开云体育

SNAFU: I ordered two uBITX by mistake. The first is up, boxed, and running well. Also have a fine (blue) enclosure for the second unbuilt unit from Ham Radio Kits. Both for $140 shipped CONUS. PayPal.

Andy, some of your frustration is because you are an "early adopter" of the v6 uBitX, and I suspect that fixes and corrections are steadily being done such that by summer it will deliver as a fully

"...(collecting and reposting) doesn't seem to be happening anymore...": Not sure I agree. I think the work being done by the people on http://ubitx.net/ makes it a very valuable resource. That said,

Andy wrote : "This forum/group IS the body of knowledge and support forum. " Which ensures that the same questions will be asked by different people, over and over and over again. In the beginning

Got my uBITX v.6 complete kit yesterday but none of the screws or nuts arrived ( # s ( https://www.facebook.com/hashtag/s?source=feed_text&epa=HASHTAG ) 15-21 on the parts list). Looks like a trip to

Reed, I have seen the same reduced signal in CW mode during key up just prior to time out.? That has been with both my v4 and v5 rigs.? I have always assumed that it was going back to TX in SSB mode

Hi Evan You are of course correct ! I had the frequenciestransposed in my post. Thanks for the information, I'll check it out. 73 Adrian M1LCR / G9X

Another resource is the UBITX.net web page.

Adrian, I believe that you have the crystal filter frequencies mixed up.? The v4 boards use the 12 MHz and the v5 boards use the 11.059 MHz crystals. I would also suggest that you look at the HamsKey

Galactic noise should be reasonably white for these bandwidths. You might find simply looking at received noise is a better way to map the filter. Any software with a "waterfall" should work.

Hi Gary I referred to the v4 pages on the? HF Signals website, here: https://www.hfsignals.com/index.php/ubitx-v4-archived/ In particular the firmware is here:? https://github.com/afarhan/ubitx4??

Hi Dan, Unfortunately I couldn't figure out a way to get SDR# software to do a max-hold function. I agree that would be a useful datapoint. The AirSpyHF+ I'm using isn't calibrated that I'm aware of,

Hi Adrian Which ?firmware did you use as l may have the same problem could you send a link . many thanks Gary

Hello,? I just put my uBITX together today.? I am having a problem where it transmits a tone along with voice on USB and LSB.? Its almost like it is trying to send a CW tone with voice.? I

Thanks, Reed. ?I will try that first thing in the morning! ?Maybe I counted to 10 too fast! ?I’ve been known to be impatient before. Had a v4, but never got it to work very well. ?Finally blew

Hi Bill, There's a "gotcha" with the holding. Pressing and holding the button only works if you're in tuning mode. Try this: * Power off radio * Power on radio * Press and hold tuning button for 10

Andy, My current INO file is at https://github.com/reedbn/ubitxv6/blob/master/ubitxv6.ino. As of right now, it has all of the changes I've made in all of the hex files I've posted for, though it may

New v6. SSB signals sound the same on both LSB and USB. ?Need to adjust BFO. ?I have pressed the knob once (able to select each button). I have pressed the knob twice rapidly ( fast tune mode). I

Thanks for taking the time to reply Ashhar. Where the difficulty is if we were to purchase 10-15 units for a course and load the current release from your github link at the time we get all the files

Hi Ashhar, I tested the code on Win10 Chrome+Firefox and on Android Chrome+Firefox, but I, too, don't have any iOS devices to test against. Reed