开云体育

Hello group, Recently my trusty old Gemini I shot craps after 19 yrs of faithful service. I had to upgrade to the new Gemini 2 and Hand Controller. As you know, the old Gemini I connected to a PC via

Sorry me typing not thinking No a 15 pin VGA will not work as it is 3 rows DB15.?? You need two rows DB15.?? You can buy longer versions of what you have but try to get 2m at least.??? Also

Brendan, Are you saying that a standard VGA cable will work? I have several of those laying around. I don’t understand your comment about “Aldo”. Is that a particular manufacturer? Or is this a

Yes I replaced one for user recently. ?Same issue. ?But they fail near the pins so doing a jumper is not so easy. ? ?DB15 Male /Female 2m or a little more. ? ?Mouser or Digikey. ? There are

Sorry for the delayed answer. Yesterday I was playing with the mount and noticed the North button was working again. After a few experiments I found that it was indeed the cable between the HC and the

I had this exact same problem. I too thought it might be the HC. Turns out all I did was replace the button battery in the main Gemini box (not the HC). Replaced battery and all is well. Scott

So, what happened? -- Chip Louie Chief Daydreamer Imagination Hardware Astrospheric - South Pasadena Astrospheric Signature ( https://www.astrospheric.com/?Latitude=34.114268&Longitude=-118.1400894 )

Brendan, Thanks for the additional info. I will test this tomorrow. Bill

Hi Bill, I'm home now so can attach more info on this: Just remember the "DEC+" out (Pin 9 HC)? becomes DEC "-ve" when "REV DEC" is selected.??? This is why the fault appears to change.?? In

Bill id suggest it’s a cable issue or pin not contacting socket properly. The HC button is ok. ?Selecting “Rev” proves this. ?But it also uses the same “Dec+” wire out as “Dec -“ when

On Tue, Sep 10, 2024 at 02:37 PM, Bill Tschumy wrote: > > Michael Hermann also thinks the logic chip is the likely culprit. ?Can you > even get another of those now a days? > > I did try a CMOS reset

Michael Hermann also thinks the logic chip is the likely culprit. Can you even get another of those now a days? I did try a CMOS reset but that didn't fix the problem. I don’t have another HC cable

Just happens to be one for sale on eBay. (

It could be a broken wire in the HC cable, too. René Am 10.09.24 um 18:44 schrieb Will:

I don't know what is closest to a general reset to factor settings for Gemini 1 but maybe try a "Restore to Defaults" and manually reconfiguring the Gemini-1?? IDK the Gemini hardware but maybe the

Bill, It must be the I.C. (although I have not seen the schematic of the HandBox) as you have eliminated the actual switch with your testing method.? I need to take apart my Handbox to see just what

Group, In the past couple of days, the north Dec button on my 14 year old GM8 hand controller has stopped working. The attachment shows the type of HC I have. Pressing the north button alone does

Greetings, , However unlikely, a second washer may have? been added because the bolt it too long or the washer was too thin. For what it's worth, washers are used to increase the surface area of the

Thank you Paul and Chip Louie for the valuable advice, I hope it will be helpful for other users who have the same doubts/problems as me. Regards, Thomas Bianchi [email protected]> ha scritto:

On Mon, Sep 2, 2024 at 12:40 PM, Thomas Bianchi wrote: > > Thanks Paul, > but if I put stainless washers the resistance is the same or it also > depends on the material, i.e. in this case the original