开云体育

Hi Mike, DOS/VS stores macros in compressed form, and that’s what SSERV returns. ESERV will decompress the macros in readable form. No macro comments though. Best regards, Steve Orso +1 610 217 7050

I'm trying to print the DTFSD macro source using SSERV with dos rel 34 : // JOB SSERV1 // EXEC SSERV DSPLY? E.DTFSD /* It's returning some kind of "binary" output. What am I missing ? thx Mike

In my opinion yes VSE fully supports LCS, I remember that OSA/SF software was available also for VSE. -- Piotr

I'm planning to use VM VCTCAs to connect VSE VTAM to OS/390 and VM. I have the patched version with LCS SNA support running and talking on my LAN from one OS/390 to another. The goal is to get POWER's

Jay What kind of emulated connection are you using? Is this patched Hercules version to send/receive SNA packages? Is it OSA LCS or QDIO? Or maybe CTC? Piotr

Jay, That's my mistake! When you asked for a way to edit them online my mind instantly assumed you were looking for a way to do it with configuration dialogs. Reading it again it seems that DITTO is

Rene, that's the kind of interface I was looking for. Thanks! David, I'd seen the dialogs, but I'd prefer to have more control over the contents of VTAMLST, mainly so I can enforce my preferred naming

You can use DITTO. Logon to SYSA, escape to CICS and start DITTO, then navigate with the menus. HTH, Rene FERLAND, Montreal

Hi Jay, Yes there is a way to do it online! In the interactive interface go to path 2 for Resource Definition. There you will find path 5 and 6, maintain VTAM Application Names and VTAM Startup

I'm working to get all of my Hercules systems talking to each other. I've got OS/390 speaking SNA to my other OS/390s on Hercules and my R/390s, so now it's time for next bit: getting VSE into the

Hi All, There are a couple of challenges to making a How-To.? Primary is that BOS started out as three different packages, announced in December, 1964: BOS 8K Disk, BOS 16K Disk, and BOS 16K Tape.?

Hello Steve, Thank you very much for taking your time at looking into that topic. ?On my side, I can add this: 1. I already use HercPrt with DOS/360, despite the absence of an end separator page, I

René Ferland wrote:? ?( /g/H390-DOSVS/message/141 ) Hi René, I looked at what I thought was George's DOS/VS distribution (now at: http://dosvs.31bits.net/ ).? It appears that it

Hi, Rene, I meant BOS/360. Please check out my You Tube channel: ==> dosvsoperator!!!

You mean me? or BOS/360? or this discussion group? or maybe all of these? :-) Cheers, Rene FERLAND, Montreal

It's not very chatty. Please check out my You Tube channel: ==> dosvsoperator!!!

wrote: I've previously suggested the HRTPB360 program that came with HASP from the 1970s and is still distributed byte-for-byte unchanged with the latest z/OS. This can be assembled to run on either a

I've been looking for Model 20 software, it should not be hard to add a IBM360/20 model to my IBM360 simulator. I am also looking for model 20 microcode listings or CLD's. There was also a similar

My data processing career started in 1962 when I went to a technical school to learn how to wire the control panels and to operate IBM Punched Card Tabulating Equipment. My introduction to the IBM 360

Hi René Solved! I was doing two things wrong 1) Pressing <ENTER> on teraterm so input for IPL comands was set to master console. If you do not press <ENTER>, input is set to card reader on devinit