开云体育

I was resetting the worm mesh on my G11 (I'd been getting RA stalls) and during testing I hit the RA safety limit. My problem is that I couldn't use the arrow keys on the HC to move the mount after

Just a quick follow-up.? I fired up Gemini last night and the date on the HC was accurate.

Paul, I'm sure I've found the solution to solve this issue, though I don't know exactly the mechanism of the problem. My Gemini-2 for CG-11 (SLW&OPW) was directly connected to my NUC #2 without

Paul, Following your reply, I've changed my PC, which is connected to CG-11's Gemini-2, to other PCs.? I've got very interesting results. #1 Gemini-2 === Intel NUC #2: has slow response problems #2

I may have done those resets as well since they are in the afternoon right before I grab the log.

Hi masami, The error in the ASCOM log shows that the driver can't connect to Gemini using FTP protocol (this is used to retrieve the list of PEC files stored on the SD card): 10:48:30.983 Exception?

Hi, I have two Gemini-2 units.? One for my CG-11 (OPW+SLW upgraded) and G-11 (OPW only). For CG-11's Gemini-2, I've noticed that the response time when I select "Configure PEC" on virtual HC is very

Hi Paul, Next time I will use Gemini Troubleshooting Reporter.? According to the forecast, the weather here will not be cooperative in a few weeks or so. By the way, I don't know this issue is

Did you also do a few reboots/resets on Feb 28? It looks like there were two WD Resets on that date, also.

Hi Paul, I will follow your suggestion. I have cloudy nights for the next week, I can try in the future. Looking at those timestamp of events, they may be I was doing the reset. I used the web UI to

Hi masami, Like I asked Seokman, can you please go to the Gemini.NET virtual hand controller, connect to Gemini and collect a troubleshooter log zip file and upload it here? Seokman appears to have a

Hi Seokman, Thanks for uploading this! Looking into Gemini status log, it appears you've been experiencing very frequent restarts after a watchdog reset events (WD Reset). Here are some of the latest:

I do see the same pattern on my ASCOM log file. 01:57:21.910 UDP connection ? ? ? ? ? ?TID:11 [2]: gemini, 11110 01:57:21.910 Looking up DHCP name ? ? ?TID:11 [2]: gemini 01:57:23.762

Hi Paul, Thank you for your guick feedback. Yes, after I found my Gemini-2 was disconnected, I tried to connect to it from the virtual HC several times.? But no avail. At that time, as I wrote

Hi Paul, I uploaded the reporting Zip file to files section. /g/Gemini-II/files/Gemini%20Troubleshooting%20Log/Gemini%20Telescope%20Driver%20Report.zip One more thing I noticed is

Hi masami, Thanks for the log. A bit of a strange behavior from PHD2 -- it

If PEC checkbox is on in the driver virtual hand-controller, then Gemini is reporting that PEC is being used. But, Gemini becoming unresponsive sounds like a bigger issue. If you use Ethernet to

I actually updated to the new firmware and the software in January and noticed this PEC turning off problem. Last couple of nights I? got clear nights and both nights PEC appears to be off from

I know the ASIAIR plate solves just fine on my M10" LX200 f/6.3 SCT which has significant coma at the outer edges.? While I have not personally tried it on the M8" LX200 f/10 ACF OTA but based on the

During my guiding session, suddenly PHD2 reported that the mount was not connected on the remote desktop screen.? Indeed the virtual HC's connect button showed "connect."??So I went to the roof and