|
Re: display
One of the values in the loop I had you add placed the display in the orientation you wanted. Take whatever that value is and ?? tft.setRotation( (uint8_t)
i); ?
place it where i is above. Erase all of the code I had you add, except the line above with the number instead of i. Save the file. Now recompile and upload the code and you're done. It should be a permanent part of the code. Jack, W8TEE
On Friday, April 5, 2019, 2:55:38 PM EDT, k7da <k7da@...> wrote:
now that there is a way to rotate the image on the display what
must i do to make this a permanent thing?? i am not a hacker so do
not know what to do with this information. dave? k7da
On 4/4/2019 8:09 PM, jjpurdum via
Groups.Io wrote:
Are you saying to see the main display page that looks like
this:
Jack, W8TEE
On Thursday, April 4, 2019, 6:51:30 PM EDT, k7da
<k7da@...> wrote:
it did compile and and it id upload? the code works
and now how do i use that info to effect the display
permanently? and i assume remove the provided code.? i
did not have the serial link hooked up but it looks
like value 3 is the one i want. dave k7da
On
4/1/2019 7:30 PM, jjpurdum via Groups.Io wrote:
If it compiled and uploaded and ran, that's
what's important. What happened on screen? Did it
say Upload Complete?
Jack, W8TEE
On Monday, April 1, 2019, 10:08:59 PM EDT,
k7da <k7da@...>
wrote:
?it complies now but there are some warnings that i can figure out how to copy. dave k7da
On
4/1/2019 6:38 PM, jjpurdum via Groups.Io
wrote:
I said go INTO the setup() function
and place the code. You didn't.
It should be:
void
setup() {
// a
bunch of statements....
// At the
very bottom of setup, BUT INSIDE IT
? for (int i = 0; i < 4; i++) {
?? tft.setRotation( (uint8_t)
i);
?? tft.setCursor(10, 10);
?? tft.print("New rotation value of
");
?? tft.print(i);
?? delay(5000);?????? // You have
5 seconds to view the message
? }
Jack, W8TEE
On Monday, April 1, 2019, 7:24:21 PM
EDT, k7da <k7da@...>
wrote:
i got an error as follows
Arduino: 1.8.8 (Windows 10), TD:
1.45, Board: "Teensy 3.6, Serial,
180 MHz, Faster, US English"
dave k7da
On
4/1/2019 5:58 AM, jjpurdum via
Groups.Io wrote:
I assume that you have a
graphics object named tft.
Go into the
setup() function and add this
code at the bottom:
for (int i = 0; i
< 4; i++) {
??
tft.setRotation( (uint8_t) i);
??
tft.setCursor(10, 10);
?? tft.print("New
rotation value of ");
?? tft.print(i);
??
delay(5000);?????? // You have
5 seconds to view the message
}
and see if any of the
rotation values works for what
you need.
Jack, W8TEE
On Sunday, March 31, 2019,
11:26:30 PM EDT, k7da <k7da@...>
wrote:
i mounted the display upside down and turning it over makes it not fit the hole. so i need to turn the picture upside down. is that possible in sofeward or alectrically? dave k7da
On
3/31/2019 7:57 PM,
jjpurdum via Groups.Io
wrote:
What do you mean
"turned over"? There's
a Landscape and
Portrait mode
Jack, W8TEE
On Sunday, March
31, 2019, 10:29:40
PM EDT, k7da <k7da@...>
wrote:
can
the display be
turned over in
software?
dave
k7da
|
|
Re: display
Then it's working? If so...good on ya!!! Jack, W8TEE
On Thursday, April 4, 2019, 11:44:02 PM EDT, k7da <k7da@...> wrote:
YES On 4/4/2019 8:09 PM, jjpurdum via
Groups.Io wrote:
Are you saying to see the main display page that looks like
this:
Jack, W8TEE
On Thursday, April 4, 2019, 6:51:30 PM EDT, k7da
<k7da@...> wrote:
it did compile and and it id upload? the code works
and now how do i use that info to effect the display
permanently? and i assume remove the provided code.? i
did not have the serial link hooked up but it looks
like value 3 is the one i want. dave k7da
On
4/1/2019 7:30 PM, jjpurdum via Groups.Io wrote:
If it compiled and uploaded and ran, that's
what's important. What happened on screen? Did it
say Upload Complete?
Jack, W8TEE
On Monday, April 1, 2019, 10:08:59 PM EDT,
k7da <k7da@...>
wrote:
?it complies now but there are some warnings that i can figure out how to copy. dave k7da
On
4/1/2019 6:38 PM, jjpurdum via Groups.Io
wrote:
I said go INTO the setup() function
and place the code. You didn't.
It should be:
void
setup() {
// a
bunch of statements....
// At the
very bottom of setup, BUT INSIDE IT
? for (int i = 0; i < 4; i++) {
?? tft.setRotation( (uint8_t)
i);
?? tft.setCursor(10, 10);
?? tft.print("New rotation value of
");
?? tft.print(i);
?? delay(5000);?????? // You have
5 seconds to view the message
? }
Jack, W8TEE
On Monday, April 1, 2019, 7:24:21 PM
EDT, k7da <k7da@...>
wrote:
i got an error as follows
Arduino: 1.8.8 (Windows 10), TD:
1.45, Board: "Teensy 3.6, Serial,
180 MHz, Faster, US English"
dave k7da
On
4/1/2019 5:58 AM, jjpurdum via
Groups.Io wrote:
I assume that you have a
graphics object named tft.
Go into the
setup() function and add this
code at the bottom:
for (int i = 0; i
< 4; i++) {
??
tft.setRotation( (uint8_t) i);
??
tft.setCursor(10, 10);
?? tft.print("New
rotation value of ");
?? tft.print(i);
??
delay(5000);?????? // You have
5 seconds to view the message
}
and see if any of the
rotation values works for what
you need.
Jack, W8TEE
On Sunday, March 31, 2019,
11:26:30 PM EDT, k7da <k7da@...>
wrote:
i mounted the display upside down and turning it over makes it not fit the hole. so i need to turn the picture upside down. is that possible in sofeward or alectrically? dave k7da
On
3/31/2019 7:57 PM,
jjpurdum via Groups.Io
wrote:
What do you mean
"turned over"? There's
a Landscape and
Portrait mode
Jack, W8TEE
On Sunday, March
31, 2019, 10:29:40
PM EDT, k7da <k7da@...>
wrote:
can
the display be
turned over in
software?
dave
k7da
|
|
Re: display
Are you saying to see the main display page that looks like this: Jack, W8TEE
On Thursday, April 4, 2019, 6:51:30 PM EDT, k7da <k7da@...> wrote:
it did compile and and it id upload? the code works and now how
do i use that info to effect the display permanently? and i assume
remove the provided code.? i did not have the serial link hooked
up but it looks like value 3 is the one i want. dave k7da
On 4/1/2019 7:30 PM, jjpurdum via
Groups.Io wrote:
If it compiled and uploaded and ran, that's what's
important. What happened on screen? Did it say Upload
Complete?
Jack, W8TEE
On Monday, April 1, 2019, 10:08:59 PM EDT, k7da
<k7da@...> wrote:
?it complies now but there are some warnings that i can figure out how to copy. dave k7da
On
4/1/2019 6:38 PM, jjpurdum via Groups.Io wrote:
I said go INTO the setup() function
and place the code. You didn't.
It should be:
void setup() {
// a bunch of
statements....
// At the very bottom of
setup, BUT INSIDE IT
? for (int i = 0; i < 4; i++) {
?? tft.setRotation( (uint8_t)
i);
?? tft.setCursor(10, 10);
?? tft.print("New rotation value of ");
?? tft.print(i);
?? delay(5000);?????? // You have 5 seconds
to view the message
? }
Jack, W8TEE
On Monday, April 1, 2019, 7:24:21 PM EDT, k7da
<k7da@...>
wrote:
i got an error as follows
Arduino: 1.8.8 (Windows 10), TD: 1.45,
Board: "Teensy 3.6, Serial, 180 MHz, Faster,
US English"
dave k7da
On
4/1/2019 5:58 AM, jjpurdum via Groups.Io
wrote:
I assume that you have a graphics
object named tft. Go into the setup() function
and add this code at the bottom:
for (int
i = 0; i < 4; i++) {
??
tft.setRotation( (uint8_t)
i);
??
tft.setCursor(10, 10);
??
tft.print("New rotation value of ");
??
tft.print(i);
??
delay(5000);?????? // You have 5 seconds
to view the message
}
and see if any of the rotation values
works for what you need.
Jack, W8TEE
On Sunday, March 31, 2019, 11:26:30
PM EDT, k7da <k7da@...>
wrote:
i mounted the display upside down and turning it over makes it not fit the hole. so i need to turn the picture upside down. is that possible in sofeward or alectrically? dave k7da
On
3/31/2019 7:57 PM, jjpurdum via
Groups.Io wrote:
What do you mean "turned
over"? There's a Landscape and
Portrait mode
Jack, W8TEE
On Sunday, March 31, 2019,
10:29:40 PM EDT, k7da <k7da@...>
wrote:
can the display
be turned over in software?
dave k7da
|
|
Re: Clock and Control Cable Detail Figure 2-1
We'll take a look into redoing this, too. Jack, W8TEE
On Tuesday, April 2, 2019, 4:03:23 PM EDT, Vince Loschiavo <vince320@...> wrote:
Jack, Looks like this is also a bit of user doc that needs additional detail. Dave is making up cables and found that it isn't clear, or he hasn't found detail drawing/ schematic of those cables? could you provide so help? Thanks vince n2aie |
|
Re: display
If it compiled and uploaded and ran, that's what's important. What happened on screen? Did it say Upload Complete? Jack, W8TEE
On Monday, April 1, 2019, 10:08:59 PM EDT, k7da <k7da@...> wrote:
?it complies now but there are some warnings that i can figure out how to copy. dave k7da
On 4/1/2019 6:38 PM, jjpurdum via
Groups.Io wrote:
I said go INTO the setup() function and place
the code. You didn't.
It should be:
void setup() {
// a bunch of statements....
// At the very bottom of setup, BUT INSIDE IT
? for (int i = 0; i < 4; i++) {
?? tft.setRotation( (uint8_t)
i);
?? tft.setCursor(10, 10);
?? tft.print("New rotation value of ");
?? tft.print(i);
?? delay(5000);?????? // You have 5 seconds to
view the message
? }
Jack, W8TEE
On Monday, April 1, 2019, 7:24:21 PM EDT, k7da
<k7da@...> wrote:
i got an error as follows
Arduino: 1.8.8 (Windows 10), TD: 1.45, Board: "Teensy
3.6, Serial, 180 MHz, Faster, US English"
dave k7da
On
4/1/2019 5:58 AM, jjpurdum via Groups.Io wrote:
I assume that you have a graphics object named tft.
Go into the setup() function and add
this code at the bottom:
for (int i = 0; i < 4;
i++) {
?? tft.setRotation( (uint8_t)
i);
?? tft.setCursor(10, 10);
?? tft.print("New rotation
value of ");
?? tft.print(i);
?? delay(5000);?????? //
You have 5 seconds to view the message
}
and see if any of the rotation values works for
what you need.
Jack, W8TEE
On Sunday, March 31, 2019, 11:26:30 PM EDT,
k7da <k7da@...>
wrote:
i mounted the display upside down and turning it over makes it not fit the hole. so i need to turn the picture upside down. is that possible in sofeward or alectrically? dave k7da
On
3/31/2019 7:57 PM, jjpurdum via Groups.Io
wrote:
What do you mean "turned over"? There's
a Landscape and Portrait mode
Jack, W8TEE
On Sunday, March 31, 2019, 10:29:40
PM EDT, k7da <k7da@...>
wrote:
can the display be turned
over in software?
dave k7da
|
jjpurdum
Guy