开云体育

#uBITX

#ubitx

SM6MOJ #53444 Two capacitors -C210 and C216- arr missing from my uBITX motherboard. Also, when I connect the board to 12V, the book says that the current drain should be 100mW. But there is no current drain att all. Can I assume that the board is fault?
Michael Shreeve All Messages By This Member #53445 I looked at the V4 schematic and the value for both of those caps is zero. This means there are no caps installed. V3 has the same lack of capacitors. So, he isn't using them.? toggle quoted message Show quoted text On Sun, Jul 1, 2018 at 11:07 AM, SM6MOJ <andrew@...> wrote: Two capacitors -C210 and C216- arr missing from my uBITX motherboard. Also, when I connect the board to 12V, the book says that the current drain should be 100mW. But there is no current drain att all. Can I assume that the board is fault? -- Michael Shreeve N6GRG
Michael Shreeve All Messages By This Member #53446 Are you getting audio from the board ? toggle quoted message Show quoted text On Sun, Jul 1, 2018 at 11:54 AM, Michael Shreeve <shreevester@...> wrote: I looked at the V4 schematic and the value for both of those caps is zero. This means there are no caps installed. V3 has the same lack of capacitors. So, he isn't using them.? On Sun, Jul 1, 2018 at 11:07 AM, SM6MOJ <andrew@...> wrote: Two capacitors -C210 and C216- arr missing from my uBITX motherboard. Also, when I connect the board to 12V, the book says that the current drain should be 100mW. But there is no current drain att all. Can I assume that the board is fault? -- Michael Shreeve N6GRG -- Michael Shreeve N6GRG
SM6MOJ #53454 Dear Michael Thank you for your wise words. Now all I have to do is work out why there is no current drain. Andrew
Lowell Haney NE4EB All Messages By This Member #53455 If there is no current drain, what shows up on the LCD? Is the back light lit? What method are you using to measure the current draw?
SM6MOJ #54098 My uBITX is finally finished. The Hammond case was a tight fit and the knobs came from my junkbox. The manipulator is home made and the microphone is housed in an old pill box. It did not want to know about the straight key at first, so I upgraded to KD8CEC firmware. This knocked out both keys. After trying three different uBITX firmware packages and two different uBITX managers, I reverted to the default firmware. It could be that the uBITX manager and I did not agree with each other. Finally, it accepted both keys, although the straght key sounded a bit flakey until I cleaned the morse key points. 20180706_171943.jpg
Tony Frey #54118 开云体育 Which Hammond case did you use? Thanks, Tony? KE4MHP Acta non Verba ? toggle quoted message Show quoted text From: 30111237140n behalf of Sent: Thursday, July 12, 2018 11:02 AM To: [email protected] Subject: [BITX20] #uBITX ? My uBITX is finally finished. The Hammond case was a tight fit and the knobs came from my junkbox. The manipulator is home made and the microphone is housed in an old pill box. It did not want to know about the straight key at first, so I upgraded to KD8CEC firmware. This knocked out both keys. After trying three different uBITX firmware packages and two different uBITX managers, I reverted to the default firmware. It could be that the uBITX manager and I did not agree with each other. Finally, it accepted both keys, although the straght key sounded a bit flakey until I cleaned the morse key points.

Previous Topic Next Topic