开云体育

Thank you everyone, great suggestions. I unplugged the cables to both servos and turned on the Gemini 2 and the rapid beeping still happily continues.???♂? Thanks Brendan for the PIC

Bob Chip could be very correct that the ver1 Dspic33 firmware may well work but also may have unintended issues.?? The Beep could have been part of new lvl6 stall detection that works with lvl3

Have a look at the documents in the Files subfolder - /g/Gemini-II/files/+++%20Gemini%202%20Level%206%20Upgrade%20+++ Ken

If it is working now just run GFU with all options checked and pick L6.1 from the menu.? This will restore the missing files and no more 404 errors. -- Chip Louie Chief Daydreamer Imagination

Hi Bob, Did the beeping stop?? Here is an Amazon link to one of the PIC programmers I have used, *PIC PICKit3 kit* ( https://www.amazon.com/SUPERELE-PICKIT3

Many thanks for your patience Chip and Brandon, thank you so very much for taking the time to help me, simply wonderful. It is so great to have the high-end precision Losmandy G11 mount and Gemini 2,

I’d be pretty surprised if it wasn’t playing up without the lvl 3.+ dsPIC33 firmware. if you flash GFU back to lvl 5 ensure you reset HGM Defaults and then all your settings cheers -- Brendan

I’m sorry for so many posts. I’m using GFU, I have now tried twice, selecting to install Gemini 5, the 2nd time I selected to format the SD before the firmware install, and both times it installed

Hi Bob, You worked out most of it yourself before I could reply, good job, most folks just wimp out and say it doesn't work, hang in there!? So now that it is talking via Ethernet you can see all of

As I read more, I think my problem is that I have not purchased / installed the v 6 servo pic programmer, at this point I think I need to go back to v 5 firmware. Please let me know if you’ve got

Thanks Brendan: Sorry, I’m new at this, unsure where to check the dsPIC33 firmware. If this is for the Servos, they are V 1.0. BTW, the error started right after going from 5.1 to the 6.0 update

Bob what is your dsPIC33 firmware lvl? cheers -- Brendan

Hi Chip: I was able to manually reset my laptop IP to: IP: 192.168.0.100 Subnet: 24 Gateway: 192.168.0.1 DNS: 192.168.0.1 The HC V1.60 and Mainboard 6.00 Firmware update worked.? However, I am now

Hi Chip: I followed your instructions, still a no go. My Gemini 2 network is set to the defaults IP Address: 192.168.0.111 Netmask: 255.255.255.0 Default Gateway: 192.168.0.1 Primary DNS Server:

Hi Bob, Using the Gemini-2 Hand Controller boot up and go to the Top/Main Diamond button menu. From the main Menu press > System > Reset HGM Defaults.? Wait for the Gemini-2 to reboot then do a power

Greetings: my older version Gemini 2 seems to be working okay, good internal 3v battery, version 5.1 firmware. I launched the firmware updater and it couldn’t connect on either Ethernet or USB from

It also helps to use an eyepiece that yields moderate power with an illuminated reticle/ cross hair during alignment.? Seriously, apparently many of not most people have no idea where the actual

IME if you do three stars on one side of the meridian then move the mount to the other side and align on one more star you will get a better model. -- Chip Louie Chief Daydreamer Imagination Hardware

Everything seem to work now, except that some of the menu items ?on the embedded web-server? (HandControl, MobileHandControl, Manual and Serial Command Set) return a 404 (not found) error. So

I don't know if this will help or not now but here goes.? Might help for the future. I just completed the update to L6.1.? Unfortunately, I can't use the GFU or the Flash Firmware command on the