开云体育

Instructions for using the Raduino v1.26 (PE1NWL) in French.

#bitx40help

F1NQP JanJack All Messages By This Member #34101 Hello. You will find the instructions for using the Raduino v1.26 from PE1NWL, translated into French on my website. So I have not yet started editing my Bitx40, but at least I have a notice in French ;-) 73 to all.
Allard PE1NWL All Messages By This Member #34102 Dear Jean-Jacques, thanks for the French translations. I noticed that on this page there are still instructions for installing the si5351 library: Installez les bibliothèques depuis le programme Arduino: Il va falloir maintenant installer les bibliothèques qui vont servir au SI5351. However these are now obsolete as the si5351 library is no longer used by the raduino sketch. So you may want to remove this section. 73 Allard PE1NWL toggle quoted message Show quoted text On Tue, October 31, 2017 13:55, F1NQP JanJack wrote: Hello. You will find the instructions for using the Raduino v1.26 from PE1NWL, translated into French on my website. ( ) So I have not yet started editing my Bitx40, but at least I have a notice in French ;-) 73 to all.
F1NQP JanJack All Messages By This Member #34103 On Tue, Oct 31, 2017 at 06:19 am, Allard PE1NWL wrote: However these are now obsolete as the si5351 library is no longer used by the raduino sketch. So you may want to remove this section. Hello Allard. No library is to install? I can delete everything related to the installation of libraries?
Allard PE1NWL All Messages By This Member #34104 Since v1.20, Jerry's minimal si5351 routines are included in the sketch code. Hence we don't need to install the si5351 library anymore. Note that the sketch still requires some other libraries (wire, eeprom, liquidcrystal) but these are already included in the IDE, so you won't need to manually download and install them. 73 Allard PE1NWL toggle quoted message Show quoted text On Tue, October 31, 2017 14:34, F1NQP JanJack wrote: On Tue, Oct 31, 2017 at 06:19 am, Allard PE1NWL wrote: However these are now obsolete as the si5351 library is no longer used by the raduino sketch. So you may want to remove this section. Hello Allard. No library is to install? I can delete everything related to the installation of libraries?
F1NQP JanJack All Messages By This Member #34105 OK i modify my article accordingly. Thanks again Alllard.
MVS Sarma All Messages By This Member #34106 hi Allard, ?I suppose that following procedure could be implementable for a possible 2 band working. ?Initially the VFO would start with 40m band with LSB and 10/12MHz BFO switchable with fine adjustment. ?As you go to end of the band , it could perhaps aumatically switch over to 20m with usb , and same selectable VFO , BUT now th LPF can be switched by a relay. There might not be any need for any extra button for band change. On e way down from 20m ?if some one continues to reduce below 14.00 , it could revert to 7MHz (40m), obviously lsb and? filter relay released for 40m? lpf. ?Thuis is wild imagination , I am nott from Software at all.Kindly study the possibility. regards ?sarma ?vu3zmv regards Sarma ? toggle quoted message Show quoted text On Tue, Oct 31, 2017 at 7:04 PM, F1NQP JanJack <f1nqp@...> wrote: On Tue, Oct 31, 2017 at 06:19 am, Allard PE1NWL wrote: However these are now obsolete as the si5351 library is no longer used by the raduino sketch. So you may want to remove this section. Hello Allard. No library is to install? I can delete everything related to the installation of libraries?
Allard PE1NWL All Messages By This Member #34108 Hi Sarma, thanks for the suggestion, I will consider your idea for auto band switching in raduino v2. However even if we offer auto band switching, I believe most ops would still want to have an additional manual switch or button. Because it allows for quick band switching without having to turn the dial all the way up or down just to switch bands. 73 Allard PE1NWL toggle quoted message Show quoted text On Tue, October 31, 2017 15:06, Mvs Sarma wrote: hi Allard, I suppose that following procedure could be implementable for a possible 2 band working. Initially the VFO would start with 40m band with LSB and 10/12MHz BFO switchable with fine adjustment. As you go to end of the band , it could perhaps aumatically switch over to 20m with usb , and same selectable VFO , BUT now th LPF can be switched by a relay. There might not be any need for any extra button for band change. On e way down from 20m if some one continues to reduce below 14.00 , it could revert to 7MHz (40m), obviously lsb and filter relay released for 40m lpf. Thuis is wild imagination , I am nott from Software at all.Kindly study the possibility. regards sarma vu3zmv regards Sarma On Tue, Oct 31, 2017 at 7:04 PM, F1NQP JanJack <f1nqp@...> wrote: On Tue, Oct 31, 2017 at 06:19 am, Allard PE1NWL wrote: However these are now obsolete as the si5351 library is no longer used by the raduino sketch. So you may want to remove this section. Hello Allard. No library is to install? I can delete everything related to the installation of libraries?

Previous Topic Next Topic