove the test patch and then, if there are no non-applied patches for a given system, display a message like "You are up to date with all patches!"
|
Brian Dale
km4ack
Fred-N7PN
Tom Workman