开云体育

Thanks Tim. It was a noninductive load in an IFR-1200S service monitor. 73 Jay yahoo.com_at_groups.io_lastradioman@...> wrote:

I suggest going over the RF and mixer stage adjustments. I am going more by experience with a T4XB but they are not much different from the C. It is normal for the power output to be slightly lower on

Jay I'd say all is normal or close to it other than 3550. Now was that into a 50 ohm? nonrestrictive load? Nothing to be concerned about actually no one will tell the difference on the receive end.

Group, While making a cheat sheet for pre-tuning my T4XC (see attached excel doc), I noticed low power out on some frequencies - especially 3550 Khz. What is normal power output on the traditional &

This is a long-shot. Try adjusting T1. Steve Wedge, W1ES Time flies like an arrow. Fruit flies like a banana. Sent with [Proton Mail](https://proton.me/mail/home) secure email.

Yes, I have tried switching the Xtals all around. I first put the 28.0 Xtal in the 29.1 slot and got nothing, no receive. I then put the 28.5 Xtal in 29.1 and got the same, nothing. Then I put the

Good point. I’d find a way of using the slots. I don’t mind using the Hayseed kits for sets that I’m keeping. I am, however, beginning to use my Sprague TO-6 to test the caps after I unhook the

That was me and thank you! Bill N1WL ?? William Losefsky? ????????? CallSend SMSAdd to SkypeYou'll need Skype CreditFree via Skype

I'm planning to use a bit of silicone and a soldered ground. John K5MO [email protected]> wrote:

I saw that small PC board with individual radial lead capacitor kit available on eBay but after studying the PC board it appeared that 2 holes needed to be drilled in the 2B chassis. While I'm sure

Thanks to all for the documents! 73, Steve Wedge, W1ES Time flies like an arrow. Fruit flies like a banana. Sent from [Proton Mail](https://proton.me/mail/home) for iOS

With the 2nd diode installed (rvs connected pair).....the pair? ensures the B-? ?can't wander more than? +/-? .7 vdc? ?from chassis potential.? ?In the old days, something like a 10 ohm

Steve, have you already seen and checked this piece of information regarding building an interconnection cable between Drake TR7 and R7: https://www.dl7maj.de/TR7-R7-cable.pdf Best regards. Karl,

Yes, if you are willing to build you own. An example of the control cable has already been posted to this thread. FWIW I used low capacitance coax for the PTO and 40MHz reference signals but RG-174 or

I think someone was having problems with two of the 10M bands with a 4-line rig recently. I happened to see these and thought I'd pass the ad along:

Thank you, Jim. This weekend while using the TR7/PS7 in the NA QSO Party, the PS7 tripped out a couple of times. I went back in this evening and recalibrated the overcurrent setting based on your

Steve, The attached is the cable that you can build. It is what I am using for my R7 / TR7 transceive 73 Dale AF7WH Sent: Sunday, January 19, 2025 2:13 PM To: [email protected] Subject:

Folks — I have someone asking me to get their R7 to work with a TR7. I just want to make sure that the connectors and cables are still obtainable. Any insights into this? Steve Wedge, W1ES Time

I meant replace with DIN connector. That looks pretty old-school with a metal plug.

I've got a 2B to recap, and I agree....? with the Qmultiplier? it's a fantastic vintage CW rig.? I pair mine with the flavor of the day CW rig and it's perfect for that. I found those capacitor