开云体育

Hello all, We’ve received over forty score sheets so far, and really appreciate the level of participation this year. If you have not yet emailed your score sheet, please do so as we plan to post

Hi Ian, Please contact me, I would like your AGC you do not want. Thanks Scott

It would help those on this board to know if you have the Full kit or the Basic kit without the case. If the full kit, be sure you have plugged in the correct connectors.? There are a couple that

I just received my ubitx v6 full kil and as everyone has said, it took me approx 1 hour to put it together. I plugged in my 12 volt 3 amp power supply and had the following problems. I need some

Hi all, Hope youre keeping well,i have a bitx 40 working with ssb and cw. comes with PE1 NWL 1,.29 FIRMWARE. its housed in a unmarked really nice blue case. comes with microphone and power lead.

I’m doing something similar with my v5. I use SDR-Console software with an RTL-SDR. ?It uses OmniRig to manage the CAT control. OmniRig has settings to change offsets for the different modes.

Have my assembled and aligned V6? with original 6.1.? No mods.? Made several CW contacts with it.? Never going to get around to making any improvements.? $175 Paypal.? Includes shipping anywhere

Thanks Jason, Yeah those are nice videos. I have not seen his Youtube page before. 72 Aaron K5ATG K5ATG Blog Sent: Tuesday, April 7, 2020 11:06 AM To: [email protected] Subject: Re: [BITX20] BITX 14MHz

Thanks Mark, Like I said, I’m a newbie so I will start identifying the VFO, BFO and AF amp and PA. 72 Aaron K5ATG K5ATG Blog Sent: Tuesday, April 7, 2020 11:09 AM To: [email protected] Subject: Re:

Thanks Nigel for helping me understand more about audio levels? and how having a power meter will help me get those correct! And thanks for the others who suggested getting the cheap cb power/swr

Buy a cheap CB SWR meter for $25 on Amazon Hamfest they go for $10 but everything is shut down

Nobody mentioned setting the audio levels? Set the speaker audio to a very low level and watch the power out on a power meter (you really ought to get one) step it up a level at a time until you get

I have a V3 ubitx. I have added the I.F (45Mhz) 50Mhz buffer board (https://ubitx.net/2018/07/21/full-sdr-receive-with-g4hup-buffer-amp/) and taken this to an SDRplay RSP1A. I have added a USB hub and

A few months ago I tested a nice 10.7 Mhz crystal filter I bought years ago. Most likely I did damage it with a 7dbm dds, but I cannot remember exactly. Testing using an attenuator and Antuino in SNA

The height is probably fine.? Is your antenna working, probably not well. I am using an efhw that is 10' high at one end and 20' at the other end. I have made phone contacts into eastern europe on my

Evan, Ok, tks. 73 de Rubens py2pvb -- Sauda??es fraternais, 73/51 PY2PVB Rubens Kamimura Tel. (18) 3746-8680 ramal 116 Cel. (18) 9-9819-2225 WhatsApp ou (18) 9-9819-2255 Em ter., 7 de abr. de 2020

Tks -- Sauda??es fraternais, 73/51 PY2PVB Rubens Kamimura Tel. (18) 3746-8680 ramal 116 Cel. (18) 9-9819-2225 WhatsApp ou (18) 9-9819-2255 Em ter., 7 de abr. de 2020 às 14:19, Evan Hand

I use the HF Signals direction: https://www.hfsignals.com/index.php/ubitx-tuneup/ Requires an amp meter in the power to the finals, or just look for a difference of 100 ma for each setting. 73 Evan

Rubens, Most likely it was heat that fried your finals.? Digital modes have been reported to have this issue on all of the uBiTx models, as they keep the transmitter on for 15 seconds at a time at

ALL I have uBITX v4 and use it only for FT8 in 40m, but the IRF510 outputs are burned, I am changing them, how do I check if the bias and power settings are correct? a) I check the tension in the GATE