|
what is the thread pitch of a daltin headstock (Lot 4)?
|
|
|
For the spindle its 1 1/4 - 12 threads per inch. This size is for the Lot 2
3 4 and 5. Lot 6 and the Dalton 9 is 1 7/8 - 8. Not sure what the 10 1/2
inch had as there is only a couple known of and no one in this group has one
of the three I know of. Dennis who's email just started working again after
being down for a month for some reason. Its Frontier what can I say:-((((
toggle quoted message
Show quoted text
-----Original Message----- From: [email protected][mailto: [email protected]] On Behalf Of Grey Pilgrim Sent: Friday, August 20, 2021 5:56 PM To: [email protected] Subject: [DaltonLathes] I have a silly question what is the thread pitch of a daltin headstock (Lot 4)? Scanned by McAfee and confirmed virus-free. Find out more here:
|
Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :)
toggle quoted message
Show quoted text
Spindle thread?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim < pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
|
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you happen to decide that you are not going use yours, please let me. Happy to buy it off you.
Glenn B up in?
toggle quoted message
Show quoted text
On Aug 20, 2021, at 7:37 PM, Grey Pilgrim < pilgrim23@...> wrote: Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :) -Bart
Spindle thread?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim < pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
|
Glen B got one you could swap? ?I mean of a different sort like for an Atlas or Craftsman or the like? ?
toggle quoted message
Show quoted text
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you happen to decide that you are not going use yours, please let me. Happy to buy it off you.
Glenn B up in? Woodinville, Wa Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :) -Bart
Spindle thread?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim < pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
|
Alas, nothing in smaller sizes. Just the one little 5” original chuck off the Dalton, which now has the jaws so bell shaped as to be worthless.?
I do have a hugmongous 12” two jaw going to waste, and a couple of 12” faceplates- set up for d1-4 cam locks. New, never used. ?But that’s it...
toggle quoted message
Show quoted text
On Aug 20, 2021, at 8:05 PM, Grey Pilgrim < pilgrim23@...> wrote: Glen B got one you could swap? ?I mean of a different sort like for an Atlas or Craftsman or the like? ?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you happen to decide that you are not going use yours, please let me. Happy to buy it off you.
Glenn B up in? Woodinville, Wa Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :) -Bart
Spindle thread?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim < pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
|
oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out a deal
toggle quoted message
Show quoted text
Alas, nothing in smaller sizes. Just the one little 5” original chuck off the Dalton, which now has the jaws so bell shaped as to be worthless.?
I do have a hugmongous 12” two jaw going to waste, and a couple of 12” faceplates- set up for d1-4 cam locks. New, never used. ?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different sort like for an Atlas or Craftsman or the like? ?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you happen to decide that you are not going use yours, please let me. Happy to buy it off you.
Glenn B up in? Woodinville, Wa Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :) -Bart
Spindle thread?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim < pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
|
As I have been off line for some time you guys? need to
know that all the Dalton and other lathes I had on display at my business are
now at my home in McMinnville.? So I have 30 machines all restored in wonderful
condition that need to find a new home.? If anyone is interested contact
me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL with
overhead gear drive a two Lot 6 lathes one 1917 that is basically brand new and
the one I restored and used to build a couple of? model steam engines with
that? is a really nice lathe with lots of upgrades.? Also have a few
South Bend lathes and three Atlas lathes. ?Couple of more odd ball lathes.
?
Dennis
?
?
oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out
a deal
?
Alas, nothing in smaller sizes. Just the one little 5”
original chuck off the Dalton, which now has the jaws so bell shaped as to be
worthless.?
I do have a hugmongous 12” two jaw going to waste, and
a couple of 12” faceplates- set up for d1-4 cam locks. New, never used.
?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different
sort like for an Atlas or Craftsman or the like? ?
?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you
happen to decide that you are not going use yours, please let me. Happy to buy
it off you.
Woodinville, Wa
?
Yes Glen. I have a weird project; ?not for a dalton BUT
I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I
also have a toasted Grizzly G0602 tail stock; ?it is not repairable but
the center shaft on it is 1/14 or ? the right size to fit that 3
jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock
fixture for a project at hand ?while my new Grizzly tail stock is on order
($400 bucks ?Ouch!) ?-I said it was weird :)
-Bart
?
?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote:
what is the thread pitch of a
daltin headstock? (Lot 4)?
?
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
|
I would be interested in the lot 6 you got out of long island and the foot powered one too. Rick
On Sat, Aug 21, 2021 at 1:32 AM, Dennis Turk <dennis.turk2@...> wrote:
As I have been off line for some time you guys? need to
know that all the Dalton and other lathes I had on display at my business are
now at my home in McMinnville.? So I have 30 machines all restored in wonderful
condition that need to find a new home.? If anyone is interested contact
me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL with
overhead gear drive a two Lot 6 lathes one 1917 that is basically brand new and
the one I restored and used to build a couple of? model steam engines with
that? is a really nice lathe with lots of upgrades.? Also have a few
South Bend lathes and three Atlas lathes. ?Couple of more odd ball lathes.
?
Dennis
?
?
oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out
a deal
?
Alas, nothing in smaller sizes. Just the one little 5”
original chuck off the Dalton, which now has the jaws so bell shaped as to be
worthless.?
I do have a hugmongous 12” two jaw going to waste, and
a couple of 12” faceplates- set up for d1-4 cam locks. New, never used.
?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different
sort like for an Atlas or Craftsman or the like? ?
?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you
happen to decide that you are not going use yours, please let me. Happy to buy
it off you.
Woodinville, Wa
?
Yes Glen. I have a weird project; ?not for a dalton BUT
I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I
also have a toasted Grizzly G0602 tail stock; ?it is not repairable but
the center shaft on it is 1/14 or ? the right size to fit that 3
jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock
fixture for a project at hand ?while my new Grizzly tail stock is on order
($400 bucks ?Ouch!) ?-I said it was weird :)
-Bart
?
?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote:
what is the thread pitch of a
daltin headstock? (Lot 4)?
?
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
|
I am interested in an Atlas or South Bend Dennis
toggle quoted message
Show quoted text
As I have been off line for some time you guys? need to
know that all the Dalton and other lathes I had on display at my business are
now at my home in McMinnville.? So I have 30 machines all restored in wonderful
condition that need to find a new home.? If anyone is interested contact
me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL with
overhead gear drive a two Lot 6 lathes one 1917 that is basically brand new and
the one I restored and used to build a couple of? model steam engines with
that? is a really nice lathe with lots of upgrades.? Also have a few
South Bend lathes and three Atlas lathes. ?Couple of more odd ball lathes. ? Dennis ?
? oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out
a deal
?
Alas, nothing in smaller sizes. Just the one little 5”
original chuck off the Dalton, which now has the jaws so bell shaped as to be
worthless.?
I do have a hugmongous 12” two jaw going to waste, and
a couple of 12” faceplates- set up for d1-4 cam locks. New, never used.
?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different
sort like for an Atlas or Craftsman or the like? ?
?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you
happen to decide that you are not going use yours, please let me. Happy to buy
it off you.
Woodinville, Wa
?
Yes Glen. I have a weird project; ?not for a dalton BUT
I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I
also have a toasted Grizzly G0602 tail stock; ?it is not repairable but
the center shaft on it is 1/14 or ? the right size to fit that 3
jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock
fixture for a project at hand ?while my new Grizzly tail stock is on order
($400 bucks ?Ouch!) ?-I said it was weird :)
-Bart
?
?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote:
what is the thread pitch of a
daltin headstock? (Lot 4)?
?
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
|
You two guys that are interested in one of my restored machines
email me at dennis.turk2@...
and we can talk off of the group.? Dennis
?
?
I am interested in an Atlas or South Bend Dennis
?
As I have been off line for some time you guys? need to
know that all the Dalton and other lathes I had on display at my business are
now at my home in McMinnville.? So I have 30 machines all restored in
wonderful condition that need to find a new home.? If anyone is interested
contact me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL
with overhead gear drive a two Lot 6 lathes one 1917 that is basically brand
new and the one I restored and used to build a couple of? model steam
engines with that? is a really nice lathe with lots of upgrades.?
Also have a few South Bend lathes and three Atlas lathes. ?Couple of more
odd ball lathes.
?
Dennis
?
?
oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out
a deal
?
Alas, nothing in smaller sizes. Just the one little 5”
original chuck off the Dalton, which now has the jaws so bell shaped as to be
worthless.?
I do have a hugmongous 12” two jaw going to waste, and
a couple of 12” faceplates- set up for d1-4 cam locks. New, never used.
?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different
sort like for an Atlas or Craftsman or the like? ?
?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you
happen to decide that you are not going use yours, please let me. Happy to buy
it off you.
Woodinville, Wa
?
Yes Glen. I have a weird project; ?not for a dalton BUT
I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I
also have a toasted Grizzly G0602 tail stock; ?it is not repairable but
the center shaft on it is 1/14 or ? the right size to fit that 3
jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock
fixture for a project at hand ?while my new Grizzly tail stock is on order
($400 bucks ?Ouch!) ?-I said it was weird :)
-Bart
?
?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote:
what is the thread pitch of a
daltin headstock? (Lot 4)?
?
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
|
For you guys that? do not have a quick change tool post for
your Dalton yet there are some great deals on eBay right now.? I just got
an OXA set with three extra number 1 tool holders free freight for 124
bucks.? You can actually get a standard set of tool post and fives holders
for less than $100 right now.? The ones I got came out of Comifornia
though they were made in Chinky land.? Rock hard and will ring a file so
make of good material the finish work is outstanding with all surfaces ground
then after black oxide coating was applied they had the working surfaces ground
again to a very fine finish.? I have never seen an Aloris site that was
finished this well.? The OXA is the perfect size for your lot 2 3 4 and 5
lathes and I also recommend this set for a Lot 6 as the distance from the top
of the compound to the center line of the spindle is the same on all
Daltons.? Even the Dalton 9.? I have used a OXA on the Lot 6 I used
down at my coast shop and built two steam engines with that lathe.? By the
way as much as I hate to let that lathe go its about the best Dalton I have bar
none.? This Dalton is the next to the newest one we know of.? Purchased
in June? of 1929 in Seattle Washington.
?
?
You two guys that are interested in one of my restored machines
email me at dennis.turk2@...
and we can talk off of the group.? Dennis
?
?
I am interested in an Atlas or South Bend Dennis
?
As I have been off line for some time you guys? need to
know that all the Dalton and other lathes I had on display at my business are
now at my home in McMinnville.? So I have 30 machines all restored in
wonderful condition that need to find a new home.? If anyone is interested
contact me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL
with overhead gear drive a two Lot 6 lathes one 1917 that is basically brand
new and the one I restored and used to build a couple of? model steam
engines with that? is a really nice lathe with lots of upgrades.?
Also have a few South Bend lathes and three Atlas lathes. ?Couple of more
odd ball lathes.
?
Dennis
?
?
oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out
a deal
?
Alas, nothing in smaller sizes. Just the one little 5”
original chuck off the Dalton, which now has the jaws so bell shaped as to be
worthless.?
I do have a hugmongous 12” two jaw going to waste, and
a couple of 12” faceplates- set up for d1-4 cam locks. New, never used.
?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different sort
like for an Atlas or Craftsman or the like? ?
?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you
happen to decide that you are not going use yours, please let me. Happy to buy
it off you.
Woodinville, Wa
?
Yes Glen. I have a weird project; ?not for a dalton BUT
I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I
also have a toasted Grizzly G0602 tail stock; ?it is not repairable but
the center shaft on it is 1/14 or ? the right size to fit that 3
jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock
fixture for a project at hand ?while my new Grizzly tail stock is on order
($400 bucks ?Ouch!) ?-I said it was weird :)
-Bart
?
?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote:
what is the thread pitch of a
daltin headstock? (Lot 4)?
?
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
|
When I set a OXA up on a Dalton this is the way I do it.? I
make a round spacer that is 5/16 inch thick to go under the tool post.?
This brings the tool holders to the center of the tool post when using 10 MM or
3/8 square shank insert tool holders.? I really do recommend this set up
for your Dalton. This also means I make a new tool post stud to mount the tool post
to the compound.? Also you have to machine the tool post Tee bolt to fit
your compound.? Again Dalton Tee slots in the compound slide are the same
for all lot numbers even the Dalton 9 inch. Also a short video of one of the
engines I built on my really nice Lot 6. The one picture is where I am
machining the cylinder bore on the steam engine using a 6 inch four jaw
chuck.? Held the bore to within .0005 on an old 1929 latheJ
?
?And as you can see I am a bit bored today.? For them
that don’t know it I know live alone now as my wife is now in a care home
for memory challenged people.? I just could not take care of her any
longer.? Sad but that is what happens when you get old sometimes.
?
?
For you guys that? do not have a quick change tool post for
your Dalton yet there are some great deals on eBay right now.? I just got
an OXA set with three extra number 1 tool holders free freight for 124
bucks.? You can actually get a standard set of tool post and fives holders
for less than $100 right now.? The ones I got came out of Comifornia
though they were made in Chinky land.? Rock hard and will ring a file so
make of good material the finish work is outstanding with all surfaces ground
then after black oxide coating was applied they had the working surfaces ground
again to a very fine finish.? I have never seen an Aloris site that was
finished this well.? The OXA is the perfect size for your lot 2 3 4 and 5
lathes and I also recommend this set for a Lot 6 as the distance from the top
of the compound to the center line of the spindle is the same on all
Daltons.? Even the Dalton 9.? I have used a OXA on the Lot 6 I used
down at my coast shop and built two steam engines with that lathe.? By the
way as much as I hate to let that lathe go its about the best Dalton I have bar
none.? This Dalton is the next to the newest one we know of.? Purchased
in June? of 1929 in Seattle Washington.
?
?
You two guys that are interested in one of my restored machines
email me at dennis.turk2@...
and we can talk off of the group.? Dennis
?
?
I am interested in an Atlas or South Bend Dennis
?
As I have been off line for some time you guys? need to
know that all the Dalton and other lathes I had on display at my business are
now at my home in McMinnville.? So I have 30 machines all restored in wonderful
condition that need to find a new home.? If anyone is interested contact
me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL with
overhead gear drive a two Lot 6 lathes one 1917 that is basically brand new and
the one I restored and used to build a couple of? model steam engines with
that? is a really nice lathe with lots of upgrades.? Also have a few
South Bend lathes and three Atlas lathes. ?Couple of more odd ball lathes.
?
Dennis
?
?
oh well, it was worth a shot. ?email me at pilgrim23@... ?we can work out
a deal
?
Alas, nothing in smaller sizes. Just the one little 5”
original chuck off the Dalton, which now has the jaws so bell shaped as to be
worthless.?
I do have a hugmongous 12” two jaw going to waste, and
a couple of 12” faceplates- set up for d1-4 cam locks. New, never used.
?But that’s it...
Glenn B
Glen B got one you could swap? ?I mean of a different sort
like for an Atlas or Craftsman or the like? ?
?
Hey Gray Pilgrim,
I’ve been looking for a dalton backplate. ?If you
happen to decide that you are not going use yours, please let me. Happy to buy
it off you.
Woodinville, Wa
?
Yes Glen. I have a weird project; ?not for a dalton BUT
I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I
also have a toasted Grizzly G0602 tail stock; ?it is not repairable but
the center shaft on it is 1/14 or ? the right size to fit that 3
jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock
fixture for a project at hand ?while my new Grizzly tail stock is on order
($400 bucks ?Ouch!) ?-I said it was weird :)
-Bart
?
?
On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote:
what is the thread pitch of a
daltin headstock? (Lot 4)?
?
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
?
?
|
|
Scanned by
and confirmed virus-free.
|
?
|
just for info on this… ?this is why I asked:?
|
Dennis I have tried and tried to contact you via email ? I am pilgrim23@...? please email me, ?I am VERY interested in any you could ?part with.
toggle quoted message
Show quoted text
As I have been off line for some time you guys? need to know that all the Dalton and other lathes I had on display at my business are now at my home in McMinnville.? So I have 30 machines all restored in wonderful condition that need to find a new home.? If anyone is interested contact me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL with overhead gear drive a two Lot 6 lathes one 1917 that is basically brand new and the one I restored and used to build a couple of? model steam engines with that? is a really nice lathe with lots of upgrades.? Also have a few South Bend lathes and three Atlas lathes. ?Couple of more odd ball lathes. ? Dennis ? ? oh well, it was worth a shot. ?email me at ?pilgrim23@...??we can work out a deal ? Alas, nothing in smaller sizes. Just the one little 5” original chuck off the Dalton, which now has the jaws so bell shaped as to be worthless.? I do have a hugmongous 12” two jaw going to waste, and a couple of 12” faceplates- set up for d1-4 cam locks. New, never used. ?But that’s it... Glenn B Glen B got one you could swap? ?I mean of a different sort like for an Atlas or Craftsman or the like? ? ? Hey Gray Pilgrim, I’ve been looking for a dalton backplate. ?If you happen to decide that you are not going use yours, please let me. Happy to buy it off you. Woodinville, Wa ? Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :) -Bart ? ? On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim < pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
?
?
? ?
| Scanned by??and confirmed virus-free. |
?
|
Hi Bart? Well as always Frontier is a bit of a hit and miss service.? I am down at my Florence home right now and Frontier gets really confused when I use two different computers.? Everytime I change computers they keep asking me for my email pass word for two to four days before they finally decide its me.? I? haves several lathes you might be interested in.? Not any of the restored ones but I have several wide bed 9 inch lathes one with the overhead drive.? It’s a tool room version with the power feed apron.? I also have a floor model SB 8 Jr. on floor legs.? I will be back in Mc later next week. ? Dennis ? Sent from for Windows ?
toggle quoted message
Show quoted text
From: Grey PilgrimSent: Thursday, August 26, 2021 6:25 PM To: [email protected]Subject: Re: [DaltonLathes] I have a silly question ? Dennis I have tried and tried to contact you via email ? I am pilgrim23@...? please email me, ?I am VERY interested in any you could ?part with. ? As I have been off line for some time you guys? need to know that all the Dalton and other lathes I had on display at my business are now at my home in McMinnville.? So I have 30 machines all restored in wonderful condition that need to find a new home.? If anyone is interested contact me.? Two Lot 5 lathes one 30 and one 36 inch.? A Dalton TL with overhead gear drive a two Lot 6 lathes one 1917 that is basically brand new and the one I restored and used to build a couple of? model steam engines with that? is a really nice lathe with lots of upgrades.? Also have a few South Bend lathes and three Atlas lathes. ?Couple of more odd ball lathes. oh well, it was worth a shot. ?email me at?pilgrim23@...??we can work out a deal Alas, nothing in smaller sizes. Just the one little 5” original chuck off the Dalton, which now has the jaws so bell shaped as to be worthless.? I do have a hugmongous 12” two jaw going to waste, and a couple of 12” faceplates- set up for d1-4 cam locks. New, never used. ?But that’s it... Glen B got one you could swap? ?I mean of a different sort like for an Atlas or Craftsman or the like? ? I’ve been looking for a dalton backplate. ?If you happen to decide that you are not going use yours, please let me. Happy to buy it off you. Yes Glen. I have a weird project; ?not for a dalton BUT I happen to have a spare 3 jaw chuck with a dalton back plate on it. ?I also have a toasted Grizzly G0602 tail stock; ?it is not repairable but the center shaft on it is 1/14 or ? the right size to fit that 3 jaw’s threads. ?My Idea was to make a spinning 3 jaw tail stock fixture for a project at hand ?while my new Grizzly tail stock is on order ($400 bucks ?Ouch!) ?-I said it was weird :) On Fri, Aug 20, 2021 at 5:56 PM Grey Pilgrim <pilgrim23@...> wrote: what is the thread pitch of a daltin headstock? (Lot 4)?
| Scanned by??and confirmed virus-free. |
?
|
Dennis Turk
glenn brooks
