开云体育

I have seen several reports that stored RV-75's have reported Function Switches that are frozen. In my purchase of a NIB RV-75 and having the Function Switch seized, I decided to look into it after

The insert is not lead but... Have you lost the spring piece inside?? They shouldn't have play.? Every one I have seen is actually really tight, hard to get loose to remove the cage. They probably

*Today we had 46 check-ins to the net held on 7.238. The following equipment was used to check-in. * *TR3-1* *TR4(x) - 8* *TR5 - 1* *TR7 - 10* *TWINS - 13* *Next week BIll W9MXQ will be the net

What suggestions does the group have on the best way to resolve slop and play apparently caused by wear and tear on the lead inserts in the shaft couplers on the Plate & Load controls? This happens to

Jim.. I am sorry…We cannot allow your C line to sell here…it is too nice! J Bet it will be hard to part with it when it sells. I’d get it in a heartbeat, but already have a full C line with all

According to the QST article, 24 pins. Two 10-pin and one 4-pin were called out, but other combinations have been used. Another note on the QST article, you don't actually need the 100K resistors if

Complete, working C-line for sale. I am the only owner. No mods. R4C includes all filters and 4NB noise blanker. Includes Drake cables and original boxes with packing materials and manuals. $1500 cash

OK. I was unable to find what I was charging for the cable years ago.? It was most likely 10 cents an inch.? I sold it by the inch as I was getting all kinds of odd lengths.? I will sell off what I

Actually, I would need enough to populate 2 boards. I'm not sure how many the boards take. 73, Clint, VE3CMQ

I’d be interested in 2 of them. Thanks and 73, Clint, VE3CMQ Sent: Sunday, 4 February 2024 11:16 To: [email protected] Subject: Re: [DRAKE-RADIO] Searching for AUX-7 boards… I have a bag of

I still have a partial roll of the Belden 8421 left.? The original length of the injection cable was 38" TIP to TIP.? I haven't sold any in a long time and forgot what I was charging for it plus the

Confirms it many times. :D Here is the original source. /g/DRAKE-RADIO/message/28549 73 -Jim NU0C "VE7PS" <ve7ps@...> wrote: -- 73 -Jim NU0C

Yes, they do still carry them under different part numbers. Look for Molex KK series 156. Here is one example: https://www.mouser.com/ProductDetail/Molex/09-48-1084?qs=qDyi%252BDzW2VO0JexKcHUTJA%3D%3D

I think I fingered out. I now have my 2 mostly used freq's programmed. It has been many years since using BCD, but I am definitely relearning now.? Thanks for the pointing me in the right direction.

That is correct. Rob, NC0B

Paul: A quick search of the group posts confirms Belden #8421. 73 Peter VE7PS

Excuse the interruption. Elderly mind forgot---was the cable recommended for 4 line injection cable Belden 8421? Or something different? Thanks Paul K0UYA

I have a bag of the Molex edge connectors used in the TR-7/R7 if anyone is interested. Looks like Mouser no longer carries them. Dale W4OP

It's really not that hard but I can see how someone can feel intimidated if they have never worked with BCD before. Binary Coded Decimal. Each of our base-10 digits 0 through 9 is encoded as its 4-bit

Bob: You are correct....the manual is a nightmare, especially for those of us not familiar with programming BCD switches. I also believe there is an error in the manual in one of the mathematical