CHECK OUT THE WIKI The purpose of the wiki is mainly to allow you to find information on instruments, either from either
- The model number
- The function(s) listed below. Some instruments have multiple functions - for example, the 4195A is a VNA, spectrum analyzer and an impedance analyzer. Therefore the 4195A is listed in multiple categories
Please also check out HPWiki available here:
- Accessory kits - various types
- AC power analyzers - PA2201A and PA2203A
- AC power supplies 6811C, 6812C, 6813C
- Airlines
- Arbitrary waveform generators M8194A
- Amplifiers?493A, 495A?
- Attenuators (optical) 8156A, 8157A, 8158B, 81566A, 81576A,?
- Attenuators (RF) 8494A
- Attenuator set (500 Ω) 350C
- Attenuator set (600 Ω) 350D
- Attenuator switch driver
- Audio analyzers? 8903A, 8903B, 8903E,? ?
- Base station test sets
- Bit error rate testers (BERTs)
- Cables
- Capacitance meters U1701A, U1701B, 4272A, 4278A, 4279A
- Capacitor Bridge 4270A,
- Capacitor standards 16380A, 16380C,?
- Carrier noise test setsi
- Cesium frequency standards
- Clamp ammeters
- Close field probes
- Crystal Impedance E4915A, E4916A
- Data Acquisition Systems (DAQs)
- DC power analyzers
- DC power supplies 6030A , 6031A , 6032A, 6033A, 6035A, 6131C, 6621A, 6622A, 6623A, 6624A, 6627A, 6255A, 6645A, 6671A, 6672A, 6673A, 6674A, 6675A, 62003A, 62003C, 62003E, 62004A, 62004B, 62004E, 62005A, 62005B, 62005E, 62006A, 62006B, 62006E, 62010A, 62010C, 62010E, 62012A, 62012C, 62012E, 62015A, 62015C, 62015E, 62018A, 62018C, 62018E, 62024A, 62024C, 62024E, 62028A, 62028C, 62028E, 62048A, 62048C, 62048E
- Delay lines
- Detectors
- Device current waveform analyzers
- Digital communications analyzers
- Directional couplers
- Distortion analyzers 330B, 330C, 330D, 331A, 332A, 333A, 334A, 339A, 8903A, 8903B, 8903E,???
- Dynamic measurement DC source
- Electrometers
- Fading simulators
- Femto ammeters
- Filters
- Frequency counters 522B, 5342A 5343A 5352B
- Frequency standards?
- Function Generators ? 3310A,? 8165A,
- GPIB controllers, extenders, cables etc.
- GPS frequency standards
- Harmonic mixers
- High resistance meters 4339B
- High resistance meter fixtures 16008B
- HEV EV Grid Emulators and Test Systems
- In-circuit test systems
- Impedance analyzers 4195A, 4291A, 4291B, 4395A, 4396A, 4396B, 4294A, E4990A, E4991A
- Impedance Analyzer Accessories
- Impedance / Gain Phase analyzer 4194A
- Impedance Meter 4193A,
- Isolators
- LCR meters? U1701A, U1701B, U1731A,? U1731B, U1731C, U1732A, U1732B, U1732C, U1733C, 4191A , 4192A, 4194A, 4195A, E4196A,? 4216A, 4260A, 4261A, 4262A? 4263A, 4263B, 4271B, 4274A, 4275A, 4276A , 4277A, 4284A, 4285A, 4286A, 4287A, 4291A, 4291B, 4294A, 4332A, 4342A, 4395A, 4396A, 4396B, E4980A and E4980AL
- LCR meter calibration devices? 16380A 42030A? 42090A, 42091A and 42100A
- LCR meter accessories
- 2-Terminal BNCs.
- 4-Terminal Pair (BNC connectors)
- Cable extension 16048A, 16048D, 16048E, 16048G, 16048H
- DC current bias accessories 42841A, 42842A, 42842B, 42842C, 42843A
- DC voltage bias accessories 16065A, 16065C,
- Kelvin clips 16089A, 16089B, 16089C,16089E
- Lead Components 16047A,16047B, 16047D, 16047E
- Material 16451B, 16452A
- Probes 42941A
- SMD 16034E, 16034G, 16034H
- 2-port 16096A
- 7 mm (APC7)
- 2-Terminal BNCs.
- LCZ meters? 4276A, 4277A,
- Lightwave clock / data receivers
- Lightwave converter
- Lightwave component analyzer
- Lightwave measurement system mainframes
- Lightwave polarization analyzers 8509B
- Logic analyzers
- Nemo wireless network solutions.
- Noise and interference test set
- Noise figure analyzers
- Noise sources 346A, 346B. 346C ,
- Matching pads (50 ohm to 75 ohm or similar)
- Materials test equipment
- Microwave repeaters
- Microwave downconverters 70427A
- Microwave / THz sources
- Milliammeter 428B
- Milliohm meter
- Mobile communications DC source
- Modular instruments
- AXIe
- Data acquisition (DAQ)
- USB
- PXIe
- Modulation analyzers
- Multimeters 427A, 970A
- Optical attenuators
- Optical heads
- Optical sources
- Optical spectrum analyzers
- Oscilloscopes 120A, 120AR, 120B, 122A, 130A, 130B, 130BR, 130C, 140A, 140B, 141A, 150A, 150AR, 160B, 180A, 180AR, 180CD, 181A, 181AR, 181T, 181TR, 182C, 182T, 183A, 183B, 184A, 184B, 185A, 185B, 1200A, 1200B, 1220A, 1221A, 1703A, 1707A, 1707B, 1710A, 1710B, 1715A, 1722A, 1725A, 1726A, 1740A, 1741A, 1742A, 1743A, 1744A, 1746A, 1980A, 1980B, 5403A, 6000A, 6000L, 16533A, 16534A, 54100A, 5410B, 54100C, 5100D, 54111D, 54120A, 54120B, 54200A, 54501A, 54502A, 54503A, 54504A, 54520A, 54520C, 54540A, 54540C, 54542A, 54542C, 54600B, 54601A, 54601B, 54602B, 54603B,? 54645A, 54654N, 54710A, 54720A, 54750A, 54825N, E1428,?
- Oven controlled crystal oscillators (OCXOs)
- Pattern generators
- PCM terminal test set
- Phase noise measurement
- Pico ammeters
- Printers 2225
- Plotters 7470A, 7475A?
- Probes
- Protocol analyzers and exercisers.
- Power booster test sets
- Power meters 431A, 431B, 431C, 432A, 435A, 435B, 437B, 438A
- Power splitters
- Power supplies
- Pulse generators
- Q-meters 4342A?
- Q-meter calibration inductors 16470A
- Reflection transmission test set
- Return loss module (optical)
- Relays / switches / switch matrices (optical)
- Relays / switches / switch matrices (RF)
- Resistor standards 42030A?and 42100A
- S-parameter test sets
- Scalar network analyzers
- SCSI bus preprocessor interface E2324A
- Selective level meters 3746A
- Semiconductors
- Semiconductor parameter analyzers 4145A, 4155B, 4156B,
- Signal analyzers
- Signal generators / sweep generators / signal sources / oscillators 200CD, 201B, 209A, 204D,? 608A,? 8165A
- Software
- Source measure units
- Spectrum analyzers 4195A,???
- Switch control units
- SWR meter 415E?
- Time interval? counters
- Time mark generator 226A
- Timing and data state modules
- Torque wrenches
- Transmitter testers
- Trigger modules
- Ultrasound transducers
- Universal bridge? 4260A, 4265A, 4265B?
- Vacuum tube voltmeter 410C
- Vector Impedance Meter 4193A, 4800A, 4815A
- Vector Network Analyzers (VNAs) 4195A,? 8510A, 8510B, 8510C, 8753A, 8753B, 8753C, 8753D, 8753E, 8753ES, 8752ET, 8719A, 8719B, 8719C, 8719D, 8720A, 8720B, 8720C, 8720D, 8720ES, 8722A, 8722B, 8722C, 8722D, 8722ES,
- Vector Network Analyzers (VNA) calibration kits 85032B, 85032E, 85033C, 85033D, 85033E, 85050B, 85050C, 85050D, 85052B, 85052C, 85052D, 85054A, 85054B, 85054D, 85056A
- Vector Network Analyzer (VNA) verification kits
- Vector Signal Analyzer 89650S, 89600S
- Vector voltmeters 8405A, 8508A,
- VXI mainframes 70000B, 70000C
- Waveform and function generators
- Waveguide to waveguide and waveguide to coaxial transitions.
- Wireless 58 OTA chambers
- Wireless channel emulators
- Wireless network emulators
- Wireless communication test sets
?
|
HP Meters
Anybody have a solution for the peeling meter faces commin on HP meters like
the 400EL?
73
Tom Dawson
WB3AKD
wb3akd@...
By
Tom Dawson
·
#98
·
|
|
PFcap query
Looking for some info on a broken cap..........Manual says it is a
selected part, with the ave value given as 5pf mica 10% 500vdcw (from
Hi Q div of Aerovox Corp Olean NY)Hp part no. is
By
Daveolla
·
#97
·
|
|
Re: Hewlett Packard Military Tube Type Oscilloscopes
Robert
For documentation you might like to check out the LOGSA site-
http://www.logsa.army.mil/etms/find_etm.cfm
Enter 'oscilloscope' in the 'TM Title text' search box.
Definitely some AN/USM-140C
By
Dave Brown <tractorb@...>
·
#96
·
|
|
Hewlett Packard Military Tube Type Oscilloscopes
Hello.
My name is Robert.
I am in search of some of the older Hewlett Packard Military (tube
type) oscilloscopes. I am currently in search of these (two)
particular models and the manuals at this
By
rom777772003 <romhifi@...>
·
#95
·
|
|
hp 7475a service manual
I am looking for a hp7475a service manual or schematic. I am working
on a project that includes this plotter with modifications. Any help
would be appreciated.
Rick Paul
By
brendart2000 <rpaul@...>
·
#94
·
|
|
Re: 8753C
Tom,
Couple of options for you:
1) HTML file (missing some graphics) that lists the
available commands for 8753C, D, and similar boxes.
Doesn't tell you how to use them. It's a small file,
123kb.
By
Dave W8NF <w8nflists@...>
·
#93
·
|
|
Re: HP 8672A odd problem.
How about the PD's reference and VCO inputs? My bet's on the YIG or tuning
driver circuit, or one of the supplies associated with them.
-- john KE5FX
By
John Miles <jmiles@...>
·
#92
·
|
|
HP 8672A odd problem.
Synthesizer lock on all frequencies but has about a 10 KHz FM signal on
most frequencies. Using a scope on the output pins of the Phase detector
chip shows the expected pulses but about a ten KHz
By
Tom Dawson
·
#91
·
|
|
8753C
Can anyone point me to a pdf or something on line with HPIB command list for
the 8753?
r
Tom
WB3AKD
By
Tom Dawson
·
#90
·
|
|
HP 6177C Current Source Manual
Does anyone have an operator's manual (or O/S manual) for the HP
6177C current source that they can lend me?
By
tbfowler100 <tfowler@...>
·
#89
·
|
|
Eurotherm 832
I sorry to get off topic but I have tried many forums looking for a
schematic for a Eurotherm 832 power supply.
Eurotherm list this with a 831 on their web site, but the 832 is
different.Eurotherm
By
dmac1054us <dmac1054@...>
·
#88
·
|
|
Re: Tektronics forums
Thanks to all for the replies.
The second one http://groups.yahoo.com/group/TekScopArc under files
had a copy of the schematic I needed. Both sites have information
under
By
dmac1054us <dmac1054@...>
·
#87
·
|
|
Re: Tektronics forums
Thank you, Jorgen.
Regards
Miroslav Pokorni
By
Miroslav Pokorni
·
#86
·
|
|
Wanted: HP 5355A Plug-in for HP 5345A Counter
Dear Colleagues,
I'm looking for a HP 5355A plug in (frequency converter) for use in
an HP 5345A counter.
Anyone who has a spare kindly email me at: cesium_mike@...
Regards,
Mike,
By
cesium_mike <drd@...>
·
#85
·
|
|
Re: Tektronics forums
<mpokorni2000@y...> wrote:
http://groups.yahoo.com/group/TekScopArc/
Jorgen
dj0ud
By
Jorgen Lund-Nielsen
·
#84
·
|
|
Re: Tektronics forums
Hello Doug,
What is the second Tek group.
Regards
Miroslav Pokorni
By
Miroslav Pokorni
·
#83
·
|
|
Re: Tektronics forums
thanks Fred
I did find 2 groups of interest for Tek on Yahurl.
Doug
<fwolsen@e...> wrote:
TekScopes@...
By
dmac1054us <dmac1054@...>
·
#82
·
|
|
5300A + 5302A check
I have a 5300A measuring system readout with a 5302A 50 Mhz counter. When I first turn the unit on, with the function knob dialed to "check" the counter reads 10.0000 Mhz but after it warms up for a
By
info@...
·
#81
·
|
|
Re: Tektronics forums
No, but there's a Tektronix group here on Yahurl. TekScopes@...
Fred
--
<><
--
Outgoing checked by Norton AV
By
Fred Olsen <fwolsen@...>
·
#80
·
|
|
Tektronics forums
Anyone know of any Tektronics forums?
thanks
Doug
By
dmac1054us <dmac1054@...>
·
#79
·
|