开云体育

Hi Doug, As they say, a picture is worth a thousand words:) When they said that they didn't have video <sly grin>. Good job. 73, Bill KU8H -- bark less - wag more

these are the ?BITX parts.? same mic for BITX40. -- www.bitxmap.com ( http://www.bitxmap.com )

Gentlemen, Out of consideration for the original intent of my BITeensio thread, would you please take this microscope and magnification discussion to a new thread?? The original intent was to

Bill & Mike--- the mic looks much like a pencil -eraser end with 2 solder blobs on one end, black felt on the other.. That's the end you talk into.. The encoder is less than a postage stamp square,

I've got one. I'll get back with more details later today. Roy WA0YMH [email protected]> wrote:

Got it; Like howard said, I will pick it up with tweezers and go vertical vs T-P.

Has anyone tried this type of scope: (eBay 352344602558)? For $60, I'd be very interested if it works. Jack, W8TEE

Alison : Doesn't it kill the CW Sidetone with your mute connected to VOL-H ? Ashar has his V4 pop circuit connected at M2(R70) with the value of R70 increased to 1K ohms. ?I think that this option

I just received a uBITX yesterday and I'm a total noob at this. I have a small cylinder about 1 cm in diameter and 1 cm high. Is that the electret mic? If not what is it? I do have a small rectangular

It is exciting!?? It would be great if Sunil of?amateurradiokits.in could create a "deluxe" case with a cutout for the Nextion and either room or cutouts for additional switches and pots, e.g. an

I ordered a 3.2 enhanced from ITEAD on their website. Then I looked around AliExpress and Ebay just to see the knock-offs. Funny, no particularly compelling savings (most actually more expensive) and

Good Mike, To make it ultra neat: solder back the diode and cut the track inbetween the diodes. Solder a fixed resistor between the cut track (you need to scrape it but a resistor may fit between the

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* UBITX CASE MANUAL PCB FRONT PANEL.pdf *Uploaded By:*

Did the biasing mod. That solved the crossover distortion issue. I took a 500 ohm pot and paralleled that with a 125ohm resistor. The mod doesn't look so good? (LOL) but it works. One of the

John The general rule of thumb is to connect the negative end of the capacitor to the circuit that goes to earth (perhaps via a resistor). In the circuit here:?? http://ubitx.net/new-feature-agc/ C2

Hello,? I have downloaded the MAX 9814 AGC circuit courtesy of the uBitx site but? note that no polarities are shown for the? 10uF Capacitors C4, & C6. Can anyone help here please? Thank you.

Mike, Try this: Lift up D15 or 16 diconnecting one end from the board. Solder the center and one end of a 47 ot 100 Ohm preset between the two diodes. Make sure the preset is at minimum. Power up and

To my dear XYL's chagrin, I have just purchased a stereo AmScope SE400-X microscope with fixed 5x or 10x magnifications (depending upon the eyepice selected).? This has a 9 inch distance to the work

Just have fun with it. It's not a $1000 investment (although I wish my Yaesu could receive this well) Here's a pic of my 1st build. As you can see . . . no metal . . just a cardboard box.

The voltages seem fine to me. I dont have my board with me here at the farm, I will have to get back after a week to check my boards! Raj