开云体育

Arrow has 7500 parts of the si5351a-b02382-gtr, minimum order of 2500 https://www.arrow.com/en/products/si5351a-b02382-gtr/silicon-labs Can't find a datasheet addendum, but again, our only needed

The good news is that Mouser has 30000 of the Si5351A-B ordered. Bad news:? They are scheduled to arrive Christmas week of 2021:

Sounds like some ubitx should be available now. Don't? panic. Automobile factories are in dire straights, except in Korea where they have ample supply for their vehicles. Hang in there, we have

Are the ubitx v6 kits in stock? I want to order a kit plus a extra chassis. I sent an emil to hfkits? 73 Mije N2MS

How 'bout that! I was a serious stamp collector at one time and had a magnifying headset that I used for "fly-specking" stamps. Now I use it for SMD stuff! Jack, W8TEE

Every body seems to be suffering from this shortage it seems. In regards to the si5351, there now exists a pin and software compatible chinese clone the ms5351. Reportedly some nanovna clones now have

people, I wanted you to hear it here first. there is a global shortage of chips. they are saying it is a due to a double whammy - covid shutdown hit the semiconductor fabs and a huge pressure on them

Hello Jack, Yeah, that’s what I do. First I weld a leg, then I can rotate. For a start I am not dissatisfied with my learning I placed 12 transistors in 1H15 or 1 every 6 mms. That’s the most

I think Evan and Gary are right, concentrate on figuring out why the Nano does not talk to the Nextion. Gary's point about the CH340 chip's 3.3v regulator in particular, check that first. The Si5351

Check that you have 3.3V on the Nano output pin with everything installed as it is. (simple first thing to do) Also check the voltage level on the reset pin of the Nano. Last time(s) this failure

Gerard: FWIW: I find it a lot easier to tin the pads first. Then use a "hook tweeser": to hold it in place (much like the inset picture with the quarter) while I touch one end with the iron. This will

Hello to all, As I wait for parts to repair my spectrum analyzer, I start something else. This day I just welded my first surface component on my PCB that I imagined. It’s not easy, it’s the first

Chris, Read through this thread: /g/BITX20/message/83186 What I have done is installed the back-to-back 1n4148 diodes on the K1 relay per the picture. 73 Evan AC9TU

Try replacing the Nano. My guess is that the EEPROM has worn out. While the original (Italian) Nano's would handle hundreds of thousands of writes, some of the clone Nano's will fail after only 10000

Don, From the symptoms that you describe the Nextion has stopped communicating with the Nano on the Raduino board.? The most likely problem is that the connection has come loose.? I would inspect

Hi Don, According to the schematic, the only oscillator is the Si5351, the three outputs of which are used by the device. Since this is a working structure so far, I would first look at the

After a million cycles of WSPR, PSK, JS8CALL, THOR, Olivia, dozens of storms, appalling high SWR with no ATU, and never a complaint (other than when I inflicted malfeasance), my beloved uBITX now

Hello, I have suddenly found a lot of time and would like to include my bitx. I remember reading you could make it deaf if I transmit a strong signal right next to it. How can I avoid this? I know I

+1 for Fldigi for digital modes. It is the total bomb, and it loves the uBITX, or at least the WIN10 computer that usb's to the ubitx and supports hamlib.? I've used Fldigi on a RPi clone under

I just looked at an aftermarket electret mic out of a dead yaesu mic. Was given to me. It had a rubber cover on the element and I changed it to another element and left it bare. Well tonight looking