开云体育

I appear to have damaged the raduino board in my bitx-40. Does anyone know how I can purchase this separately? It seems impossible to email HFsigs and there is no option on their web page.

David Holland All Messages By This Member #34649 I appear to have damaged the raduino board in my bitx-40.? Does anyone know how I can purchase this separately?? It seems impossible to email HFsigs and there is no option on their web page. Dave G4LDT
David Arthur All Messages By This Member #34650 You can buy the Raduino separately: However, LCD and Arduino Nano could be replaced fairly easily.
Dexter N Muir All Messages By This Member #34651 fairly easily? How to remove old Nano without collateral damage given no hot-air gun? Hot-plate?
David Arthur All Messages By This Member #34652 I've desoldered Nanos and similar boards before. Just takes a solder sucker or wick and some patience. Coincidentally, that's why I prefer to use headers on any project where I'm attaching a board like this :)? toggle quoted message Show quoted text On Fri, Nov 17, 2017 at 5:47 PM Dexter N Muir <dexy@...> wrote: fairly easily? How to remove old Nano without collateral damage given no hot-air gun? Hot-plate?
Vince Vielhaber #34653 experience. Vince. toggle quoted message Show quoted text On 11/17/2017 05:47 PM, Dexter N Muir wrote: fairly easily? How to remove old Nano without collateral damage given no hot-air gun? Hot-plate? -- Michigan VHF Corp.
Thomas Sharka All Messages By This Member #34654 If you don't care about the old nano board, how about carefully cutting it out of the board and removing the pins one by one? ? Sent from Yahoo Mail. On Friday, November 17, 2017 6:42 PM, Vince Vielhaber <vev@...> wrote: experience. Vince. toggle quoted message Show quoted text On 11/17/2017 05:47 PM, Dexter N Muir wrote: > fairly easily? How to remove old Nano without collateral damage given > no hot-air gun? Hot-plate? -- ? Michigan VHF Corp.? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
Kelly Jack All Messages By This Member #34655 Can confirm this is doable. I fried my nano and cut it out using side cutters. ?I cut about four pins on each side then broke that piece of the nano board off. And so on. then desoldered pins one by one.
Michael Hagen All Messages By This Member #34656 开云体育 Yes!? I have an improved version with lots of extras. So called RaduinoX. Bare PCB or complete and tested. Ask the dozen or so folks who bought them. ? For those wanting a Raduino board. There is a better option than the orginal Raduino board with it Soldered - in Nano. RaduinoX? PCB designed to add some features. I have Lots of Bare PCBs and some assembled and tested.? Lots of Bare PCBS! Several sold to guys in this group. I used this board, LCD, and Rotary Encoder to make a nice dedicated RF signal generator. 1) I wanted to be able to plug Nano in and out, not soldered. I wanted the USB connect next to the side of the cabinet so I can program without taking the lid off.? I will make a small hole. 2) Added, diode protection, more filtering and conditioning on the power input.? Regulator is bolted down. 3) Added a dedicated connector for Rotary Encoder with pullups and bounce capacitors. 4) Added an I2C connector. 5) I wanted proper Level Shifting to the Si 3V part.? Added FETs and pullups for that. 6) Added D0 and D1 pins on PCB. 7) Kept power and VFO connector on 5P header so no changes to my present wiring was necessary. 8) Put contrast Pot where you can get to it. 9) Complete documentation. 10) Fits original LCD perfectly. Take a look if you are interested. motdog@verizon dot net Mike, WA6ISP On 11/17/2017 1:50 PM, David Holland wrote: I appear to have damaged the raduino board in my bitx-40.? Does anyone know how I can purchase this separately?? It seems impossible to email HFsigs and there is no option on their web page. Dave G4LDT -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..." Mike@...
James Lawrie All Messages By This Member #34690 开云体育 Tried the link you posted but didn't work. I would be interested in your PCBs. Thanks, Jim Get Outlook for Android toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of Michael Hagen <motdog@...> Sent: Friday, November 17, 2017 6:07:14 PM To: [email protected] Subject: Re: [BITX20] I appear to have damaged the raduino board in my bitx-40. Does anyone know how I can purchase this separately? It seems impossible to email HFsigs and there is no option on their web page. ? Yes!? I have an improved version with lots of extras. So called RaduinoX. Bare PCB or complete and tested. Ask the dozen or so folks who bought them. ? For those wanting a Raduino board. There is a better option than the orginal Raduino board with it Soldered - in Nano. RaduinoX? PCB designed to add some features. I have Lots of Bare PCBs and some assembled and tested.? Lots of Bare PCBS! Several sold to guys in this group. I used this board, LCD, and Rotary Encoder to make a nice dedicated RF signal generator. 1) I wanted to be able to plug Nano in and out, not soldered. I wanted the USB connect next to the side of the cabinet so I can program without taking the lid off.? I will make a small hole. 2) Added, diode protection, more filtering and conditioning on the power input.? Regulator is bolted down. 3) Added a dedicated connector for Rotary Encoder with pullups and bounce capacitors. 4) Added an I2C connector. 5) I wanted proper Level Shifting to the Si 3V part.? Added FETs and pullups for that. 6) Added D0 and D1 pins on PCB. 7) Kept power and VFO connector on 5P header so no changes to my present wiring was necessary. 8) Put contrast Pot where you can get to it. 9) Complete documentation. 10) Fits original LCD perfectly. Take a look if you are interested. motdog@verizon dot net Mike, WA6ISP On 11/17/2017 1:50 PM, David Holland wrote: I appear to have damaged the raduino board in my bitx-40.? Does anyone know how I can purchase this separately?? It seems impossible to email HFsigs and there is no option on their web page. Dave G4LDT -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..." Mike@...
Jerry Gaffke All Messages By This Member #34691 Not sure why you can't buy a Raduino from hfsigs.com if that's what you want. Near the bottom of the buy page: ?? you should see this text: ######################## Buy the Raduino for $25 with free shipping ($10 extra for DHL Shipping) The Raduino is a general purpose, programmable board that can be used as a VFO, controller, in your radio projects. It comes bundled with the BITX40 kit. This is an option for those who wish to use the Raduinio in other projects Box Contents 1 x Raduino board 1 x 5-pin connector pair (for attaching the Raduino to the BITX and power supply) 1 x 8-pin connector pair (for attaching the Raduino to the front ) 8 x Half-inch brass stand-offs 8 x M3 mounting bolts screws 4 x M3 mounting nuts 1 x 10k linear pot (Tuning)
Dexter N Muir All Messages By This Member #34692 If it's Mike's PCBs you're looking for then yes, of course the link he gives won't work. It's not a link to a website, it's a deliberately-mangled (to foil spam-bots' harvesting) email address, so replace "at " with "." and email him. I just did, flawlessly and with prompt reply - good one Mike! 73 de ZL2DEX
Michael Hagen All Messages By This Member #34693 开云体育 ? Much better than Raduino. Alternate PCB is RaduinoX. ? Bare PCB is $10, includes shipping and PayPal. Assembled PCB is $38,? includes shipping and $2 for PayPal = $40. New Nano, Plugs into sockets add $4. New LCD, just like original, Yellow 2X16 add $5. 3D Printed Bezel Kit, includes Hardware add $4. So let me know what you want and if you need more Info? Shipping to Foreign is probably? about $14, 3x4x2" Box. Thanks Mike, WA6ISP motdog@... On 11/18/2017 4:58 PM, Jerry Gaffke via Groups.Io wrote: Not sure why you can't buy a Raduino from hfsigs.com if that's what you want. Near the bottom of the buy page: ?? you should see this text: ######################## Buy the Raduino for $25 with free shipping ($10 extra for DHL Shipping) The Raduino is a general purpose, programmable board that can be used as a VFO, controller, in your radio projects. It comes bundled with the BITX40 kit. This is an option for those who wish to use the Raduinio in other projects Box Contents 1 x Raduino board 1 x 5-pin connector pair (for attaching the Raduino to the BITX and power supply) 1 x 8-pin connector pair (for attaching the Raduino to the front ) 8 x Half-inch brass stand-offs 8 x M3 mounting bolts screws 4 x M3 mounting nuts 1 x 10k linear pot (Tuning) -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..." Mike@...
Michael Hagen All Messages By This Member #34694 开云体育 On 11/18/2017 5:16 PM, Michael Hagen wrote: ? Much better than Raduino. Alternate PCB is RaduinoX. ? Bare PCB is $10, includes shipping and PayPal. Assembled PCB is $38,? includes shipping and $2 for PayPal = $40. New Nano, Plugs into sockets add $4. New LCD, just like original, Yellow 2X16 add $5. 3D Printed Bezel Kit, includes Hardware add $4. So let me know what you want and if you need more Info? Shipping to Foreign is probably? about $14, 3x4x2" Box. Thanks Mike, WA6ISP motdog@... On 11/18/2017 4:58 PM, Jerry Gaffke via Groups.Io wrote: Not sure why you can't buy a Raduino from hfsigs.com if that's what you want. Near the bottom of the buy page: ?? you should see this text: ######################## Buy the Raduino for $25 with free shipping ($10 extra for DHL Shipping) The Raduino is a general purpose, programmable board that can be used as a VFO, controller, in your radio projects. It comes bundled with the BITX40 kit. This is an option for those who wish to use the Raduinio in other projects Box Contents 1 x Raduino board 1 x 5-pin connector pair (for attaching the Raduino to the BITX and power supply) 1 x 8-pin connector pair (for attaching the Raduino to the front ) 8 x Half-inch brass stand-offs 8 x M3 mounting bolts screws 4 x M3 mounting nuts 1 x 10k linear pot (Tuning) -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..." Mike@... -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..." Mike@... RaduinoX7ASch.pdf RaduinoX7ASch.pdf RaduinoX7bot.pdf RaduinoX7bot.pdf RaduinoX7top.pdf RaduinoX7top.pdf RaduinoXBOM.pdf RaduinoXBOM.pdf RaduinoXConnect.pdf RaduinoXConnect.pdf
Dexter N Muir All Messages By This Member #34695 Further comment, Jim - and anyone else - Spam-bots can't decipher ASCII-Art. I replace the 'd' of my address with "[)". Put that into a Courier font (standard in a text-editor) and you'll see a capital-d. "/-\" for A, "][" for I ... the young'uns get it - they use it extensively.
James Lawrie All Messages By This Member #34708 开云体育 Hello, Thanks thought it was a web page instead. Jim Sent from my Galaxy Tab A toggle quoted message Show quoted text -------- Original message -------- From: Dexter N Muir <dexy@...> Date: 11/18/17 19:26 (GMT-06:00) To: [email protected] Subject: Re: [BITX20] I appear to have damaged the raduino board in my bitx-40. Does anyone know how I can purchase this separately? It seems impossible to email HFsigs and there is no option on their web page. Further comment, Jim - and anyone else - Spam-bots can't decipher ASCII-Art. I replace the 'd' of my address with "[)". Put that into a Courier font (standard in a text-editor) and you'll see a capital-d. "/-\" for A, "][" for I ... the young'uns get it - they use it extensively.

Previous Topic Next Topic