Re: IC 705 gpsd and FLRIG conflict.
Hi,
I¡¯m new to the raspberry 4 and build a pi. I have most everything working bit grid square on Conky. The GPS works off the IC-705 only by itself, this was confirmed by gpsd check. If it¡¯s running I can¡¯t operate FLRIG or VNC. I have to turn off the 705 reboot raspberry then turn on 705 after the raspberry is on, then GPS no longer works and FLRIG and VNC operate fine.
this group has helped immensely getting up and running, Can someone point me in the right direction to solve this problem. Thanks!
By running: ls /dev/serial/by-id/you will find there are two listings for the 705 which are something similar to: usb-Icom_Inc._IC-705_IC-705_12007996-if00 usb-Icom_Inc._IC-705_IC-705_12007996-if02 The one that ends in "if00" is the one that should be used in FLRIG and the one that ends in "if02" should be used for the GPS connection. This will avoid the conflict. First use the GPS update tool and set the GPS to the one ending in "if02" and then configure FLRIG to use the other one and you should be good. --
73, de KM4ACK
|
|
|
Re: FLAMP install not working from Build-a-Pi
I found a workaround, and have submitted it to Jason for his consideration.
?
Below is that suggestion:
Hi Jason -
?
Continued with the past problem in that FLAMP always
indicated 'NEED UPDATE', but never updated from
2.2.05 to 2.2.07.
?
A fix for this involved adding "| tail -1)" to the end of
the AMPTAR=$ line in the FLAMP section of the
'flsuite.funtion' script.
?
The update went smoothly, and now, with 2.2.07
installed, the FLAMP NEEDS UPDATE message
has disappeared.
?
Is this a valid 'fix'?
?
73 de Jerry - LU/K4OAM
Jerry, I received your email but it has been a couple of crazy days for me. I'll review the fix you submitted and see if I can get a new patch out in the next few days. --
73, de KM4ACK
|
|
|
Re: IC 705 gpsd and FLRIG conflict.
Hi Paul,
I've been out on a ham exercise all day and am exhausted.? I will
try tomorrow to see what I am doing that is different than you.?
For the moment, I can tell you the single USB cable connection is
running all three with my Pi(s); rig control, sound codecs, and
GPS all without any problems.? I guess I just lucked into it
because all I've done is follow the BAP instructions for this
marriage made in heaven, the IC-705 to the Raspberry Pi 3B+ and 4B
running headless with PC, tablet and phone control.? At the very
least I want you to know that it is being done.? Later!
73
Herm, W7HRM
On 9/11/2021 6:46 AM, Paul via
groups.io wrote:
toggle quoted message
Show quoted text
Hi,
I¡¯m new to the raspberry 4 and build a pi. I have most
everything working bit grid square on Conky. The GPS works off
the IC-705 only by itself, this was confirmed by gpsd check. If
it¡¯s running I can¡¯t operate FLRIG or VNC. I have to turn off
the 705 reboot raspberry then turn on 705 after the raspberry is
on, then GPS no longer works and FLRIG and VNC operate fine.
this group has helped immensely getting up and running, Can
someone point me in the right direction to solve this problem.
Thanks!
Paul WD8SCV
_._,_._,_
|
Re: FLAMP install not working from Build-a-Pi
Don't know what to tell you Bill, but it's working fine here under the latest Buster and Build-A-Pi 3.1.0
Jerry
Having sames issue so I went looking into why; Here's what I found :
looks like 2.2.07 is not available yet for PI os Buster (based on Debian Linux).
So until it's released to Buster we maybe in for a short wait..
Bill Harding
N3VMT
|
Re: FLAMP install not working from Build-a-Pi
Having sames issue so I went looking into why; Here's what I found :
looks like 2.2.07 is not available yet for PI os Buster (based on Debian Linux).
So until it's released to Buster we maybe in for a short wait..
Bill Harding
N3VMT
|
I have same problem here.? Only difference in setting is mine use 5000 instead of 8080
What i also noted is that rigcontrol in conkey does not go green -? In older version it used to go green but did not go red after closing down of pat winlink. Then i had to reboot pi otherwise other apps dont work as stand alone without flrig
Wsjt-x was not working but after installing the patch i cganged settings to another radio and then changed it back to correct radio and now it is working with new patch. Thanks for that solution Jason.? Greetings from the Namib
Pieter Jacobs De v51pj 73
toggle quoted message
Show quoted text
On 12 Sep 2021, at 00:38, ham123789 <ribet@...> wrote:
? [Edited Message Follows]
FLRIG works fine with FLDIGI and WSJT-x ARDOP and PAT does not change the radio frequency nor activate the PTT when I select "Action/Connect" on the PAT menu and then select an RMS from the list. The same happens if I use "Find WINLINK Gateways" This is a new build on a new RP 4B BAP v3.1.0 - all patches added FLRIG v1.4.2 Pat Menu v2.3 ARDOPC v1.0.4.1j Pat v0.11.0 PTT set to TRUE in Manage PAT/Set ARDOP PTT #Config file for Pat Menu #20200429 KM4ACK MYCALLSIGN=AK4NG MAP=usa RIGCONTROL=yes ARDOP="/home/pi/ardop/./piardopc 8515 plughw:2,0 plughw:2,0" ARDOPGUI="/home/pi/ardop/./piARDOP_GUI" DIREWOLF="direwolf -p" KISS="sudo /usr/sbin/kissattach /tmp/kisstnc" AXP=wl2k RIG="/usr/local/bin/rigctl -m 4" MODEHF=USB MODE2M=FM PORT=8080 LOG=/home/pi/Documents/mylog.txt AMRRON=no
|
FLRIG works fine with FLDIGI and WSJT-x
ARDOP and PAT does not change the radio frequency nor activate the PTT when
I select "Action/Connect" on the PAT menu and then select an RMS from the list.
The same happens if I use "Find WINLINK Gateways"
This is a new build on a new RP 4B
BAP v3.1.0 - all patches added
FLRIG v1.4.2
Pat Menu v2.3
ARDOPC v1.0.4.1j
Pat v0.11.0
PTT set to TRUE in Manage PAT/Set ARDOP PTT
#Config file for Pat Menu
#20200429 KM4ACK
MYCALLSIGN=AK4NG
MAP=usa
RIGCONTROL=yes
ARDOP="/home/pi/ardop/./piardopc 8515 plughw:2,0 plughw:2,0"
ARDOPGUI="/home/pi/ardop/./piARDOP_GUI"
DIREWOLF="direwolf -p"
KISS="sudo /usr/sbin/kissattach /tmp/kisstnc"
AXP=wl2k
RIG="/usr/local/bin/rigctl -m 4"
MODEHF=USB
MODE2M=FM
PORT=8080
LOG=/home/pi/Documents/mylog.txt
AMRRON=no
|
You could try to turn it on manually from the raspi-config menu using the command
sudo raspi-config
I know you can setup your wifi options in that menu.
Can you see the wifi icon on your desktop?
Trevor KJ7MLK
On Sat, Sep 11, 2021, 8:19 AM Loyd < ne4lh1@...> wrote: I'm trying to install build-a-pi on my raspberry pi 4 8gb, install the program go thru the setup script after the reboot i can not connect to internet.
i can not access my wifi or ethernet get "no wifi installed" when i try to connect to wifi.
I tried 3 time yesterday from a new image.each time.
any suggestions
|
Re: FLAMP install not working from Build-a-Pi
I found a workaround, and have submitted it to Jason for his consideration.
Below is that suggestion: Hi Jason -
Continued with the past problem in that FLAMP always indicated 'NEED UPDATE', but never updated from 2.2.05 to 2.2.07.
A fix for this involved adding "| tail -1)" to the end of the AMPTAR=$ line in the FLAMP section of the 'flsuite.funtion' script.
The update went smoothly, and now, with 2.2.07 installed, the FLAMP NEEDS UPDATE message has disappeared.
Is this a valid 'fix'?
73 de Jerry - LU/K4OAM
Updated to the new 3.1.0 and applied the FLMSG patch successfully. I was hoping that it would fix whatever was wrong with the error when triyng to update FLMSG also. This is the output I get in the terminal after trying to update:
--2021-09-11 09:53:26--?
Resolving ()... 143.95.246.118
Connecting to ()|143.95.246.118|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 518387 (506K) [application/x-gzip]
Saving to: \u2018flamp-2.2.05.tar.gz\u2019
?
flamp-2.2.05.tar.gz 100%[===================>] 506.24K? ?320KB/s? ? in 1.6s? ??
?
2021-09-11 09:53:28 (320 KB/s) - \u2018flamp-2.2.05.tar.gz\u2019 saved [518387/518387]
?
--2021-09-11 09:53:28--?
Resolving flamp-2.2.07.tar.gz (flamp-2.2.07.tar.gz)... failed: Name or service not known.
wget: unable to resolve host address \u2018flamp-2.2.07.tar.gz\u2019
FINISHED --2021-09-11 09:53:28--
Total wall clock time: 2.4s
Downloaded: 1 files, 506K in 1.6s (320 KB/s)
tar: flamp-2.2.07.tar.gz: Not found in archive
tar: Exiting with failure status due to previous errors
/home/pi/pi-build/functions/flsuite.function: line 154: cd: too many arguments
menu mods already made
Revision 20210411 installed
Any suggestions or wait for another patch?
|
BAP 3.1 Patch screen multiple patches
I started to play around with the new patch feature with BAP 3.1
I did find that if you selected multiple patches, it only installs the first patch. The other patches are not installed, so I had to install them one at a time.
No big deal on doing the patches one at a time (at least for me), but I did expect to install multiple patches when I am able to select multiple patches.
But the patch update works like a champ.
|
I'm trying to install build-a-pi on my raspberry pi 4 8gb, install the program go thru the setup script after the reboot i can not connect to internet.
i can not access my wifi or ethernet get "no wifi installed" when i try to connect to wifi.
I tried 3 time yesterday from a new image.each time.
any suggestions
|
IC 705 gpsd and FLRIG conflict.
Hi,
I¡¯m new to the raspberry 4 and build a pi. I have most everything working bit grid square on Conky. The GPS works off the IC-705 only by itself, this was confirmed by gpsd check. If it¡¯s running I can¡¯t operate FLRIG or VNC. I have to turn off the 705 reboot raspberry then turn on 705 after the raspberry is on, then GPS no longer works and FLRIG and VNC operate fine.
this group has helped immensely getting up and running, Can someone point me in the right direction to solve this problem. Thanks!
Paul WD8SCV?
|
Re: Dire Wolf Problem "Could not open audio device plughw:2,0 for input
#antenna
I just ran command "arecord -l" and it didn't list anything. Then it hit me to plug a device in, so I grabbed a pair of USB headsets and re-ran that command and now it shows it. I'm building this Pi on the desk and I don't have the radio ready and plugged in. I have to figure out how I want to interface the Alinco DR-135 Mk II.?
|
Re: How to Resume a Failed Install
Hi Steve
Check the pi for what you wanted to install to make sure all
finished. I saw where mine finished
but Fldigi wasn't and maybe some others didn't install.
Just to be sure.
Marty
On 9/11/21 9:12 AM, Steve Sutterer
wrote:
toggle quoted message
Show quoted text
Marty,
Thanks for your reply. It finally completed the build. Nearly 30
hours!?
73,?
Steve
|
Re: How to Resume a Failed Install
Marty,
Thanks for your reply. It finally completed the build. Nearly 18 hours!?
73,?
Steve
|
Re: How to Resume a Failed Install
Hi Steve
I think with the Pi3 you have run into the run out of swap space
issue. On Pi's with both 3 and 4 with
4GB or less or maybe it is less than 4GB of RAM you will see this
behavior when installing Fldigi
and maybe some other memory intensive compiles. A search for
increasing swap space on Rpi
will get the way to increase swap space on your pi to allow it to
complete the BAP install.
Hope this helps and sorry I don't have the procedure to copy to
just send you.
Marty kd8bj
On 9/10/21 8:47 PM, Steve Sutterer
wrote:
toggle quoted message
Show quoted text
Over 8 hrs into this now, still blank screen.
I would like to get this running before we head to Alaska on
Wednesday, simply for FT8 (WSJT-X). Should I just omit the other
packages and try another pass at this? I would be running headless
with a wifi-only iPad Air, so I probably need the GPS dongle
support as well.
Or am I better off to just skip BAP and do a manual install of
WSJT-X and the GPS support?
Or should I just be patient and let this run?? ?:-)
Thanks
Steve AK0M
|
FLAMP install not working from Build-a-Pi
Updated to the new 3.1.0 and applied the FLMSG patch successfully. I was hoping that it would fix whatever was wrong with the error when triyng to update FLMSG also. This is the output I get in the terminal after trying to update:
--2021-09-11 09:53:26--? http://www.w1hkj.com/files/flamp/flamp-2.2.05.tar.gz
Resolving www.w1hkj.com (www.w1hkj.com)... 143.95.246.118
Connecting to www.w1hkj.com (www.w1hkj.com)|143.95.246.118|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 518387 (506K) [application/x-gzip]
Saving to: \u2018flamp-2.2.05.tar.gz\u2019
?
flamp-2.2.05.tar.gz 100%[===================>] 506.24K? ?320KB/s? ? in 1.6s? ??
?
2021-09-11 09:53:28 (320 KB/s) - \u2018flamp-2.2.05.tar.gz\u2019 saved [518387/518387]
?
--2021-09-11 09:53:28--? http://flamp-2.2.07.tar.gz/
Resolving flamp-2.2.07.tar.gz (flamp-2.2.07.tar.gz)... failed: Name or service not known.
wget: unable to resolve host address \u2018flamp-2.2.07.tar.gz\u2019
FINISHED --2021-09-11 09:53:28--
Total wall clock time: 2.4s
Downloaded: 1 files, 506K in 1.6s (320 KB/s)
tar: flamp-2.2.07.tar.gz: Not found in archive
tar: Exiting with failure status due to previous errors
/home/pi/pi-build/functions/flsuite.function: line 154: cd: too many arguments
menu mods already made
Revision 20210411 installed
Any suggestions or wait for another patch?
|
Re: Dire Wolf Problem "Could not open audio device plughw:2,0 for input
#antenna
Run this command: arecord -land it should return something like this **** List of CAPTURE Hardware Devices **** card 2: CODEC [USB Audio CODEC], device 0: USB Audio [USB Audio] ? Subdevices: 0/1 ? Subdevice #0: subdevice #0 In the example above the card is 2 and device 0 hence plughw:2,0. If your card is different, you will need to modify your direwolf.conf file to match the output of the output above. If you need to make a change the direwolf.conf file will be in your home directory and can be modified with a text editor. On line ~77 you should see "ADEVICE? plughw:2,0" Change the last two numbers on this line to match your card/device number. --
73, de KM4ACK
|
|
|
Re: Dire Wolf Problem "Could not open audio device plughw:2,0 for input
#antenna
I did not mean to add that #antenna and I can't see a way to delete it. Perhaps a Mod can pull that off.
|
Re: FLRIG loses connectivity with 891
Good information and I¡¯ll be checking my setup.?
Thanks
|
km4ack
Herm W7HRM
N3VMT
Loyd
Jason-K6FAK[HRTV]