开云体育

Hi Paul, I am sure you know this, but I will state it anyway- the power out of the radio is rated into a 50 ohm load. If you are not using a dummy load to determine your output power, you are probably

Another matter to consider, in fact one of the most important, is the cable(s) used to connect raio to bird to load. I have seen apparent loss of power due to cables / connectors.

I suppose one other question is What DC voltage are you providing the radio? 12.0 V, 12.6 V, or 13.8 V? The radio is specified at 13.8 V. All of my questions might not make any difference, but it

Just curious... What sort of load are you going into? What type of connectors on the Bird and load? Are you measuring any reflected power from the load? Arnold KQ6DI

I have four ID-1 radios and since I have purchased a Bird 10K 10watt, 1.1 to 1.6 Ghz slug, I have found the high power output to range from 3 to 6 watts on each radio.(not even advertised power). I

Gee Evans... Where is that Hooter's car wash exactly? I would be willing to drive a good distance to test antenna performance there... Thanks.Joe / W8SS / Mesh Engineering / 810-629-5500 AKA: Dr. Joe

http://www.wa5vjb.com/references.html There is a 1200 MHz mobile antenna project listed here that is pretty easy to build. I've been running one on the local 1200 MHz repeaters for nearly 15 years.

http://dstargw.kd4efm.org/la_23cm_nmo_1.jpg Here is what my 3dBi looks like... Evans F. Mitchell KD4EFM _____ From: D-STAR_23cm@... [mailto:D-STAR_23cm@...] On Behalf Of Dr.

Joe, this is a HA HA HA reply..... A 1/4 wave would be best! I have a 3dBi Larsen Antenna from years past that works just great... but I have to ask in this day in age, what kind of a car wash would

G'day Joe, I didn't think too many antennas would like nice after going through a car wash :-) I'm using a Diamond SG9500N but I'm not keen to test it on the local car wash for you though...! Cheers,

What is the BEST mobile antenna for 1.2G that will go through a car wash? What's your opinion??? Thanks.Joe / W8SS / Mesh Engineering / Trustee & Sysop on D-Star for K8LCD AKA: Dr. Joe Mesh, D.M.D.,

D-Star <-> Analog... it's in the D-Star spec... Posted by: "michaelcarey69" michaelcarey@... michaelcarey69 Date: Fri Oct 15, 2010 12:56 am ((PDT)) Hi Everybody, I'm not sure if this is

Hi, Check out my videos showing the prototype ID-RP2C interface in operation. VK5REX C is now in full operation using the equipment you see in the videos. http://www.youtube.com/watch?v=MALY_mEDp_8

Intresting we the south yorkshire repeater group are also looking in to using kendecom MR4 t/ RX units any information on the interface would be of help Ernie G4LUE look at our web site

Interesting thread below about Interfacing Kenwood Analog Repeater to Icom D-STAR Controller for Use with D-STAR. Great example of continued innovation of D-STAR technologies by incorporating non-Icom

This was a great article! I would like to do the same with a Micor. 73, Nick

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the D-STAR_23cm group. File : /D-STAR Programming/dplus and How to Use It.pdf Uploaded by

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the D-STAR_23cm group. File : /Digital Voice & Data Radios/ID-1 USB Interface Notes.pdf

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the D-STAR_23cm group. File : /High-Speed Digital Data (DD)/ID-1 Troubleshooting

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the D-STAR_23cm group. File : /D-STAR Programming/ID-1 Callsign Fields in Repeater