开云体育

Hi all, My Reverse RA & DEC options are enabled, causing my mount to slew to the opposite side of the pier than my target. Ive tried to reset the HGM parameters and then re-setup the Gemini II with

Actually the G1 could cope with up to 32k ticks Sent: 15 March 2025 23:40 To: [email protected] Subject: Re: [Gemini-II_io] I don't understand why Losmandy disabled the port for the axis encoders

I certainly agree that for imaging GOTO is the only way to fly. But if you get out to a dark sky site guided PUSH-TO involves the observer in the process of acquisition and observation.? It's a

Hi Les, Sometimes the SD card in the hand controller is loose and making intermittent contact. Reseating and securing it in place can help in that case.

I've moved on from push-to operation to fully automated Goto in the late 90's. With light pollution getting worse, clear nights getting fewer, and my desire to get as much imaging done while sleeping

The reason the support for the encoders was dropped is nobody used encoders with the Gemini.? The Gemini only allowed the use of relatively low resolution encoders, 10K max. too low to be truly

The problem is almost always with the cable.? Check both ends and see if the contacts are dirty.

Hi folks... hoping this group is still available..? Anyway, my problem is with my hand held controller. First of all I mainly use my laptop to control the mount. However, I wanted to shoot the eclipse

The code for the Gemini-2 was a complete re-write for a new platform. As I said,I believe it was a business decision not to write code to support encoders attached to Port “E”, because the number

I don't understand why Losmandy disabled the port for the axis encoders on the Gemini II. It was present on the Gemini I, so Losmandy wouldn't have to reinvent the wheel. The reason: There would be so

On Wed, Mar 12, 2025 at 02:53 PM, PAT&SANDY wrote: > > > > Hello !?? this question is somewhat along this current topic.? I have two > older Gemini 2 units on MI- 250 mounts. I have never updated

Hey Paul, Thanks! I read through the instructions and it seems pretty straight forward. I ordered a Pic 3 kit on Amazon (the recommended on was not available, but I found a different one. Looking

If you use NINA, there’s a plug-in that does just that. You slew the scope to the different obstructions and NINA will know what to do with the info, in essence creating a “virtual horizon” for

If Theodelite depends on the phone's sensors, I doubt it would work very well. My phone, when set for true north, is at least 15 degrees off. (And where I live, in Virginia, has about a 10 degree

On Wed, Mar 12, 2025 at 05:53 PM, PAT&SANDY wrote: > > > > Hello !?? this question is somewhat along this current topic.? I have two > older Gemini 2 units on MI- 250 mounts. I have never updated

Not sure about accuracy for gaps in folliage, but I use Theodelite for mapping treelines. https://apps.apple.com/us/app/theodolite/id339393884 I don't see an Android version. Dave

Hello ! this question is somewhat along this current topic. I have two older Gemini 2 units on MI- 250 mounts. I have never updated the firm wear on the unit or hand controller. I have the kiss of

On Tue, Mar 11, 2025 at 10:44 PM, Jason Hissong wrote: > > > > So I figured it out. Apparently, it helps when you don't fat finger a > comma in the IP address. I was able to successfully upgrade and

Some instructions for doing this yourself here: /g/Gemini-II/files/+++%20Gemini%202%20Level%206%20Upgrade%20+++/UNOFFICIAL%20PICKIT3%20REFERENCE%20ONLY%20for%20DIYers Other files in

Ok great. I will probably go that route as I have experience doing that type of thing. Are the files/instructions available to properly flash the servo firmware? Thanks so much! My GM811 is humming