开云体育

When I see a 50 ohm BNC receptacle that is unreliable its likely because someone plugged in a 75 ohm into it and sometime verse visa. They have different plastic sizing and the center pin and socket

Some may not be aware that if you remove the locking ring from a BNC male connector, it will plug into an N connector. Shops sometimes make quick-connect jumpers this way.

Tim, I see your kit for uBitX! It looks like I can install it on my v5; not too hard. ?Do I understand correctly that it can be wired to drive the SMeter In the faceplate of my inkits case? If so are

Hi Dave, There are a bunch of off shore connectors out there that are just a mess. If you stick with named connectors- Amphenol, Connex etc, the center pin spreading is not an issue. I also use

I have gotten rid of all the BNC connectors. The center pin of a bnc female has tendency to become un reliable.? Perhaps no one else has had this problem. -- 73 Dave ADOB (

Dick, This picture with ports labeled might be of use in the future. Enjoy the rig! 73 Evan AC9TU

Hi Lee, All of the code is on github. https://github.com/reedbn/ubitxv6 Reed

Thank You so much. Dick Sent from Mail for Windows 10 Sent: Tuesday, July 7, 2020 7:57 PM To: [email protected] Subject: Re: [BITX20] Bitx 20 front panel Dick on the v6 from left to right is mic,

Dick on the v6 from left to right is mic, phones, CW key. Barry

Hi Evan, This is the uBitx version 6 touch screen. Thanks Dick Sent from Mail for Windows 10 Sent: Tuesday, July 7, 2020 7:24 PM To: [email protected] Subject: Re: [BITX20] Bitx 20 front panel Dick, To

Forgot to answer the fuse question. For the uBITX series, the 3 amp fuse would be correct.? Since the BITX20 has only a single IFR510 as the PA, I would assume that the current requirements would be

Dick, To be clear, do you have a uBITX version 6 with the touch screen or a BITX20 which was a single band 20-meter radio?? It does make a huge differance.? The model should be printed on the

Is there a new version is R1.5.0 and if so where can it be downloaded? Thank you for all the hard work. -- Lee - N9LO "I Void Warranties"

Hi Folks, Just finished my first attempt at the Bitx 20 today.??? At the risk of appearing stupid, but I need to make sure before I put power to the unit.?? If were looking at the front panel the

Forget the question I asked.... I found it..... what was making it hard was the amount of time I had to hold the encoder in.? I also read (since? this question has been asked several times) to hold

OK, now that I got the mic cable fixed, I am on to checking the power out.? I would like to use mic and the CW selection.? Where I am at now is when I push the mic button with CW on I get a dot dot

Hi all, I have the amateuradiokits case which has its own front panel pcb the audio1 header on the v6 connects into this which in turn connects to the external audio amp supplied with the case. In

I have had a few work loose and bnc's are the worst because you have to take the enclosure apart to reach inside to hold the backside of the connector to get the cable loose. Fuse holders are the

I do use lock washers on controls/connectors, like the amatuer radio kits enclosure has all round holes so there is no choice. No big deal, I don't fret about it. It's just that Marshall had such an

Hi Allison, I have seen a couple of them in soft aluminum that were mounted in a round hole. I don't who installed them but they worked loose withe repeated plug/unplug cycles. They would turn in the