开云体育

Nick, That's good as then there are two like this.? ?I'm testing mine.?? I have one report of the MPSH10s might be a bit tepid in their power handling. The might work for the predriver and not

Hi Allison, thanks. My little proto board is from Q90 to the FET pre drivers. See below, the PCB on left side. OK on the -10dBm level. Will use that in any future testing, once i get the 2N4427's etc

I think they might work.? If you got them smoke them (hopefully not).? I don't have enough 5109s or 4427s to try. Allison

First off the output of the mixer is anywhere near -6dbm its going to be distorted. I'd expect -10dbm max. The mpsh10s I have not tried as they have not arrived.? I'd expect to have to pair them up

SS9018, use what every you want.? Its power capability is the pits but for Q90 its ok. We have been through this one once before. For the driver you need a part that can peak around .6A. Allison

I came across an old '80s project box with a circuit board and lcd display perfect for the ubitx... However I am finding very little documentation on the SEIKO M4032 LCD display... Any information or

I've sent the paypal account money for 1 of each. In case the address didn't make it: *Ron Herring**W7HD** **10270 W Mars Rd** **Tucson, AZ 85743** * -- Ron W7HD - NAQCC#7587 OMISS#9898 KX3#6966

That is a much more elegant way of doing what I was thinking with duct tape and bailing wire. http://ubitx.net/2018/03/22/drive-control-2-methods/ Looks like the problem wasn't the idea but my

Allison, what i am seeing in my 'proto' build of driver stages only, using MPSH10's, is a flat response within 1dB BUT that's with relatively low drive levels using the Rigol at -20dBm input. If I up

I agree that setting the IDE set up to compile and program can be tricky, but once you get a good setup, it works just as smoothly as native Arduino parts. The Pill? I'm using seems to have a Maple

Would the 2n5109 work in all the stages or is the 1W dissapation a problem? tim ab0wr "ajparent1/KB1GMX" <kb1gmx@...> wrote:

Hi Kees, a query/suggestion on your DX postage: Here in Aus I can use a DL envelope to a thickness of 5mm, just sent as an Airmail letter. I have been using this method for my VK4PLN boards to send

Also, what about these for the drivers? SS9018 RF NPN 15v 50mA 1.1GHz ( http://www.minikits.com.au/SS9018?search=2N5770 ) 73.

Relay switching of RV1 is on the ubitx.net ( http://ubitx.net ) website.? *Dr.?* *William J. Schmidt - K9HZ *

Calling CQ bitx on 7.277, Heard VE3THR earlier. I will be here trying for a while.

You results so far are in agreement with what Glenn VK3PE has found, see his posts: /g/BITX20/message/44289 Great work. Ill be keen to see how you go with the MPSH10/MMBTH10 in the

I am experimenting with replacing RV1 with a 31dB, RF step attenuator board from SV1AFN.?https://www.sv1afn.com/rfattenuator.html

No go on the brown wire. I also tried 4 letter words and crying. Moving on to whiskey until the nano gets here. Thanks for the suggestion tho

Ok Kees Many Thanks.

Gilles, The total price for 2 kits sent to France is $18.30 ($4.30 for the 2 kits plus $14.00 postage) 73 Kees K5BCQ