I hope you get this... I was not thinking...
Will WC2L
-------- Forwarded Message --------
So here is my settings:
I have not gotten this to work...
When I try to print, I see the wrong paper size!
Will WC2L
On 3/5/2016 3:24 PM, 'Dave AA6YQ'
aa6yq@...
[dxlab] wrote:
The screen shot in
Shows typical settings for printing cards "4 up". As a starting point, select a paper size that is larger than what's needed in both dimensions.
73,
Dave, AA6YQ
-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 3:17 PM
To: dxlab@...
Subject: Re: [dxlab] QSL Labels or Cards
That fixes the label. I thought had checked it. I also tried it in the printer.
Now to figure out how to print on cards.
Will WC2L
On 3/5/2016 3:05 PM, 'Dave AA6YQ' aa6yq@... [dxlab] wrote:
Did you change the setting in the ¡°Single Label Orientation¡± panel as suggested?
73,
Dave, AA6YQ
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 2:57 PM
To: dxlab@...
Subject: Re: [dxlab] QSL Labels or Cards
SO with Single label selected.
Printer set to Landscape or Portrait Printing If I set it for Height
1.1 and Width 3.2 I get "Specified column 1 offset is too larg (maximum is -2.203472 inches)" The view is still wrong. It shows the printing as horizontal. The label is shown as vertical.
If I set it for Height 3.2 and Width 1.1 I get I don't get a message. The view is still wrong. It shows the printing as horizontal. The label is shown as vertical.
SO no matter how I set it up, it fails to print correctly.
Select QSL Card:
I found a driver that seems to appear to work in other programs and gives me the QSL Card as an option. Card is setup as Width 3.5 Height 5.5. I have the printer selected, the sized selected and source selected in QSL configuration - Printer.
I have Printer QSL Cards and preview checked, I get "Specified QSL Card width is too small" essage. When the preview starts up, it Width at 10.653 x Length 8.152.
Since I can't get the DXKeeper to print labels correctly, I am guessing cards are going to be the same issue....
Will WC2L
On 3/5/2016 12:54 PM, 'Dave AA6YQ' aa6yq@... [dxlab] wrote:
AA6YQ comments below
-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, March 05, 2016 12:31 PM
To: ' Dave AA6YQ' aa6yq@... [dxlab]
Subject: [dxlab] QSL Labels or Cards
I was trying to get a few cards and or labels done.
When I preview a single label, it always shows the printing as horizontal. The label is shown as vertical. The printer is a Dymo LabelWriter 450.
In the "QSL labels and address labels" panel on the "QSL Configuration" window's Printer tab, change the setting in the "Single- Label Orientation" sub-panel.
I don't see the Avery 4150 as an option (labels I have).
That's a function of your printer driver.
With printing directly on the cards, it does not see the custom paper type I have added to the print engine.
That's a function of your printer driver.
If I select 3x5, all I get is different error messages depending on what I choose. I am using a Brother HL-5250dn.
Without knowing what the error messages say, one can only guess: try selecting a larger paper size.
73,
Dave, AA6YQ
------------------------------------
Posted by: "Dave AA6YQ"
------------------------------------
------------------------------------
Yahoo Groups Links
--
William Liporace WC2L
or AR-Cluster Node telent dxc.wc22l.com or 144.93 MHz wc2l@...
------------------------------------
Posted by: William Liporace
------------------------------------
------------------------------------
Yahoo Groups Links
------------------------------------
Posted by: "Dave AA6YQ"
------------------------------------
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
(Yahoo! ID required)
<*> To change settings via email:
dxlab-digest@...
dxlab-fullfeatured@...
<*> To unsubscribe from this group, send an email to:
dxlab-unsubscribe@...
<*> Your use of Yahoo Groups is subject to:
--
William Liporace WC2L
or
AR-Cluster Node telent dxc.wc22l.com or 144.93 MHz
wc2l@...
William WC2L