开云体育

a Little Gun Shy

#ubitx-help #ubitx

Vince N2AIE All Messages By This Member #44818 So, My uBITX is working fine, so I should just leave it alone...Of Course not.. 1.? Before I start mucking with the sketch, I want to be able to get it back to what came with the rig. so went to? downloaded the zip as usual.? Inside there is the ubitx_20 folder the .ino with the ubitx_20, is, I assume that is what should be uploaded to the nano? Is the CAT function an original part of the sketch that will get loaded with the ubitx_20..that i haven't tried to use? as I would like to have HRD control of the uBITX.. ugg.. ? Must not be thinking this through, Allard's changes on my 40 seemed to be easy enough. quick answer would be appreciated. Vince n2aie
Vince N2AIE All Messages By This Member #44819 I didn't mention, I'm just using the Arduino IDE not the Ian Lee memory manager which i cant seem to get it to read the nano (in windows) vince
Vince N2AIE All Messages By This Member #44820 also current load is v2.0 that came with the rig vince
Mike Woods All Messages By This Member #44821 开云体育 Vince The KD8CEC Memory Manager requires mods to the stock firmware or installation of Ian's firmware to work. Check out the guide at:? ? and feed back with any issues, as I want to get this right! 73 Mike On 18/03/18 9:25 AM, Vince Loschiavo wrote: I didn't mention, I'm just using the Arduino IDE not the Ian Lee memory manager which i cant seem to get it to read the nano (in windows) vince -- Mike Woods mhwoods@...
Vince N2AIE All Messages By This Member #44822 Mike, Getting this on your link. Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, webmaster@... and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. Additionally, a 500 Internal Server Error error was encountered while trying to use an ErrorDocument to handle the request.
Vince N2AIE All Messages By This Member #44823 went directly.. I'll check it out Thanks Vince
Vince N2AIE All Messages By This Member #44824 Ok. I've checked out your site before... Just was gun shy to ensure i had the farhan load.. So your steps are fine .. reloaded Farhan no problem. all good then did IanLee's version...uploaded fine now to review his site for the menu settings. Still No CAT control with HRD..;=(( vince n2aie
Vince N2AIE All Messages By This Member #44825 that was Dr. Lees v.1.04 Vince
Mike Woods All Messages By This Member #44827 开云体育 Vince Sorry you got an Internal Server Error.? These occur periodically when the server runs out of memory (i.e. whe 6000 BITX20 list members go to the website all at the same time!).? They clear within a few seconds to around a minute, and only occur every couple of days.? Sometimes they are the result of Denial of Service attempts.? Some things to check: 1) Have you checked that you are connecting to your uBITx (e.g. in the Arduino IDE)? 2) Have you selected the Hamlib FT817 as the rig and the correct port? 3) Have you the correct baud rate setting and stop bit? ??? 38400 baud 1 stop bit. I don't have HRD so can't really comment on "how" you do this! may be helpful Mike ? On 18/03/18 11:23 AM, Vince Loschiavo wrote: that was Dr. Lees v.1.04 Vince -- Mike Woods mhwoods@...
Randy All Messages By This Member #44828 Randy
Vince N2AIE All Messages By This Member #44832 so..used Xloader...loaded v0.27 all good and CAT Functioning ! Thanks Vince n2aie will post pics..been working east coast on 40 SSB.. ?
Ian Lee All Messages By This Member #44834 Vince, Mike, Randy and all Thank you Mikde and Randy. And congratulations on communicating normally with your computer. Vince Version 0.27 is a slightly older version, but it is okay.? I will release new firmware in a few days. Upgrade uBITX Manager with uBITX firmware at that time. The new firmware adds WSPR functionality and has several bug fixes and improvements.? Ian KD8CEC 2018-03-18 9:17 GMT+09:00 Vince Loschiavo <vince320@...>: toggle quoted message Show quoted text so..used Xloader...loaded v0.27 all good and CAT Functioning ! Thanks Vince n2aie will post pics..been working east coast on 40 SSB.. ? -- Best 73 KD8CEC / Ph.D ian lee kd8cec@... (my blog)
Vince N2AIE All Messages By This Member #44896 All Good today.? Once the KD8CEC software was installed, finally found a newer Memory Manager. Maybe a Link in Files here for all pertinent programs, ie. uBITX Memory Manager all recent versions that Dr. Lee would like to have up, Hexfiles in sequence. link to xloader, might give everyone that isn't a programmer a fighting chance to get upgraded to what appears to be great mods to the original software (by the way should also be there) de N2AIE Vince p.s. like the keyer ...

Previous Topic Next Topic